Internal adaptation of cast titanium crowns

As the adaptation of titanium crowns obtained by Rematitan Plus investment, specific for titanium, is not recognized to be suitable, this study evaluated the effect of the concentration of the specific liquid and the temperature of the mold of investments on the internal misfit of crowns cast on commercially pure titanium. Individual dies of epoxy resin were obtained, representing teeth prepared for full-crown restoration with a 6-degree axial surface convergence angle and shoulder (1.0 mm). For the waxing of each crown, a ring-shaped stainless steel matrix (8.0mm internal diameter; 7.5 mm height) was adapted above the individual dies of epoxy resin. The Rematian Plus investment was mixed according to the manufacturer's instructions using two different concentrations of the specific liquid: 100%, 75%. Casting was performed in a Discovery Plasma Ar-arc vacuum-pressure casting machine with molds at temperatures of 430°C, 515°C and 600°C. The crowns were cleaned individually in a solution (1% HF + 13% HNO3) for 10 min using a ultrasonic cleaner, with no internal adaptations, and luted with zinc phosphate cement under a 5 kg static load. The crown and die assemblies were embedded in resin and sectioned longitudinally. The area occupied by cement was observed using stereoscopic lens (10X) and measured by the Leica Qwin image analysis system (mm2). The data for each experimental condition (n=8) were analyzed by Kruskal-Wallis non-parametric test (á=0.05). The results showed that liquid dilution and the increase in mold temperature did not significantly influence the levels of internal fit of the cast titanium crowns. The lowest means (±SD) of internal misfit were obtained for the 430°C/100%: (7.25 mm2 ±1.59) and 600°C/100% (8.8 mm2 ±2.25) groups, which presented statistically similar levels of internal misfit.

Effect of phosphate-bonded investments on titanium reaction layer and crown fit

This study analyzed the reaction layer and measured the marginal crown fit of cast titanium applied to different phosphate-bonded investments, prepared under the following conditions (liquid concentration/casting temperature): Rema Exakt (RE) - 100%/237°C, 75%/287°C, Castorit Super C (CS)-100%/70°C, 75%/141°C and Rematitan Plus (RP)-100%/430°C (special to titanium cast, as the control group). The reaction layer was studied using the Vickers hardness test, and analyzed by two way ANOVA and Tukey's HSD tests (α = 0.05). Digital photographs were taken of the crowns seated on the die, the misfit was measured using an image analysis system and One-way ANOVA, and Tukey's test was applied (α = 0.05). The hardness decreased from the surface (601.17 VHN) to 150 μm (204.03 VHN). The group CS 75%/141°C presented higher hardness than the other groups, revealing higher surface contamination, but there were no differences among the groups at measurements deeper than 150 μm. The castings made with CS - 100%/70°C presented the lowest levels of marginal misfit, followed by RE -100%/237°C. The conventional investments CS (100%) and RE (100%) showed better marginal fit than RP, but the CS (75%) had higher surface contamination.

Development of a burner to measure biogas generation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evolução do processo de espermiação em machos de Piau, Leporinus macrocephalus, hormonalmente induzidos à reprodução

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de uma Plataforma de Software para a Modelagem Digital de Terrenos baseada em TIN

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise discriminatória de alvos da paisagem urbana em imagens aéreas multiespectrais

Pós-graduação em Ciências Cartográficas - FCT

Comparação entre a capacidade de desobturação de canais radiculares obturados com cimentos à base de MTA, polímero da mamona e resina epóxica utilizando instrumento manual ou rotatório

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Diagnóstico de situação das práticas de manejo sanitário em sistemas de produção de bovinos de corte

Pós-graduação em Ciência Animal - FMVA

Emprego da fotografia digital para avaliação da topografia microscópia da pele

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise dos sprays de jatos de injetores de motor foguete utilizando um sistema de processamento digital de imagens

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do armazenamento prolongado em água sobre a resistência de união entre resinas para reembasamento e resina para base de prótese

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da viabilidade do emprego da técnica de subtração radiográfica digital em radiografias periapicais com registro a posteriori

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento e validação geométrica de um sistema para mapeamento com câmeras digitais de médio formato

Pós-graduação em Ciências Cartográficas - FCT

Análise da cicatrização na pele de coelhos após tratamentos de feridas com biomateriais associados à fração de proteína do látex natural da seringueira (Hevea brasiliensis)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento e avaliação de pulverizador florestal com detecção eletrônica de plantas daninhas e aplicação em doses variáveis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)