An investigation of electrolytic surface damages and electroplated crhomium effects on fatigue behavior of high strength steel

Fatigue crack initiation occurs at the surface, although sub surface nucleation has also been reported. Localized imperfections like inclusions close to surface and surface small pits can result in crack sources. Coatings are not always beneficial by fatigue point of view too. Mechanical properties of the covering material can change considerably the fatigue behavior of base metal due to residual surface stresses, to micro cracks or to hydrogen embrittlement. This paper is concerned with analysis of electrolytic etch on the fatigue resistance of a 35NCD16 high strength steel in a mechanical condition of (1760 - 1960) MPa, and analysis of electroplated hard chromium effects on the fatigue resistance in a strength condition of 989 MPa. Hardness impression was used as a reference parameter in case of electrolytic etch. In both cases, experimental data showed that fatigue strength of 35NCD16 steel was considerably reduced. Copyright © 2001 Society of Automotive Engineers, Inc.

Morphological aspects of the capybara stomach (Hydrochaeris hydrochaeris): Gross and microscopic structure

The digestive system of the capybara has been investigated because of its coprofagia habits, important for their absorptive activity. These species present differences in terms of gastrointestinal morphological characters when compared with other rodents. Macroscopiclly, the stomach of the capybara is constituted of the following parts: cardiac, pyloric, body, fundic and gastric diverticulum. It presents two curvatures, one big and another small. Externally, the presence of gastric bands (tenias) is observed. With regards to the volumetric view, the gastric capacity varies from 850 to 2010 ml, with an average of 1498.57 ml. So, the stomach of this animal can be classified as a simple stomach, in the format of a curved sack and similar to an inverted letter 'J'. The gastric mucous membrane presents a surface filled by numerous tortuous gastric folds and longitudinally distributed along all its extension. The mucous tunic also possesses recesses located among the successive gastric folds, which were denoted as gastric parts with numerous openings described as gastric pits. In the cardiac part, a glandular epithelium with cardiac glands is noticed containing a lot of parietal and mucous neck cells. The fundic part, body and gastric diverticulum contain proper gastric glands with main, parietal and mucous neck cells. Finally, the pyloric part has pyloric glands with two cellular types, mucous neck and parietal cells.

Caracterização morfológica da corrosão por pite da liga AL2024 em soluções contendo cloretos e molibdatos

A very new method application for digital image processing and analysis to classify shape and evaluate size and morphology parameters of pit corrosion is used in this paper. This method seems to be very effective to analysis surfaces with low or high degree of pitting formation. Pits formed on 2024 alloy surface by chloride and by chloride + molibdate anions have similar mean area, are found to be widther than deeper and exhibit predominantly conical or near-conical and irregular geometries.

Estudo das características morfológicas dos pites nos materiais resistentes à corrosão

This paper has as a purpose a new alternative technique development to characterize pitting corrosion evolution, aiming classification, size and determination of morphological parameters which rule pits increase. In this case, the method will be applied to the 304 ABNT stainless steel, thermally treated and exposed to different times in salt spray. Different 304 steel conditions, rolled and thermally treated have exhibited similar geometry, predominantly conic, near-conic and irregular pits. On rolled steel, pits width increases faster than height; however, on thermally treated steel, pits are found to increase in height.

Influence of chromate, molybdate and tungstate on pit formation in chloride medium

It has been characterized and evaluated the 2024-T351 and 7050-T7451 aluminum alloys pitting corrosion in naturally aerated chloride aqueous solutions containing chromate, molybdate and tungstate. It has been carried out electrochemical and non-electrochemical immersion corrosion tests accompanied by surface metallography analysis using an optical microscopy. Chromate for the two alloys and in molybdate for 7050 has corrosion inhibiting effects, whereas tungstate promotes the pitting corrosion for these alloys. Quantitative surface analysis upon the alloys after immersion has indicated that pits are predominantly conical or quasi-conical and irregular. In general, pits have been wider than deep and the widest have been also the deepest. Despite inhibitor presence, when pits have been nucleated, they grow with the same intensity. © 2005 Elsevier B.V. All rights reserved.

