Detection and Identification of Abnormalities in Customer Consumptions in Power Distribution Systems

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Weathering degradation of polyester and polypropylene geotextiles

This paper presents results of physical and mechanical tests in polyester (PET) and polypropilene (PP) nonwoven geotextiles that were exposed to weathering conditions (solar radiation, humidity, wind, rain) after some specific periods of exposure (1, 2, 3 and 4 months). ASTM D5970 and Brazilian standards (NBR) recommendation were followed in this research. Results show variations in tensile properties and in the mass per unit area. Variations in the deformations were more significant in the PP geotextile when compared to the PET geotextile.

Calcium levels and limestone particle size in the diet of commercial layers at the end of the first production cycle

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Calcium and available phosphorus levels for laying hens in second production cycle

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Osteoconductive Properties of beta-Tricalcium Phosphate Matrix, Polylactic and Polyglycolic Acid Gel, and Calcium Phosphate Cement in Bone Defects

Extensive bone defects in maxillofacial region can be corrected with autogenous grafts; otherwise, the disadvantages of the therapeutics modality take the research for new bone substitutes. The aim of the study was to evaluate and compare the osteoconductive properties of 3 commercial available biomaterials. A total of 30 calvarial defects (5-mm diameter) were randomly divided into 5 treatment groups, with a total of 6 defects per treatment group (n = 6). The treatment groups were as follows: 500 to 1000 Km beta-tricalcium phosphate (beta-TCP), polylactic and polyglycolic acid (PL/PG) gel, calcium phosphate cement, untreated control, and autograft control. The evaluations were based on histomorphometric analysis at 60 postoperative days. The results have shown that beta-TCP and autograft control supported bone formation at 60 postoperative days. beta-Tricalcium phosphate showed the highest amount of mineralized area per total area and statistically significant compared with PL/PG, calcium phosphate cement, and untreated control groups. The PL/PG gel does not have osteoconductive properties and performed similar to empty control. Calcium phosphate cement showed higher number of multinucleated giant cells around the sites of the biomaterial and showed newly formed bone only at the edges of the biomaterial, without bone formation within the biomaterial. The findings presented herein indicate that bone formation reached a maximum level when rat calvarial defects were filled with beta-TCP at 60 postoperative days. Further studies should be conducted with beta-TCP to understand the potential of this biomaterial in bone regeneration.

Seed predation and fruit damage of Solanum lycocarpum (Solanaceae) by rodents in the cerrado of central Brazil

Although neotropical savannas and grasslands, collectively referred to as cerrado, are rich in seed-eating species of rodents, little is known about seed predation and its determinants in this habitat. In this study, we investigated seed predation and damage to fruits of the widespread shrub Solarium lycocarpurn. In addition, the influence of two possible determinants (distance from the parental plant and total crop size) on the feeding behaviour of Oryzorrys scotti (Rodentia, Sigmodontinae) was also examined. O. scotti were captured more frequently close to the shrubs or on shrub crops, indicating that these rodents were attracted to the shrubs and that seed predation was probably distance-dependent. Moreover, the proportion of damaged fruit on the plant decreased as the total crop size increased; consequently, more productive plants were attacked proportionally less by rodents. This pattern of fruit damage may reflect predator satiation caused by the consumption of a large amount of pulp. Alternatively, secondary metabolites in S. lycocarpum fruits may reduce the pulp consumption per feeding event, thereby limiting the number of fruits damaged. (c) 2006 Elsevier Masson SAS. All rights reserved.

