Surface characterization of feldspathic ceramic using ATR FT-IR and ellipsometry after various silanization protocols

Objectives. This study characterized the feldspathic ceramic surfaces after various silanization protocols.Methods. Ceramic bars (2 mm x 4 mm x 10 mm) (N = 18) of feldpathic ceramic (VM7, VITA Zahnfabrik) were manufactured and finished. Before silane application, the specimens were ultrasonically cleaned in distilled water for 10 min. The ceramic specimens were randomly divided into nine groups (N = 2 per group) and were treated with different silane protocols. MPS silane (ESPE-Sil, 3M ESPE) was applied to all specimens and left to react at 20 degrees C for 2 min (G20). After drying, the specimens were subjected to heat treatment in an oven at 38 degrees C (G38), 79 degrees C (G79) or 100 degrees C (G100) for 1 min. Half of the specimens of each group were rinsed with water at 80 degrees C for 15 s (G20B, G38B, G79B, G100B). The control group (GC) received no silane. Attenuated total reflection infrared Fourier transform analysis (ATR FT-IR) was performed using a spectrometer. Thickness of silane layer was measured using a spectroscopic ellip-someter working in the lambda = 632.8 nm (He-Ne laser) at 70 degrees incidence angle. Surface roughness was evaluated using an optical profilometer. Specimens were further analyzed under the Scanning Electron Microscopy (SEM) to observe the topographic patterns.Results. ATR FT-IR analysis showed changes in Si-O peaks with enlarged bands around 940 cm(-1). Ellipsometry measurements showed that all post-heat treatment actions reduced the silane film thickness (30.8-33.5 nm) compared to G20 (40 nm). The groups submitted to rinsing in hot water (B groups) showed thinner silane films (9.8-14.4 nm) than those of their corresponding groups (without washing) (30.8-40 nm). Profilometer analysis showed that heat treatments (Ra approximate to 0.10-0.19 mu m; Rq approximate to 0.15-0.26 mu m) provided a smoother surface than the control group (Ra approximate to 0.48 mu m; Rq approximate to 0.65 mu m). Similar patterns were also observed in SEM images.Significance. Heat treatment after MPS silane application improved the silane layer network. Rinsing with boiling water eliminated the outmost unreacted regions of the silane yielding to thinner film thicknesses. (C) 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

The adhesive system and root canal region do not influence the degree of conversion of dual resin cement

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of Hg in water by CVAAS using 2-aminothiazole modified silica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Emprego de nebulizador pneumático de ICP-MS como câmara de diluição em sistemas de injeção em fluxo para determinações multielementares

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Multivariate calibrations on H-1 NMR profiles for prediction of physicochemical parameters of Brazilian commercial gasoline

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Essential oil of Lithraea molleoides (Vell.): chemical composition and antimicrobial activity

Lithraea molleoides(Vell.) (Anacardiaceae) é uma árvore encontrada no Brasil, Paraguai, Bolívia, Uruguai, Argentina e Chile. É popularmente usada na forma de extrato alcoólico, decocção e infusão para o tratamento de tosse, bronquite, artrite, doenças do sistema digestivo, como diurético, tranqüilizante, hemostático e tônico. O objetivo do presente estudo foi a extração do óleo essencial dos frutos maduros, folhas e outras partes aéreas da planta e o rendimento do mesmo; a identificação e quantificação dos principais componentes e a determinação da atividade antimicrobiana. O rendimento do óleo essencial dos frutos maduros foi de 1%, entretanto, não foi encontrado óleo essencial nas partes aéreas da planta. A análise do óleo essencial por cromatografia gasosa com espectrometria de massa, mostrou a presença de limoneno (89,89%), alfa-pineno (3,48%), beta-pineno (2,63%), alfa-terpineol (1.27%), mirceno (0,64%), sabineno (0,54%), 4-terpineol (0,28%), canfeno (0,22%) e delta-3-careno (0,13%). O óleo essencial foi ativo contra algumas bactérias Gram positivas e leveduras testadas e não apresentou atividade contra bactérias Gram negativas.