Longitudinal photographic observation of the occurrence of bubbles in pit and fissure sealants

The purpose of this study was to employ photographic evaluation to observe the presence or absence of bubbles in pit and fissure sealants Concise and Prisma Shield, at 7 days, 18 months, 36 months and 11 years after accomplishment of treatment. Methods: A hematoxylin-based staining solution was applied to the occlusal surface at the study periods, which allowed assessment of the sealing material on the surface. All occlusal surfaces were photographed and the photographs corresponding to each period were subjected to photographic evaluation. Results: There was statistically significant difference only at 18 months, with a significantly higher number of specimens with bubbles for the Prisma Shield sealant compared to the Concise, whereas the groups were similar at all other study periods. On the other hand, separate analysis of subsequent periods of the sealants did not reveal any significant difference. Conclusions: According to the results of the present longitudinal investigation, it may be concluded that the sealing materials showed that bubbles came into and went out with time. However, this fact did not interfere with its clinical purpose, provided the remaining material covers the expected region of pits and fissures.

Ultrastructural features of the lining epithelium of the vas deferens of Agouti paca

The epididymal epithelium of Agouti paca, a wild South American rodent, was basically formed by principal and basal cells. Principal cells were closely related to processes of adsorptive endocytosis, phasefluid endocytosis and also secretion originating from their cytoplasmic ultrastructural features. Principal cells were also characterized by the presence of vesicles of several shapes, sizes and internalized content occurring in smaller pits, pale small vesicles next to the apical brush border of microvillus, as well as coated vesicles, smooth surface vesicles and great vesicles. Multivesicular bodies, endosomes and lysosomes were mainly observed in supranuclear position. Moreover, presence of an apocrine secretory process was demonstrated by the occurrence of apical cytoplasmic expansions projecting into the vas deferens luminal compartment. Basal flattened cells without luminal surface contact occurred next to the basement membrane of the ductus, and did no exhibit special ultrastructural features.

Additional observations on the gross morphology and microstructure of Baccaconularia Hughes, Gunderson et Weedon, 2000, a Cambrian (Furongian) conulariid from the north-central USA

Baccaconularia Hughes, Gunderson et Weedon, 2000, from the Furongian Series (Cambrian System) of the north-central USA, has been interpreted as a conulariid cnidarian, based on a suite of gross morphological similarities shared only with other post-Cambrian genera currently assigned to this group. Closely spaced, squarish to subrectangular facial nodes of Baccaconularia are aligned in distinct longitudinal files. Nodes also display a subtler, more or less rectilinear transverse alignment, though this pattern commonly is disrupted by offset parallel to the longitudinal files. In their shape and pattern of arrangement, the nodes of Baccaconularia are most similar to the squarish to elongate nodes of Pseudoconularia Bouček, 1939. Longitudinal node files of Baccaconularia may also be compared with the longitudinal facial ridges of Conularia cambria Walcott, 1890 from the Furongian of Wisconsin. Apical angles of Baccaconularia range from approximately 13° to 14.5°. Scanning electron imaging of B. cf. robinsoni shows that its thin, phosphatic skeleton is finely lamellar, with the thickness of individual lamellae measuring approximately 1 μm. The skeleton also exhibits microscopic circular pores and crater-like pits that range from approximately 5 to 10 μm in diameter. These pores and pits are similar in size, geometry, areal density and pattern of arrangement to those of many post-Cambrian conulariids. Microscopic circular pores are documented here for the first time in the genus Archaeoconularia Bouček, 1939 from the Upper Ordovician of the Czech Republic. Although the origin of the pores and pits is open to alternative interpretations, the discovery of these features and fine lamination in Baccaconularia strengthens the argument that this genus is a Cambrian conulariid. © 2006 Nanjing Institute of Geology and Palaeontology, CAS.

Measurement of sealant surface area by clinical/computerized analysis: 11-year results.

OBJECTIVE: To analyze the clinical behavior of 2 pit and fissure sealants through clinical/computerized evaluation. METHOD AND MATERIALS: Occlusal sealants were placed on maxillary and mandibular first and second premolars according to a split-mouth design. All premolars were sealed with either Concise (3M Espe) or Prisma Shield (Caulk/Dentsply) sealant agents. A hematoxylin-based staining solution was applied on the occlusal surface 7 days, 18 months, 36 months, and 11 years after occlusal sealing to allow checking of the sealant material on the surface. At each analysis time all occlusal surfaces were photographed, and the photographs corresponding to each time period were analyzed with SigmaScan 4.0 Software. The alterations of the sealed area of each sealant were analyzed with the software and recorded. Next, the measurements of the areas were tabulated and analyzed according to each period. Analysis of variance (ANOVA), with parts subdivided into time, and the t test, with a significance level of 5%, were used. RESULTS: The greatest sealed area was maintained by the sealant Concise. However, over the course of 11 years, all sealants began to show the same level of alteration in sealed area. CONCLUSION: The sealing materials showed alteration in sealed area over time, but they were efficient in controlling caries lesion formation on premolar pits and fissures.

