Search for Neutral Higgs Bosons at High tan beta in the b(h/H/A) -> b tau(+)tau(-) Channel

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Tracing source and evolution of suspended particles in the Rio Negro Basin (Brazil) using chemical species of iron

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comparative study of Cr3C2-NiCr coatings obtained by HVOF and hard chromium coatings

In the present work the corrosion resistance of micro-cracked hard chromium and Cr3C2-NiCr (HVOF) coatings applied on a steel substrate have been compared using open-circuit potential (E-OC) measurements, electrochemical impedance spectroscopy (EIS) and polarization curves. The coatings surfaces and cross-section were characterized before and after corrosion tests using optical microscopy (OM) and scanning electron microscopy (SEM). After 18 h of immersion, the open-circuit potential values were around -0.50 and -0.25V/(Ag vertical bar AgCl vertical bar KClsat) for hard chromium and Cr3C2- NiCr, respectively. The surface analysis done after 12 h of immersion showed iron on the hard chromium surface inside/near surface cracks, while iron was not detected on the Cr3C2-NiCr surface even after 18 h. For longer immersion time hard chromium was more degraded than thermal sprayed coating. For hard chromium coating a total resistance values between 50 and 80 k Omega cm(2) were measured and two well-defined time constants were observed, without significant change with the immersion time. For Cr3C2-NiCr coating the total impedance diminished from around 750 to 25 k Omega cm(2) as the immersion time increased from 17 up to 132 h and two overlapped time constants were also observed. Polarization curves recorded after 18 h of immersion showed a lower current and higher corrosion potential for Cr3C2-NiCr coating than other samples studied. (c) 2005 Elsevier Ltd. All rights reserved.

Colloidal particles: Spherical yttrium iron garnet

The purpose of this work is to obtain spherical particles YIG from micrometric to nanometric scales. The spherical particles were obtained from cation hydrolysis in acid medium by adding urea or ammonia in order to carry out a homogeneous nucleation process up to 90 degrees C. Different composition and morphology were achieved by changing reactant concentrations, precipitation agent and stabilizing agent. X-ray diffractometry, electrophoretic mobility, transmission and scanning electron microscopies were carried out on these particles to investigate the phase identification, mobility, morphology and particle size. Crystalline YIG, with spherical characteristics, was obtained. The surface potential presented different characteristics for different dispersion media.

Cr3C2-NiCr and WC-Ni thermal spray coatings as alternatives to hard chromium for erosion-corrosion resistance

Cr3C2-NiCr and WC-Ni coatings are widely used for wear applications at high and room temperature, respectively. Due to the high corrosion resistance of NiCr binder, Cr3C2-NiCr coatings are also used in corrosive environments. The application of WC-Ni coatings in corrosive media is 14 not recommended due to the poor corrosion resistance of the (pure Ni) metallic matrix. It is well known that the addition of Cr to the metallic binder improves the corrosion properties. Erosion-corrosion performance of thermal spray coatings is widely influenced by ceramic phase composition, the size of ceramic particles and also the composition of the metallic binder. In the present work, two types of HVOF thermal spray coatings (Cr3C2-NiCr and WC-Ni) obtained with different spray conditions were studied and compared with conventional micro-cracked hard chromium coatings. Both as-sprayed and polished samples were tested under two erosion-corrosion conditions with different erosivity. Tungsten carbide coatings showed better performance under the most erosive condition, while chromium carbide coatings were superior under less erosive conditions. Some of the tungsten carbide coatings and hard chromium showed similar erosion-corrosion behaviour under more and less erosive conditions. The erosion-corrosion and electrochemical results showed that surface polishing improved the erosion-corrosion properties of the thermally sprayed coatings. The corrosion behaviour of the different coatings has been compared using Electrochemical Impedance Spectroscopy (EIS) and polarization curves. Total material loss due to erosion-corrosion was determined by weight loss measurements. An estimation of the corrosion contribution to the total weight loss was also given. (c) 2007 Elsevier B.V. All rights reserved.