Composição química e produtividade dos principais componentes do óleo essencial de Baccharis dracunculifolia DC. em função da adubação orgânica

Objetivou-se avaliar a composição química e produtividade dos principais componentes do óleo essencial de Baccharis dracunculifolia DC. em função de doses de composto orgânico (0, 10, 20, 30, 40 e 50 t ha-1). Foi realizada uma colheita, aos 150 dias após o transplante das mudas. O óleo essencial, da massa seca útil da parte aérea, foi extraído por hidrodestilação e analisado em cromatógrafo a gás acoplado a espectrômetro de massas (Shimadzu, QP-5000). A identificação dos constituintes químicos foi realizada através da análise comparativa dos espectros de massas das substâncias com o banco de dados do sistema CG-EM (Nist 62.lib), literatura e índice de retenção. Os resultados foram submetidos à análise de variância pelo teste F, às médias obtidas foram submetidas à análise de regressão e o teste Tukey para o efeito das doses de composto orgânico. Os três componentes sesquiterpênicos, E-nerolidol, espatulenol e óxido de cariofileno, perfazem 58,44% da média relativa da composição química do óleo essencial de B. dracunculifolia, composto pela presença de 28 substâncias. Na produtividade dos componentes γ-muroleno, valenceno, δ-cadineno e E-nerolidol as dosagens estudadas influenciaram as plantas, que na dosagem 30 t ha-1 obtiveram os melhores resultados. Se o objetivo no cultivo de B. dracunculifolia for o componente espatulenol as dosagens 30 e 40 t ha-1 obtiveram os melhores resultados. Para a produtividade do componente óxido de cariofileno as dosagens estudadas influenciaram as plantas, que na dosagem 40 t ha-1 obtiveram os melhores resultados.

Conteúdo de peptídeos e avaliação morfofisiológica dos espermatozóides do epidídimo e ejaculado de bovinos

Objetivou-se com este estudo a identificação de alguns fatores protéicos envolvidos na qualidade funcional dos espermatozóides epididimais (SPZEP) e ejaculados (SPZEJ) de bovinos. Foram avaliadas as características morfofisiológicas e analisado o conteúdo peptídico destas estruturas de 11 animais mestiços Nelore, de 24 a 30 meses de idade. As avaliações morfofisiológicas foram motilidade progressiva (MOT, %), vigor, patologias espermáticas, integridade acrossômica e da cromatina. Foi observado que, os SPZEJ, na média, apresentaram MOT maior do que os SPZEP, 72,3 e 46,4%, respectivamente. Considerando as patologias espermáticas, taxas de defeitos maiores (DEFMAI), menores (DEFMEN) e totais (DEFTOT), houve diferença significativa entre as taxas dos DEFMEN e DEFTOT dos SPZEP e SPZEJ, sendo, em média, 91,1 e 8,5% e 95,4 e 11,8%, respectivamente. As taxas dos DEFMEN e DEFTOT dos SPZEP foram maiores em função da presença de espermatozóides com gotas citoplasmáticas distais. A análise das protéinas dos SPZEP e SPZEJ foi realizada por espectrometria de massa, método MALDI-TOF (matrix -assisted laser desorption/ionization - time of flight), e revelou presença de peptídeos de massa molecular variando de 1,1 a 26,3 kDa nos SPZEJ e de 1,1 a 11,6 kDa nos SPZEP. Foram identificados peptídeos de 10,6 e 13,4 kDa somente nos SPZEJ e de 6,8 kDa somente nos SPZEP. Foi observada relação do peptídeo de massa molecular de 7,4 kDa dos SPZEP e de 4,7 kDa dos SPZEJ, com a MOT Ê 80%, destas estruturas. Os resultados sugerem o envolvimento destes peptídeos nos processos funcionais das células espermáticas do epidídimo e ejaculado. O estudo utilizou o método MALDI/TOF para espectrômetro de massa, para identificar peptídeos em espermatozóides do epidídimo de bovinos, pela primeira vez no País.

Hydroxymethylnitrofurazone:Dimethyl-beta-cyclodextrin Inclusion Complex: A Physical-Chemistry Characterization

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of modifiers on thermal behaviour of Se in acid digestates and slurries of vegetables by graphite furnace atomic absorption spectrometry