Scientific article in vitro evaluation of the influence of air abrasion on detection of occlusal caries lesions in primary teeth

The purpose of this study was to assess the influence of cleaning pits and fissures with an aluminum oxide air abrasion system on the detection of occlusal caries in primary teeth using laser fluorescence (LF) and visual examination. Methods: The sample comprised 65 pit and fissure sites on extracted primary teeth suspected to be carious. The sites were submitted to 2 visual examinations (examiner JAR) and 2 LF readings (examiner TMV). Next, the occlusal surfaces were air-abraded and re-examined thereafter using both methods. The teeth were sectioned, and the histological analysis of the sites with a stereoscopic magnifying lens at X32 magnifi cation was used as the gold standard. Results: Cohen's kappa statistic for LF and visual examination were, respectively, 0.282/0.884 before and 0.896/0.905 after air abrasion. LF showed a sensitivity of 0.28 increasing to 0.49 and a specifi city of 0.50 increasing to 0.92. Visual examination showed sensitivity of 0.78 and specifi city of 0.73. Both increased after air abrasion. Conclusion: The findings suggest that cleaning pits and fissures with aluminum oxide air abrasion increased the accuracy of LF and visual examination for detection of occlusal caries in primary teeth.

Description of eggs and nymphal instars of Triatoma baratai Carcavallo and Jurberg, 2000 based on optical and scanning electron microscopy (Hemiptera: Reduviidae: Triatominae)

Triatoma baratai Carcavallo & Jurberg, is a wild (i.e., nonperidomestic) species found in the State of Mato Grosso do Sul (Bodoquena region, county of Bonito), Brazil. Its eggs and nymphs are described here based on optical and scanning electron microscopy. The operculum and exochorion have pentagonal, hexagonal, and heptagonal cells, with small cracks and small random pits. Differences in the eggs and five nymphal instars of T. baratai allow them to be distinguished from the sympatric species Triatoma williami Galvão, Souza & Lima, and from six of the nine members of the Triatoma oliveirai complex. The most useful differentiating characters are in the color, shape of the abdomen, head, and total body length. Keys are provided to separate the eggs and nymphal instars of six of the nine members of the Triatoma oliveirai species complex. Copyright ©2009 Magnolia Press.

Streptococcus mutans attachment on a cast titanium surface

This study examined by means of scanning electron microscopy (SEM), the attachment of Streptococcus mutans and the corrosion of cast commercially pure titanium, used in dental dentures. The sample discs were cast in commercially pure titanium using the vacuum-pressure machine (Rematitan System). The surfaces of each metal were ground and polished with sandpaper (#300-4000) and alumina paste (0.3 μm). The roughness of the surface (Ra) was measured using the Surfcorder rugosimeter SE 1700. Four coupons were inserted separately into Falcon tubes contained Mueller Hinton broth inoculated with S. mutans ATCC 25175 (109 cuf) and incubated at 37 °C. The culture medium was changed every three days during a 365-day period, after which the falcons were prepared for observations by SEM. The mean Ra value of CP Ti was 0.1527 μm. After S. mutans biofilm removal, pits of corrosion were observed. Despite the low roughness, S. mutans attachment and biofilm formation was observed, which induced a surface corrosion of the cast pure titanium.