Diclofenac Abatement using Modified Solar Photo-Fenton Process with Ammonium Iron(III) Citrate

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Food partitioning between breeding White-tailed Kites (Elanus leucurus; Aves; Accipitridae) and Barn Owls (Tyto alba; Aves; Tytonidae) in southern Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On Ti-18Si-6B and Ti-7.5Si-22.5B powder alloys prepared by high-energy ball milling and sintering

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Characterization and catalytic activity of iron(III) mono(4-N-methyl pyridyl)-tris(halophenyl) porphyrins in homogeneous and heterogeneous systems

The synthesis, characterization and catalytic activity of the cationic iron porphyrins Fe[M(4-N-MePy)TDCPP]Cl-2 and Fe[M(4-N-MePy)TFPP]Cl-2 in the epoxidation of (Z)-cyclooctene by PhIO in homogeneous solution and supported on silica gel (SG), imidazole propyl gel (IPG) or SG modified with 2-(4-sulfonatophenyl)ethyl groups (SiSO3) have been accomplished. When supported on IPG, both cationic FeP bind to the support via Fe-imidazole coordination. Fe[M(4-N-MePy)TDCPP]IPG contains a mixture of low-spin bis-coordinated (FeP)-P-III and high-spin mono-coordinated (FeP)-P-III species, whereas Fe[M(4-N-MePy)TFPP]IPG only contains high-spin mono-coordinated (FeP)-P-III. These FePIPG catalysts also contain (FeP)-P-II species, whose presence was confirmed by EPR spectroscopy using NO as a paramagnetic probe. Both cationic FePs coordinate to SG through Fe-O ligation and they are present as high-spin (FeP)-P-III species. The cationic FePs supported on SiSO3- are also high-spin (FeP)-P-III species and they bind to the support via electrostatic interaction between the 4-N-methylpyridyl groups and the SO3- groups present on the matrix. In homogeneous solution, both Fe[M(4-N-MePy)TDCPP]Cl-2 and Fe[M(4-N-MePy)TFPP]Cl-2 have similar catalytic activity to Fe(TDCPP)Cl and Fe(TFPP)Cl, leading to cis-epoxycyclooctane yields of 92%. When supported on inorganic matrices,both FePs lead to epoxide yields comparable to their homogeneous analogues and their anchoring enables catalyst recovery and re-use. Recycling of Fe[M(4-N-MePy)TDCPP]SiSO3- shows that this FeP maintains its activity in a second reaction. (C) 1999 Elsevier B.V. B.V. All rights reserved.

From Plinthic Acrisols to Plinthosols and Gleysols: iron and groundwater dynamics in the tertiary sediments of the upper Amazon basin

Topography has been reported to be the major factor ruling the spatial distribution of Acrisols, Plinthosols and Gleysols on the seasonally flooded, low elevation plateaux of the upper Amazon basin occupied by Tertiary (Ica & Solimoes) sediments. In this study, detailed morphological and mineralogical investigations conducted in a representative 25-ha site were combined with hydro-geochemical data to relate the vertical and lateral soil differentiations observed to the hydro-geological history of that part of the basin. As a result of the uplift of the Andes, several cuts in the extensive Tertiary marshlands have formed, at first, slightly incised plateaux of low elevation. There, weathering under hot and humid climates would have generated a reddish, freely drained and bioturbated topsoil layer and the vertical differentiation in subsoil sediments of a plinthite over an iron-depleted mottled clay. The second episode of soil differentiation is linked to the replacement of the forest by a savannah under the drier climates of the late Pleistocene, which favours surface runoff and the infill of the incisions by fine particles. This infill, combined with the return to the present humid climate, has then enabled the local groundwater to rise on the plateaux and to generate episaturation at the topsoil/subsoil transition close to the depressions. Nowadays, ferrous iron is released from the partly iron-depleted topsoil weathering front at high water levels during the rainy seasons. It moves from footslope to low-lying positions and from top to bottom in the soil profile according to the groundwater dynamics. The present general trend is thus to the lateral export of iron at high water levels due to subsurface and overland flows, its vertical transfer during the recession of the groundwater and accumulation in a nodular plinthite. In the latter, ferrous iron is adsorbed onto its softest iron masses where it feeds the neoformation of ferrihydrite that rapidly dehydrates into haematite.

