Efeitos da injunção da base nas orientações interior e exterior e nas coordenadas do espaço objeto em imagens obtidas com a estéreo vídeo-câmara de um sistema móvel de mapeamento

In general, a land-based mobile mapping system is featured by a vehicle with a pair of video cameras mounted on the top and positioning and navigation sensors loaded in the vehicle. Considering the pair of video cameras mounted on the roof of the vehicle as a stereo camera pointing forward with both optical axes parallel to each other and orthogonal to the stereo base, whose length is 0.94 m, this paper aims at analyzing the interior and exterior camera orientation and the object point coordinates estimated by phototriangulation when the length constraint related to the stereo base is considered or not. The results show that the stereo base constraint has effect ouver the convergence estimation, but does it neither improves the object point coordinate estimation at significance level of 5% and nor it influences the interior orientation parameters. Finally, it has been noticed that the optical axes are not truly parallel to each other and orthogonal to the stereo base. Additionally, it has been observed that there is a convergence of approximately 0.5 degrees in the optical axes and they are not in the same plane (approximately 0.8 degrees deviation).

Respirometric techniques for assessment of biological kinetics in constructed wetland

The aim of this research was the development of a procedure to measure biological kinetics of organic matter oxidation and nitrification in constructed wetland, by using respirometric techniques. Columns simulating cores of vertical subsurface flow systems were investigated. The oxygen uptake rate (OUR) of the columns was calculated on the basis of the difference of DO concentrations measured continuously at the top and at the bottom of the column. From the respirogram, the following kinetic parameters have been evaluated: maximum rate of oxidation of readily biodegradable COD, maximum rate of nitrification, endogenous respiration of the biomass grown inside the bed. In order to improve the interpretation of the respirograms, additional respirometric tests were carried out on the wetland columns by using pure substrates, such as acetate (carbon source) and ammonium (substrate for nitrification). The kinetic parameters obtained from respirograms can be useful for control and design of constructed wetlands or for improving nutrient and carbon mass balances.

The Hunt for New Physics at the Large Hadron Collider

The Large Hadron Collider presents an unprecedented opportunity to probe the realm of new physics in the TeV region and shed light on some of the core unresolved issues of particle physics. These include the nature of electroweak symmetry breaking, the origin of mass, the possible constituent of cold dark matter, new sources of CP violation needed to explain the baryon excess in the universe, the possible existence of extra gauge groups and extra matter, and importantly the path Nature chooses to resolve the hierarchy problem - is it supersymmetry or extra dimensions. Many models of new physics beyond the standard model contain a hidden sector which can be probed at the LHC. Additionally, the LHC will be a. top factory and accurate measurements of the properties of the top and its rare decays will provide a window to new physics. Further, the LHC could shed light on the origin of neutralino masses if the new physics associated with their generation lies in the TeV region. Finally, the LHC is also a laboratory to test the hypothesis of TeV scale strings and D brane models. An overview of these possibilities is presented in the spirit that it will serve as a companion to the Technical Design Reports (TDRs) by the particle detector groups ATLAS and CMS to facilitate the test of the new theoretical ideas at the LHC. Which of these ideas stands the test of the LHC data will govern the course of particle physics in the subsequent decades.

Search for charge-asymmetric production of W ' bosons in t(t)over-bar + jet events from pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Controle estatístico aplicado ao processo de colheita mecanizada de cana-de-açúcar

O avanço da mecanização na colheita da cana-de-açúcar (Saccharum spp.) proporcionou o uso de novas tecnologias e ganho em produtividade para a cultura. O controle da qualidade do processo de colheita da cana-de-açúcar é fundamental para reduzir as perdas. Este trabalho teve o objetivo de avaliar as perdas na colheita mecanizada de cana-de-açúcar, utilizando-as como indicadores de qualidade do processo de colheita. Os dados foram coletados em duas propriedades próximas a Jaboticabal - SP, com a variedade SP80-3280, em 3º e 4º cortes. Caracterizou-se o porte do canavial e, após a colheita, demarcou-se área de 1,5 ha, sendo demarcados 25 pontos, espaçados de 12 x 50 m, quantificando-se as perdas visíveis. Posteriormente, foi aplicado o controle estatístico do processo pela média, que consta de três vezes o desvio-padrão para mais ou para menos, sendo esses os limites superior e inferior de controle, respectivamente. A média das perdas de pedaço solto foi estatisticamente maior do que as médias de perdas em pedaço fixo, cana inteira, cana-ponta e toco. A ocorrência de perdas em rebolo estilhaçado foi menor para o 4º corte em relação ao 3º corte, enquanto as perdas em pedaço fixo e toco foram menores no 3º corte, comparadas às perdas no 4º corte. em cada corte, as médias para as perdas totais estiveram próximas dos valores encontrados na bibliografia. Pedaço solto foi a variável de perdas visíveis com maior percentagem de ocorrência. As perdas demonstraram que a colheita mecanizada não se encontra sob controle estatístico de processo.

Diagnose foliar da gravioleira (Annona muricata L.): efeito da posição de ramos e folhas

A carência de informações na literatura sobre a amostragem de folhas da gravioleira, particularmente, a definição da posição da folha na copa das árvores e das folhas nos ramos ainda é um fator limitante para a diagnose foliar dessa cultura. Objetivando determinar a parte da planta indicada para a amostragem de folhas e a avaliação do estado nutricional da gravioleira conduziu-se um experimento no Campo Experimental da Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA) Agroindústria Tropical, em Pacajus (CE), no período de março a abril de 2003. Colheram-se folhas de três posições da copa (terço superior, terço médio e terço inferior) e três posições no ramo (folhas da parte apical, mediana e basal) e determinaram-se os teores de P, K, Ca, Mg, S, Fe, Cu, Zn e Mn. Os resultados permitem sugerir que os teores de minerais das folhas da parte mediana da copa das árvores e na posição mediana do ramo refletem melhor o estado nutricional da frutífera.