Densidade de plantio na produtividade e nos teores de nutrientes nas folhas e frutos da bananeira cv. Thap Maeo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Interferência das plantas daninhas na cultura do amendoim das águas: efeitos de espaçamentos, variedades e períodos de convivência

O presente experimento, conduzido em Jaboticabal, SP, em Latossolo Vermelho Escuro, textura média, teve por objetivo verificar a interferência de plantas daninhas sobre aspectos da produção do amendoim. O delineamento experimental adotado foi o de blocos casualizados, com três repetições, dispostos em esquema fatorial 2x2x8. Constituíram variáveis duas variedades (Tatu e Tatui), dois espaçamentos entre sulcos de semeadura (0,4 e 0,6 m) e oito períodos de controle manual da comunidade infestante (sem controle e com controle até os 10, 20, 30, 40, 50, 60 dias e até o final do ciclo da cultura, a partir da emergência do amendoim). A principal planta daninha presente na área experimental foi Pennisetum setosum e, nos espaçamentos de 0,4 e 0,6 m foram necessários 10 e 30 dias de controle, respectivamente, para reduzir significativamente a sua biomassa seca. O número de vagens por planta foi o principal parâmetro produtivo afetado pela interferência da comunidade infestante. Os espaçamentos utilizados não afetaram singnificativemente o período total de prevenção da interferência das plantas daninhas na produtividade do amendoim. Verificou-se que tal período foi de 10 e 20 dias para a variedade Tatuí e Tatu, respectivamente.

Hair coat characteristics and sweating rate of Braford cows in Brazil

This paper deals with the effects of hair coat characteristics on the sweating rate of Brazilian Braford cows and estimation of heritabilities and genetic correlations of these traits. Data (n=1607) on hair length, coat thickness, hair diameter, number of hairs per unit area, coat reflectance and sweating rate were recorded from heifers and cows of a commercial herd managed on range under extensive system. The data were analyzed considering the following effects on the model for hair coat traits: classes of sires and contemporary groups; linear effects of month and genotype; linear and quadratic effects of age. The effect of sire was important (P<0.05) for all hair coat traits, except for number of hairs; contemporary groups affected (P<0.05) all hair coat traits; the effect of sampling month was important (P<0.05) for hair length and reflectance; genotype affected (P<0.05) hair length, diameter and coat reflectance; the quadratic effect of age was important (P<0.05) only for coat reflectance. Two models were used to analyze the sweating rate. The first model considered the following fixed effects: classes of contemporary groups and sires; linear effect of genotype, coat thickness, hair length, hair diameter, number of hairs, coat reflectance; linear and quadratic effects of time of day, age, air temperature, partial vapour pressure and radiant heat load. The second model used for the sweating rate considered the same fixed effects for the first model, except that the hair coat characteristics were adjusted for important effects used in the models to analyze hair coat traits. All meteorological factors and contemporary groups were important (P<0.05) on variation of sweating rate in both models. The Restricted Maximum. Likelihood (REML) method was used to estimate variance and covariance components under the sire model. Results included heritability estimates in narrow (h(2)) and broad (H) sense for single-trait analyzes: hair thickness (h(2)=0.16; H-2=0.26); hair length (h(2)=0.18; H-2=0.39); number of hairs (h(2)=0.08 +/- 0.07; H-2=0.08 +/- 0.07); hair diameter (h(2)=0.12 +/- 0.07; H-2=0.12 +/- 0.07); coat reflectance (h(2)=0.30; H-2=0.42); and sweating rate (h(2)=0.10 +/- 0.07; H-2=0.10 +/- 0.07). In general, the genetic correlations between the adaptive traits were favorable as for the direction to select for adaptation in tropical environment; however, they presented high standard errors. The results of this study imply that hair coat characteristics and sweating ability are important for the adaptability to heat stress and they must be better studied and further considered for selection for genetic progress of adaptation in tropical environment. (C) 2007 Elsevier B.V All rights reserved.

