Single stage converters for low power stand-alone and grid-connected PV systems

This work presents the evaluation of different power electronic integrated converters suitable for photovoltaic applications, in order to reduce complexity and improve reliability. The rated voltages available in Photovoltaic (PV) modules have usually low values for applications such as regulated output voltages in stand-alone or grid-connected configurations. In these cases, a boost stage or a transformer will be necessary. Transformers have low efficiencies, heavy weights and have been used only when galvanic isolation is mandatory. Furthermore, high-frequency transformers increase the converter complexity. Therefore, the most usual topologies use a boost stage and one inverter stage cascaded. However, the complexity, size, weight, cost and lifetime might be improved considering the integration of both stages. In this context, some integrated converters are analyzed and compared in this paper in order to support future evaluations and trends for low power single-phase inverters for PV systems. Power decoupling, MPPT and Tri-State modulations are also considered. Finally, simulation and experimental results are presented and compared for the analyzed topologies. © 2011 IEEE.

Evaluation of integrated inverter topologies for low power PV systems

This work presents the stage integration in power electronics converters as a suitable solution for solar photovoltaic inverters. The rated voltages available in Photovoltaic (PV) modules have usually low values for applications such as regulated output voltages in stand-alone or grid-connected configurations. In these cases, a boost stage or a transformer will be necessary. Transformers have low efficiencies, heavy weights and have been used only when galvanic isolation is mandatory. Furthermore, high-frequency transformers increase the converter complexity. Therefore, the most usual topologies use a boost stage and one inverter stage cascaded. However, the complexity, size, weight, cost and lifetime might be improved considering the integration of both stages. These are the expected features to turn attractive this kind of integrated structures. Therefore, some integrated converters are analyzed and compared in this paper in order to support future evaluations and trends for low power single-phase inverters for PV systems. © 2011 IEEE.

Micro-inverter for integrated grid-tie PV module using resonant controller

Two-stage isolated converters for photovoltaic (PV) applications commonly employ a high-frequency transformer on the DC-DC side, submitting the DC-AC inverter switches to high voltages and forcing the use of IGBTs instead of low-voltage and low-loss MOSFETs. This paper shows the modeling, control and simulation of a single-phase full-bridge inverter with high-frequency transformer (HFT) that can be used as part of a two-stage converter with transformerless DC-DC side or as a single-stage converter (simple DC-AC inverter) for grid-connected PV applications. The inverter is modeled in order to obtain a small-signal transfer function used to design the PResonant current control regulator. A high-frequency step-up transformer results in reduced voltage switches and better efficiency compared with converters in which the transformer is used on the DC-DC side. Simulations and experimental results with a 200 W prototype are shown. © 2012 IEEE.

Fault current limiter using transformer and modular device of YBCO coated conductor

In this work, we report on the evaluation of a superconducting fault current limiter (SFCL). It is consisted of a modular superconducting device combined with a short-circuited transformer with a primary copper winding connected in series to the power line and the secondary side short-circuited by the superconducting device. The basic idea is adding a magnetic component to contribute to the current limitation by the impedance reflected to the line after transition of the superconducting device. The evaluation tests were performed with a prospective current up to 2 kA, with the short-circuited transformer of 2.5 kVA, 220 V/660 V connected to a test facility of 100 kVA power capacity. The resistive SFCL using a modular superconducting device was tested without degradation for a prospective fault current of 1.8 kA, achieving the limiting factor 2.78; the voltage achieved 282 V corresponding to an electric field of 11 V/m. The test performed with the combined SFCL (xsuperconducting device + transformer) using series and toroidal transformers showed current limiting factor of 3.1 and 2 times, respectively. The test results of the combined SFCL with short-circuited transformer showed undesirable influence of the transformer impedance, resulting in reduction of the fault current level. © 2002-2011 IEEE.

Sensor eletro-óptico de tensões elevadas e sua viabilidade para implementação de TP óptico

Pós-graduação em Engenharia Elétrica - FEIS

Modelo estocástico de programação matemática de alocação de medidores de tensão em alimentadores radiais de distribuição de energia elétrica para localização de faltas e monitoramento do perfil de tensão

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Proposta de diagnóstico para uso, instalação e descarte de transformadores de distribuição recuperados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Características de sistemas de transmissão tetrafásicos submetidos a transitórios lentos e rápidos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise e aplicação de compensação reativa em redes secundária de distribuição com cargas não lineares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise da estabilidade a pequenas perturbações do sistema elétrico de potência considerando a atuação do TCSC e controladores suplementares de amortecimento: representação pelo modelo de sensibilidade de corrente

Pós-graduação em Engenharia Elétrica - FEIS

Estudo de uma ferramenta computacional inteligente para auxiliar a análise de ensaios de impulsos atmosféricos em transformadores de distribuição

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelagem dinâmica de transformadores de corrente para uso em estudos de qualidade da energia e proteção do sistema elétrico

Pós-graduação em Engenharia Elétrica - FEB

Cálculo das perdas técnicas dos transformadores de distribuição, operando em ambiente não-senoidal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desempenho de um algoritmo backward-forward sweep de cálculo de fluxo de potência

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise de sensibilidade através de um modelo implicitamente acoplado para alívio de sobrecargas em redes de transmissão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)