Development of a micro heat exchanger made with ceramic multi-layers (LTCC) and its setup to gas flow measurements

A green ceramic tape micro heat exchanger was developed using LTCC technology. The device was designed by using a CAD software and 2D and 3D simulations using a CFD package (COMSOL Multiphysics) to evaluate the fluid behavior in the microchannels. The micro heat exchanger is composed of five thermal exchange plates in cross flow arrangement and two connecting plates; heat exchanger dimensions are 26 × 26 × 6 mm3. Preliminary tests were carried out to characterize the device both in atmospheric pressure and in vacuum. The same techniques used in vacuum technology were applied to check the rotameters and to prevent device leakages. Thermal performance of the micro heat exchanger was experimentally tested. © 2009 Elsevier B.V. All rights reserved.

Experimental results and thermodynamic analysis of a natural gas small scale cogeneration plant for power and refrigeration purposes

In this work, experimental results are reported for a small scale cogeneration plant for power and refrigeration purposes. The plant includes a natural gas microturbine and an ammonia/water absorption chiller fired by steam. The system was tested under different turbine loads, steam pressures and chiller outlet temperatures. An evaluation based on the 1st and 2nd Laws of Thermodynamics was also performed. For the ambient temperature around 24°C and microturbine at full load, the plant is able to provide 19 kW of saturated steam at 5.3 bar (161 °C), corresponding to 9.2 kW of refrigeration at -5 °C (COP = 0.44). From a 2nd law point-of-view, it was found that there is an optimal chiller outlet temperature that maximizes the chiller exergetic efficiency. As expected, the microturbine presented the highest irreversibilities, followed by the absorption chiller and the HRSG. In order to reduce the plant exergy destruction, it is recommended a new design for the HRSG and a new insulation for the exhaust pipe. © 2013 Elsevier Ltd. All rights reserved.

Optimisation of environmental gas cleaning routes for solid wastes cogeneration systems. Part II - Analysis of waste incineration combined gas/steam cycle

In the first paper of this paper (Part I), conditions were presented for the gas cleaning technological route for environomic optimisation of a cogeneration system based in a thermal cycle with municipal solid waste incineration. In this second part, an environomic analysis is presented of a cogeneration system comprising a combined cycle composed of a gas cycle burning natural gas with a heat recovery steam generator with no supplementary burning and a steam cycle burning municipal solid wastes (MSW) to which will be added a pure back pressure steam turbine (another one) of pure condensation. This analysis aims to select, concerning some scenarios, the best atmospheric pollutant emission control routes (rc) according to the investment cost minimisation, operation and social damage criteria. In this study, a comparison is also performed with the results obtained in the Case Study presented in Part I. (c) 2007 Elsevier Ltd. All rights reserved.

Electrofluid dynamic (EFD) energy conversion in gas flows with suspended nanoparticles

This work presents simulations of the Electrofluid Dynamic energy conversion process in slender channel devices having very small particles (in both micro and nano scales) as charge carriers. Solutions are discussed for a system composed by coupled differential equations, which includes the equation for the total current along the channel, the equations for total energy and momentum of the mixture (gas and solid particles), the continuity equation and the equations for energy and momentum of a single particle. Results for suspended particles of higher diameters have been previously published in the Literature, but the simulations here presented exhibit an appreciable increase in the values for output currents.

Electrofluid dynamic (EFD) energy conversion in gas flows with suspended nanoparticles

This work presents simulations of the Electrofluid Dynamic energy conversion process in slender channel devices having very small particles (in both micro and nano scales) as charge carriers. Solutions are discussed for a system composed by coupled differential equations, which includes the equation for the total current along the channel, the equations for total energy and momentum of the mixture (gas and solid particles), the continuity equation and the equations for energy and momentum of a single particle. Results for suspended particles of higher diameters have been previously published in the Literature, but the simulations here presented exhibit an appreciable increase in the values for output currents.