Pressure field along the axis of a high-power klystron amplifier

The pressure field in a high-power klystron amplifier is investigated to scale the ionic vacuum pump used to maintain the ultra high-vacuum in the device in order to increase its life-time. The investigation is conducted using an 1.3 GHz, 100 A - 240 keV high-power klystron with five reentrant coaxial cavities, assembled in a cylindrical drift tube 1.2 m long. The diffusion equation is solved to the regime molecular flow to obtain the pressure profile along the axis of the klystron drift tube. The model, solved by both analytical and numerical procedures, is able to determine the pressure values in steady-state case. This work considers the specific conductance and all important gas sources, as in the degassing of the drift tube and cavities walls, cathode, and collector. For the drift tube degassing rate equals to q(deg) = 2x10(-12) (-)mbar.L.s(-1) cm(-2) (degassing rate per unit area), to cavities q(cavity) = 3x10(-13) mbar.L.s(-1)cm(-2), to the cathode q(cathode) = 6x10(-9)_mbar.L.s(-1) and to the collector q(collector) = 6x10(-9) mbar.L.s(-1), it was found that a 10 L.s(-1) ionic vacuum pump connected in the output waveguide wall is suitable. In this case, the pressure obtained in the cathode is p(cathode) = 6.3x10(-9) mbar, in the collector p(collector) = 2.7x10(-9) mbar, and in the output waveguide p = 2.1x10(-9) mbar. Although only the steady-state case is analyzed, some aspects that may be relevant in a transient situation, for instance, when the beam hits the drift tube walls, producing a gas burst, is also commented.

Effect of lesion age, humidity, and fungicide application on sporulation of Alternaria alternata, the cause of brown spot of tangerine

Alternaria brown spot, caused by Alternaria alternata, causes yield losses and fruit blemishes on many tangerines and their hybrids in most citrus areas of the world where susceptible cultivars are grown. Although the conditions affecting infection and disease severity are known, little information is available on inoculum production on infected tissue. We found that sporulation on leaves began about 10 days after symptoms developed, was abundant from 20 to 40 days, and declined thereafter. Conidial production was far greater on leaf than on fruit or twig lesions. Spore production per unit area of leaf lesion was greater on the more susceptible hybrids, Minneola and Orlando tangelos, than on the less susceptible Murcott tangor. At 74% relative humidity, conidial production on leaf lesions was low, but it was abundant at 85, 92.5, 96, and 100%. Application of Q(o)I or copper fungicides, but not ferbam, suppressed sporulation on leaf lesions for about 14 to 21 days after application. Additional applications did not appear to be more effective than a single spray in reducing inoculum production.

Potential force of infection of human rabies transmitted by vampire bats in the Amazonian region of Brazil

Human rabies tansmitted by bats has acquired greater epidemiologic relevance in various Latin American countries, just when cases transmitted by dogs have decreased. Concern has been heightened by reports of increased rates of bats biting humans in villlages in the Amazonian region of Brazil. The aim of the present work was to estimate the potential force of infection (per capita rate at which susceptible individuals acquire infection) of human rabies transmitted by the common vampire bat if the rabies virus were to be introduced to a colony of bats close to a village with a high rate of human bites. The potential force of infection could be then used to anticipate the size of a rabies outbreak in control programs. We present an estimator of potential incidence, adapted from models for malaria. To obtain some of the parameters for the equation, a cross-sectional survey was conducted in Mina Nova, a village of gold prospectors in the Amazonian region of Brazil with high rates of bates biting humans. Bats were captured near dwellings and sent to the Rabies Diagnostic Laboratory at the Center for Control of Zoonoses (São Paulo, Brazil) to be examined. To estimate the force of infection, a hypothetical rabies outbreak among bats was simulated using the actual data obtained in the study area. of 129 people interviewed, 23.33% had been attacked by a vampire bat during the year prior to the study, with an average of 2.8 bites per attacked person. Males (29.41%) were attacked more often than females (11.36%); also, adults (29.35%) were attacked more often than children (8.33%). None of the 12 bats captured in Mina Nova tested positive for rabies, but the force of infection for a hypothetical outbreak was estimated to be 0.0096 per person per year. This risk represents 0.96 cases per 100 area residents, giving an incidence of 1.54 cases of bat-transimtted buman rabies per year in the village of Mina Nova (160 inhabitants). The estimated risk is comparable with what has been observed in similar Brazilian villages.