Serum iron and plasma fibrinogen concentrations as indicators of systemic inflammatory diseases in horses

Background: Detection of systemic inflammation, which is important for proper diagnosis and prompt treatment, can be challenging.Hypothesis: Measurement of plasma iron concentration is a sensitive method for detecting systemic inflammation in horses compared with measurements of plasma Fibrinogen concentration, a traditional marker for inflammation in the horse.Animals: Ninety-seven horses hospitalized with diseases causing systemic inflammation, 22 horses with localized inflammation, and 12 clinically normal horses were included in this study.Methods: A retrospective study was made on hospitalized horses that had both plasma iron and fibrinogen concentrations measured on hospital admission.Results: Plasma iron concentration was lower in horses with systemic inflammation (64 +/- 45 mu g/dL) than the reference interval minimum (105 mu g/dL) and were significantly lower (P = .001) than the value in a group of horses with local inflammation (123 +/- 45 mu g/dL) and in healthy transported horses (143 +/- 29 mu g/dL). Low plasma iron and high fibrinogen concentrations were both sensitive indicators of systemic inflammation in horses with sensitivity of 90 and 82%, respectively. There was a similar correlation between either continued decreases in iron concentration (R-sp of 0.239) or increases in fibrinogen concentration (R-sp of 0.280) during hospitalization and a worse prognosis.Conclusions and Clinical Importance: Measurement of plasma iron concentration better reflected acute inflammation than did fibrinogen concentration.

Small-angle X-ray scattering and X-ray absorption near-edge structure study of iron-doped siloxane-polyoxyethylene nanocomposites

The local and medium-range structures of siloxane-POE hybrids doped with Fe(III) ions and prepared by the sol-gel process were investigated by X-ray absorption near-edge structure (XANES)/extended X-ray absorption fine structure (EXAFS) and small-angle X-ray scattering (SAXS), respectively. The experimental results show that the structure of these composites depends on the doping level. EXAFS data reveal that, for low doping levels ([O]/[Fe] > 40, oxygens being of the ether-type of the POE chains), Fe(III) ions are surrounded essentially by a shell of chlorine atoms, suggesting the formation of FeCl4- anions. At high doping levels ([O]/[Fe] < 20), Fe(III) ions interacts mainly with oxygen atoms and form FeOx species. The relative proportion of FeOx species increases with iron concentration, this result being consistent with the results of SAXS measurements showing that increasing iron doping induces the formation of iron-rich nanodomains embedded in the polymer matrix.

Factors which affect the catalytic activity of iron(III) meso tetrakis(2,6-dichlorophenyl)porphyrin chloride in homogeneous system

An optimization study of the reaction conditions of Fe(TDCPP)Cl when it is used as catalyst in the hydroxylation of cyclohexane by iodosylbenzene (PhIO) has been carried out, It was found that Fe(TDCPP)Cl follows the classical PhIO mechanism described for Fe(TPP)Cl, which involves the monomeric active species Fe-IV(O)P-+. (I). In the optimized condition ([Fe(TDCPP) = 3.0 X 10(-4) mol l(-1) in 1,2-dichloroethane (DCE); ultrasound stirring at 0 degrees C; PhIO/FeP molar ratio = 100), this FeP led to a yield of cyclohexanol (C-ol) of 96% and a turnover number of 96, Therefore, Fe(TDCPP)Cl may be considered a good biomimetic model and a very stable, resistant and selective catalyst, which yields C-ol as the sole product. DCE showed to be a better solvent than dichloromethane (DCM), 1 DCE:1 MeOH mixture or acetonitrile (ACN). Since the Fe-IV(O)P-+. is capable of abstracting hydrogen atom from DCM, MeOH or ACN, the solvent competes with the substrate. Presence of O-2 lowers the yield of C-ol, as it can further oxidize this alcohol to carboxylic acid in the presence of radicals, Presence of H2O also causes a decrease in the yield, since it converts the active species I into Fe-IV(OH)P, which cannot oxidize cyclohexane. Addition of excess imidazole or OH- to the system results in a decrease in the yield of C-ol, due to the formation of the hexacoordinated complexes Fe(TDCPP)Im(2)(+) (low-spin, beta(2) = 2.5 X 10(8) mol(-2) l(2)) and Fe(TDCPP)(OH)(2)(-) (high-spin, beta(2) = 6.3 X 10(7) mol(-2) l(2)), the formation of both Fe(TDCPP)Im(2)(+) and Fe(TDCPP)(OH)(2)(-) complexes were confirmed by EPR studies. The catalytic activities of Fe(TDCPP)C and Fe(TFPP)Cl were compared, the unusually high yields of C-ol with Fe(TFPP)Cl obtained when ultrasound, DCM and O-2 atmosphere were used, suggest that a parallel mechanism involving the mu-oxo dimer form, O-2 and radicals may also be occurring with this FeP, besides the PhIO mechanism.