Desempenho das metodologias convencionais de quantificacao de reservas<>9d\estudo de um deposito de niquel

Ten working-groups were formed for estimation of nickel ore reserves, associated to an ultrabasic body, at Ipanema, MG. Each group employed six methods: parallel sections, isolines, triangles, polygons, blocks and statistical method. The triangles method showed more variability, and the smallest dispersion was obtained by the polygons method; the other methods induced fluctuations in relation to the mean. Top and bottom ore irregularities produced difficulties in the performance of the parallel sections method. Different ways of application of isolines method also produced some variations. Excepting for few calculated data, the overall results are very close to 2 200 000 t or ore. -English summary

Influence of thermal treatments in the corrosion behaviour of HVOF Cr 3C2-NiCr coatings

Thermal spray coatings as Cr3C2-NiCr obtained by high velocity oxy-fuel spraying (HVOF) are mainly applied due to their behaviour against aggressive erosive-abrasive and corrosive atmospheres and their thermal stability at high temperatures [1]. In order to increase the corrosion protection that it offers to the substrate trying to close the interconnected pores, it is possible to apply a thermal treatment with the gun during the spraying of the coating. This treatment could be applied in different ways. One of these ways consists of spraying only a few layers of coating followed by thermal treatment and finally the spray of the rest of layers. This thermal treatment on spraying is studied related to the corrosion properties of the system. The study comprises the electrochemical characterisation of the system by open circuit potential (OC), polarisation resistance (Rp), cyclic voltammetry (CV) and impedance spectroscopy measurements (EIS). Optical and scanning electron microscopy characterisation (OM and SEM) of the top and cross-section of the system has been used in order to justify the electrochemical results.

Influence of light curing source on microhardness of composite resins of different shades

Introduction: The evolution of light curing units can be noticed by the different systems recently introduced. The technology of LED units promises longer lifetime, without heating and with production of specific light for activation of camphorquinone. However, further studies are still required to check the real curing effectiveness of these units. Purpose: This study evaluated the microhardness of 4 shades (B-0.5, B-1, B-2 and B-3) of composite resin Filtek Z-250 (3M ESPE) after light curing with 4 light sources, being one halogen (Ultralux - Dabi Atlante) and three LED (Ultraled - Dabi Atlante, Ultrablue - DMC and Elipar Freelight - 3M ESPE). Methods: 192 specimens were distributed into 16 groups, and materials were inserted in a single increment in cylindrical templates measuring 4mm x 4mm and light cured as recommended by the manufacturer. Then, they were submitted to microhardness test on the top and bottom aspects of the cylinders. Results: The hardness values achieved were submitted to analysis of variance and to Tukey test at 5% confidence level. It was observed that microhardness of specimens varied according to the shade of the material and light sources employed. The LED appliance emitting greater light intensity provided the highest hardness values with shade B-0.5, allowing the best curing. On the other hand, appliances with low light intensity were the least effective. It was also observed that the bottom of specimens was more sensitive to changes in shade. Conclusion: Light intensity of LED light curing units is fundamental for their good functioning, especially when applied in resins with darker shades.

Facies sedimentares e ambientes deposicionais da Formação Barbalha no vale do cariri, bacia do araripe, nordeste do Brasil

The Aptian Barbalha Formation represents the first unit of the post-rift sequence of the Araripe Basin and crops out at the slopes of the Aranpe plateau in the eastern part ot Aranpe Basin. The unit has also been named Kio da Batateira Formation, but this name is here used in its original definition as Batateira Beds, an interval of great lateral continuity and characterized by the presence of bituminous shales of the Alagoas Stage (P-270 palynological biozone). This paper presents the results of a stratigraphic analysis carried out along the outcrop belt in order to establish the facies architecture and to interpret deposicional environments of the siliciclastic Barbalha Formation. Detailed stratigraphic vertical sections were measured and correlated. They allowed the recognition of two depositional sequences characterized by fining upward arrangement of facies, beginning with fluvial deposits and ending with lacustrine deposits at their tops. The end of the first cycle is represented by black shales and brecciated limestones of the Batateira Beds that record a geologic event of regional magnitude and serve as meaningful long-distance stratigraphic mark. The second deposicional sequence overlies disconformably the Batateira Beds and begins with clast-supported conglomerates, which are covered by a succession of fluvial sandstones and minor intervals of pelitic rocks. The sandstone content diminishes towards the top and the upper part of the unit is characterized by the presence of ostracode-rich green shales. The Barbalha Formation is conformably overlaid by Late Aptian lacustrine limestones belonging to the Crato Member of the Santana Formation.

Influência da composição de resinas compostas no grau de conversão e degradação hidrolítica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação de LEDs de alta intensidade quanto à eficiência de polimerização de resina composta e variação de temperatura na dentina bovina

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da microdureza superficial da resina composta fotopolimerizada por aparelho de luz halógena e de diodo(LED) em função de opacidade e ação do flúor fosfato acidulado

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da temperatura sobre a microdureza de uma resina composta fotoativada com luz halógena e Leds

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação da dureza e do grau de conversão de uma resina composta em função do pré-tratamento térmico e da fonte de luz fotopolimerizadora

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)