Grain size effect on the electrical response of SnO2 thin and thick film gas sensors

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development of microvalves for gas flow control in micronozzles using PVDF piezoelectric polymer

This work describes a fabrication and test sequence of microvalves installed on micronozzles. The technique used to fabricate the micronozzles was powder blasting. The microvalves are actuators made from PVDF (polivinylidene fluoride), that is a piezoelectric polymer. The micronozzles have convergent-divergent shape with external diameter of 1mm and throat around 230μm. The polymer have low piezoelectric coefficient, for this reason a bimorph structure with dimensions of 2mm width and 4mm of length was build (two piezoelectric sheets were glued together with opposite polarization). Both sheets are recovered with a conductor thin film used as electrodes. Applying a voltage between the electrodes one sheet expands while the other contracts and this generate a vertical movement to the entire actuator. Appling +300V DC between the electrodes the volume flux rate, for a pressure ratio of 0.5, was 0.36 sccm. Applying -200V DC between the electrodes (that means it closed) the volume flux rate was 0.32 sccm, defining a possible range of flow between 0.32 and 0.36 sccm. The third measurement was performed using AC voltage (200V AC with frequency of 1Hz), where the actuator was oscillating. For pressure ratio of 0.5, the flow rate was 0.62 sccm. © 2008 IOP Publishing Ltd.

A comparative study of glycerol dehydration catalyzed by micro/mesoporous MFI zeolites

The catalytic properties of monomodal microporous and bimodal micro-mesoporous zeolites were investigated in the gas-phase dehydration of glycerol. The desilication methodology used to produce the mesoporous zeolites minimized diffusion limitations and increased glycerol conversion in the catalytic reaction due to the hierarchical system of secondary pores created in the zeolite crystals. The chemical and structural properties of the catalyst were studied by X-ray diffraction, nitrogen adsorption-desorption isotherms, NH3-TPD and pyridine chemisorption followed by IR-spectroscopy. Although the aim was to desilicate to create mesoporosity in the zeolite crystals, the desilication promoted the formation of extra-framework aluminum species that affected the conversion of glycerol and the products distribution. The results clearly show that the mesoporous zeolites with designed mesopore structure allowed a rapid diffusion and consequently improved the reaction kinetics. However, especial attention must be given to the desilication procedure because the severity of the treatment negatively interfered on the Brønsted and Lewis acid sites relative concentration and, consequently, in the efficiency of the catalysis performed by these materials. On the other hand, during the catalytic reaction, the intracrystalline mesopores allowed carbonaceous compounds to be deposited herein, resulting in less blocked micropores and catalysts with higher long-term stability.

Desenvolvimento de sistema computacional para pré-dimensionamento de turbinas para micro, mini e pequenas centrais hidrelétricas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Produção e caracterização de micro e nanofibras de Poli(fluoreto de vinilideno) - PVDF obtidos pela técnica de fiação por sopro em solução

Pós-graduação em Ciência dos Materiais - FEIS

Síntese de nanoestruturas de ZnO por redução carbotérmica e hidrotermal, assistido por micro-ondas: caracterização como sensor

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação da viabilidade de implantação de uma micro- central hidroelétrica para atender consumidores localizados em regiões isoladas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Polihidroxialcanoatos (PHAs): bioprospecção de micro-organismos e produção a partir de glicerol

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Micro-fungos de interesse para o setor de petróleo, gás e biocombustíveis

Oil is a hydrocarbon mixture of various sizes, including saturated and aromatic compounds. Natural gas is a mixture of gaseous hydrocarbons and its main component is methane. In our society, the great demand for these fuels requires fast extraction, transportation and refining, increasing the number of accidents that compromise the environment. Oil is a finite resource and it is necessary to reduce the problems related to the question concerning environmental pollution which has encouraged the search for alternative fuel sources in our country. So today we have two major biofuels: ethanol and biodiesel. Concurrently, many studies have been done directed toward the isolation of microorganisms capable of degrading petrochemical industrial wastes, most of them using as a source of isolation soil and water collected in a contaminated environment. Isolation from alternative substrates has emerged as a new strategy that has provided satisfactory results. In this work, we present the leaf-cutter ants of the Attini tribe as a source for the isolation of micro-fungi with the potential for hydrocarbon degradation. These insects have a social way of life and a highly specialized system of intra and interspecific communication, which is based on the recognition of individuals through volatile chemical compounds, the majority hydrocarbons, stored in their exoskeleton. The micro-environment exoskeleton of Attini ants (genus Atta) used in this work proved to be a rich source of microbial biodiversity, as other studies have found. The flotation isolation technique applied here allowed the achievement of 214 micro-fungi, 118 representatives of the dematiaceous fungi group and 96 hyaline filamentous fungi. They were submitted to toluene degradation tests and at least one strain of each genus presented good results, namely Teratosphaeria, Exophiala, Cladosporium, Penicillium, Aspergillus... (Complete abstract click electronic access below)

Propriedades físico-químicas e mecânicas, potencial bioativo e caracterização da interface dentina-cimento de cimentos endodônticos experimentais à base de cimento Portland associados à radiopacificadores micro e nanoparticulados

Pós-graduação em Odontologia - FOAR