Characterization and catalytic activity of 2,6-dichlorophenyl substituted iron(III) porphyrin supported on silica gel and imidazole propyl gel

In this work we have made use of the study of the interaction between Fe(TDCPP)(+) and the axial ligands OH- and imidazole in order to help characterize the heterogenized catalysts Fe(TDCPP)SG and Fe(TDCPP)IPG through UV-VIS and EPR spectroscopies and thus, better understand their different catalytic activity in the oxidation of cyclohexane by PhIO. We have found out that in Fe(TDCPP)SG (containing 1.2 X 10(-6) mol Fe(TDCPP)(+)/g of support), the FeP bis-coordinates to silica gel through Fe-O coordination and it is high-spin (FeP)-P-III species. In Fe(TDCPP)IPG 1 (containing 1.1 X 10(-6) mol Fe(TDCPP)(+) and 2.2 X 10(-4) mol imidazole/g of support), the FeP is bis-ligated to imidazole propyl gel through Fe-imidazole coordination and using NO as a paramagnetic probe, we present evidence that Fe(TDCPP)(+) is present as a mixture of low-spin (FeP)-P-III and (FeP)-P-II species. This catalyst led to a relative low yield of cyclohexanol (25%) because the bis-coordination of the (FeP)-P-III to the support partially blocks the reaction between Fe(TDCPP)(+) and PhIO, thus leading to the formation of only a small amount of the active species Fe-IV(OP+, while the (FeP)-P-II species do not react with the oxygen donor. Increasing the amount of Fe(TDCPP)(+) and decreasing the amount of imidazole in the support led to the obtention of high-spin (FeP)-P-III EPR signals in the spectra of Fe(TDCPP)IPG 5 (containing 4.4 X 10(-6) mol Fe(TDCPP)(+) and 2.2 X 10(-5) mol imidazole/g of IPG), together with low-spin (FeP)-P-III species. This latter catalyst led to better cyclohexanol yields (67%) than Fe(TDCPP)IPG 1. Fe(TDCPP)IPG 5 was further used in a study of the optimization of its catalytic activity and in recycling experiments in the optimized conditions. Recycling oxidation reactions of Fe(TDCPP)IPG 5 led to a total turnover number of 201 and total cyclohexanol yield of 201%, which could not be attained with Fe(TDCPP)Cl in homogeneous solution (turnover = 96) due to the difficulty in recovering and reusing it.

Ferritin in iron containing granules from the fat body of the honeybees Apis mellifera and Scaptotrigona postica

It is already known that the behaviour of the honeybee Apis mellifera is influenced by the Earth's magnetic field. Recently it has been proposed that iron-rich granules found inside the fat body cells of this honeybee had small magnetite crystals that were responsible for this behaviour. In the present work, we studied the iron containing granules from queens of two species of honeybees (A. mellifera and Scaptotrigona postica) by electron microscopy methods in order to clarify this point. The granules were found inside rough endoplasmic reticulum cisternae. Energy dispersive X-ray analysis of granules from A. mellifera showed the presence of iron, phosphorus and calcium. The same analysis performed on the granules of S. postica also indicated the presence of these elements along with the additional element magnesium. The granules of A. mellifera were composed of apoferritin-like particles in the periphery while in the core, clusters of organised particles resembling holoferritin were seen. The larger and more mineralised granules of S. postica presented structures resembling ferritin cores in the periphery, and smaller electron dense particles inside the bulk. Electron spectroscopic images of the granules from A. mellifera showed that iron, oxygen and phosphorus were co-localised in the ferritin-like deposits. These results indicate that the iron-rich granules of these honeybees are formed by accumulation of ferritin and its degraded forms together with elements present inside the rough endoplasmic reticulum, such as phosphorus, calcium and magnesium. It is suggested that the high level of phosphate in the milieu would prevent the crystallisation of iron oxides in these structures, making very unlikely their participation in magnetoreception mechanisms. They are most probably involved in iron homeostasis. (C) 2001 Elsevier B.V. Ltd. All rights reserved.