Life-cycle inventory for hydroelectric generation: a Brazilian case study

Representative Life-Cycle Inventories (LCIs) are essential for Life-Cycle Assessments (LCAs) quality and readiness. Because energy is such an important element of LCAs, appropriate LCIs on energy are crucial, and due to the prevalence of hydropower on Brazilian electricity mix, the frequently used LCIs are not representative of the Brazilian conditions. The present study developed a LCI of the Itaipu Hydropower Plant, the major hydropower plant in the world, responsible for producing 23.8% of Brazil's electricity consumption. Focused on the capital investments to construct and operate the dam, the LCI was designed to serve as a database for the LCAs of Brazilian hydroelectricity production. The life-cycle boundaries encompass the construction and operation of the dam, as well as the life-cycles of the most important material and energy consumptions (cement, steel, copper, diesel oil, lubricant oil), as well as construction site operation, emissions from reservoir flooding, material and workers transportation, and earthworks. As a result, besides the presented inventory, it was possible to determine the following processes, and respective environmental burdens as the most important life-cycle hotspots: reservoir filling (CO(2) and CH(4) emission: land use); steel life-cycle (water and energy consumption; CO, particulates, SO(x) and NO(x) emissions); cement life-cycle (water and energy consumption; CO(2) and particulate emissions); and operation of civil construction machines (diesel consumption; NO(x) emissions). Compared with another hydropower studies, the LCI showed magnitude adequacy, with better results than small hydropower, which reveals a scale economy for material and energy exchanges in the case of ltaipu Power Plant. (C) 2009 Elsevier Ltd. All rights reserved.

A linearly tunable low-voltage CMOS transconductor with improved common-mode stability and its application to (gm)-C filters

A linearly tunable low-voltage CMOS transconductor featuring a new adaptative-bias mechanism that considerably improves the stability of the processed-signal common,mode voltage over the tuning range, critical for very-low voltage applications, is introduced. It embeds a feedback loop that holds input devices on triode region while boosting the output resistance. Analysis of the integrator frequency response gives an insight into the location of secondary poles and zeros as function of design parameters. A third-order low-pass Cauer filter employing the proposed transconductor was designed and integrated on a 0.8-mum n-well CMOS standard process. For a 1.8-V supply, filter characterization revealed f(p) = 0.93 MHz, f(s) = 1.82 MHz, A(min) = 44.08, dB, and A(max) = 0.64 dB at nominal tuning. Mined by a de voltage V-TUNE, the filter bandwidth was linearly adjusted at a rate of 11.48 kHz/mV over nearly one frequency decade. A maximum 13-mV deviation on the common-mode voltage at the filter output was measured over the interval 25 mV less than or equal to V-TUNE less than or equal to 200 mV. For V-out = 300 mV(pp) and V-TUNE = 100 mV, THD was -55.4 dB. Noise spectral density was 0.84 muV/Hz(1/2) @1 kHz and S/N = 41 dB @ V-out = 300 mV(pp) and 1-MHz bandwidth. Idle power consumption was 1.73 mW @V-TUNE = 100 mV. A tradeoff between dynamic range, bandwidth, power consumption, and chip area has then been achieved.

Biological aspects of Orius insidiosus (Say) feeding on eggs of Plutella xylostella (Linnaeus) and Anagasta kuehniella (Zeller).

The objective of this work was to evaluate the biology of Orius insidiosus fed on eggs of Plutella xylostella and Anagasta kuehniella. The eggs used were obtained from the Laboratorio de Biologia e Criacao de Insetos, Departamento de Fitossanidade, FCAV/UNESP. The experiment was carried out with a total of 50 12-to-24-hour-old O. insidiosus nymphs, 1 per Petri dish (50 replications). P. xylostella or A. kuehniella eggs were places into each Petri dish daily, along with a small cotton pad moistened with distilled water. The evaluations were carried out daily. The adults were separated in couples, and placed in Petri dishes. The following biological aspects were evaluated: duration, survival rate and consumption of the nymph instars and of the nymph period; longevity of males and females; consumption per day and adult longevity; eggs per day; female fecundity; egg viability; embryonic period; preoviposition period, oviposition period, post-oviposition period. The fertility life table parameters were also evaluated. The predator O. insidiosus did not present significant differences for its biological characteristics, when feeding on P. xylostella and A. kuehniella eggs, however it showed improved fertility life table parameters when fedo n eggs of P. xylostella, suggesting the possibility of using these eggs in the mass rearing of this insect.