Análise geoambiental da região de marília, SP: Suscetibilidade a processos erosivos frente ao histórico de ocupação da área

The study area comprises the western portion of the Marília Plateau, State of São Paulo, southeastern Brazil. The geological substrate encompasses Cretaceous sedimentary rocks of the Bauru Group and local Neocenozoic units like colluvium aprons, fluvial terrace deposits, in situ regoliths, and modern alluvial deposits. In a geomorphologic sense, the study area might be characterized as showing two main pediplanes, viz. P1 Surface (upper) and P2 Surface (lower), both surfaces are presently under dissecation processes. After the 1920's the expansion of the railroad system fostered the removal of the natural vegetation, which in turn was followed by the introduction of coffee, peanut, corn and cotton crops. This intense exploitation was conducted without respect to the soil carrying capacity and its natural susceptibility to erosional processes, including an aggressive form known as voçoroca. As a result, the study shows that the most susceptible material includes colluvium aprons, in situ regoliths, and colluvium-alluvium or alluvium deposits. The most critical situation is in the P2 Surface context, near the bottom of the Marília Plateau scarpment, where surface runoff can be very strong. Another point of active erosion is represented by the exposed walls of gullies and voçorocas, mainly in fluvial reaches subjected to talweg lowering. In a general sense, this study shows current evidence of erosional stability due to the ìntroduction of pastures as a predominant type of land occupation and to a series of erosion control procedures. Among these actions are terrace implantation, construction of small pits for runoff control, natural or induced reforestation by land owners. Despite these efforts, some erosion points remain chiefly in steeper country roads and trail stretches, in areas of concentration of cattle tracks (e.g., near cattle ponds), gullies or voçorocas exposed walls, and badly planned urbanization. The permanence of these erosion points demonstrates the necessity of a continuous monitoring of surface dynamics as well as a rapid and effective intervining measures of erosion and/or silting control.

Alterações hidrogeomorfológicas devido à dinâmica de uso da terra na Bacia Hidrográfica do Ribeirão Santa Gertrudes (SP)

Agricultural and mining activities are directly related to changes in natural landscapes. From the perspective of anthropogenic geomorphology supported by general systems theory, this research has developed, in order to identify and analyze changes in the land use, mainly from agriculture and the exploitation of clay, and its implications in the hydro-geomorphological characteristics in the Santa Gertrudes Stream watershed (SP). This area is within the context of the Ceramic Pole Santa Gertrudes (SP), which besides its importance as a supplier of raw material, is characterized as the largest center of international reference in ceramic tiles on the American continent. For this purpose, we made land use and geomorphology maps of two scenarios, corresponding to the years 1962 and 2006, which allowed the identification of changes caused by human activities on the landforms of the area, such as the increase in area of parcels intended for mining activity, which went from 3.1% to occupy 19% of the catchment area of the respective period and that, among other changes, gave rise to new forms of relief as, for example, in levels of pit mining abrupt and smooth. The results indicate that the main features of representative of human changes in relief are represented for opening of large clay mining pits and agricultural activities, which intensified the denudation and sedimentation processes in the Santa Gertrudes Stream watershed.

Effect of different pre-irradiation times on curcumin-mediated photodynamic therapy against planktonic cultures and biofilms of Candida spp

Objectives: The aim of this study was to evaluate the effects of pre-irradiation time (PIT) on curcumin (Cur)-mediated photodynamic therapy (PDT) against planktonic and biofilm cultures of reference strains of Candida albicans, Candida glabrata and Candida dubliniensis. Materials and methods: Suspensions and biofilms of Candida species were maintained in contact with different concentrations of Cur for time intervals of 1, 5, 10 and 20 min before irradiation and LED (light emitting diode) activation. Additional samples were treated only with Cur, without illumination, or only with light, without Cur. Control samples received neither light nor Cur. After PDT, suspensions were plated on Sabouraud Dextrose Agar, while biofilm results were obtained using the XTT-salt reduction method. Confocal Laser Scanning Microscopy (CLSM) observations were performed to supply a better understanding of Cur penetration through the biofilms after 5 and 20 min of contact with the cultures. Results: Different PITs showed no statistical differences in Cur-mediated PDT of Candida spp. cell suspensions. There was complete inactivation of the three Candida species with the association of 20.0 μM Cur after 5, 10 and 20 min of PIT. Biofilm cultures showed significant reduction in cell viability after PDT. In general, the three Candida species evaluated in this study suffered higher reductions in cell viability with the association of 40.0 μM Cur and 20 min of PIT. Additionally, CLSM observations showed different intensities of fluorescence emissions after 5 and 20 min of incubation. Conclusion: Photoinactivation of planktonic cultures was not PIT-dependent. PIT-dependence of the biofilm cultures differed among the species evaluated. Also, CLSM observations confirmed the need of higher time intervals for the Cur to penetrate biofilm structures. © 2012 Elsevier Ltd. All rights reserved.