The influence of sample preparation strategy of vegetables on the electrothermal behaviour of Se without and with chemical modifiers such as Pd(NO3)(2), Pd(NO3)(2) + Mg(NO3)(2), Pd(NO3)(2) + Cd(NO3)(2), pre-reduced Pd, Mg(NO3)(2), and Ni(NO3)(2) was investigated. Acid digestates and slurries of vegetables (0.1% m/v in 1% m/v HNO3 + 0.005% v/v of Triton X-100) were used to prepare reference solutions or slurries. For 10 mul of each modifier tested, pyrolysis and atomization temperatures were evaluated using pyrolysis and atomization curves, respectively. Best conditions, such as thermal stability, signal profile, repeatability and sensitivity were attained using Pd(NO3)(2) as chemical modifier. The following heating program (temperature, ramp/hold time) of the graphite tube of the Varian SpectrAA-800Z atomic absorption spectrometer was used: dry step (85 degreesC, 5/0 s; 95 degreesC, 40/0 s; 120 degreesC, 10/.5 s); pyrolysis step (1400 degreesC, 10/3s); atomization step (2200 degreesC, 1/2 s); clean step (2600 degreesC, 2/0 s). This pyrolysis temperature is 800 degreesC higher than when measuring without any modifier. For 20 muL sample volume and 10 mug Pd(NO3)(2), analytical curves in the 3.0-30 mug Se 1(-1) range were obtained. The method was applied for Se determination in acid digestates and slurries of 10 vegetable samples and one standard reference material (rice flower) and results were in agreement at 95% confidence level. Recoveries varied from 89 to 95% for spiked samples. The lifetime of the graphite tube was ca. 250 firings and the relative standard deviations (n = 12) for a typical acid digestate and slurry containing 20 mug Se 1(-1) were 3.8% and 8.3%, respectively. The limits of detection were 2.0 mug Se 1(-1) and 0.6 mug Se 1(-1) Se for digestates and slurries, respectively. (C) 2002 Elsevier B.V. Ltd. All rights reserved.

Evaluation of shear bond strength at the interface of two porcelains and pure titanium injected into the casting mold at three different temperatures

Statement of problem. Titanium has physical and mechanical properties, which have led to its increased use in dental prostheses despite casting difficulties due to high melting point and formation of oxide layers which affect the metal-ceramic bond strength.Purpose. This in vitro study evaluated the shear bond strength of the interface of 2 dental porcelains and pure titanium injected into a mold at 3 different temperatures.Material and methods. Using commercially pure (cp) titanium bars (Titanium, Grade I) melted at 1668degreesC and cast at mold temperatures of 430degreesC, 700degreesC or 900degreesC, 60 specimens were machined to 4 x 4 mm, with a base of 5 x 1 mm. The 4-mm surfaces were airborne-particle abraded with 100 mum aluminum oxide before applying and firing the bonding agent and evaluating the 2 porcelains (Triceram/Triline ti and Vita Titankeramik). Ten specimens were prepared for each temperature and porcelain combination Shear bond testing was performed in a universal testing machine, with a 500-kg load cell and crosshead speed of 0.5 mm/min. The specimens were loaded until failure. The interfaces of representative fractured specimens of each temperature were examined with a scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). Data for shear bond strength (MPa) were statistically analyzed by 2-way ANOVA and the Tukey test (alpha = .05).Results. The results showed significant differences for the metal/porcelain interaction effect (P = .0464). There were no significant differences for the 2 porcelains (P = .4250). The Tukey test showed a significant difference between the pair cp Ti 430degreesC Triceram and cp Ti 900degreesC Triceram, with respective mean values and SDs of 59.74 +/- 11.62 and 34.03 +/- 10.35 MPa.Conclusion. Triceram porcelain showed a bond strength decrease with an increase in the mold temperature for casting titanium. The highest bond strength for Vita porcelain and the best metal-ceramic interface observed with the SEM were found with the mold temperature of 700degreesC.

Determination of selenium in nutritionally relevant foods by graphite furnace atomic absorption spectrometry using arsenic as internal standard

A method has been developed for the direct determination of Se in nutritionally relevant foods by graphite furnace atomic absorption spectrometry. Tungsten/rhodium carbide coating on the integrated platform of a transversely heated graphite atomizer or W coating with co-injection of Pd(NO3)(2) were used as a permanent modifiers. Samples and reference solutions were spiked with 500 mu g L-1 As and absorbance variations due to changes in experimental conditions were minimized. For 20 mu L aqueous analytical solutions delivered into the graphite tube, analytical curves in the 5.0-40 mu g L-1 with good linear correlation were established. Pyrolysis and atomization temperatures were evaluated using pyrolysis and atomization curves, respectively. The optimized heating program (temperature, ramp time, hold time) of the graphite tube of the Perkin-Elmer SIMAA 6000 atomic absorption spectrometer was: dry steps (110 degrees C, 5 s, 10 s; 130 degrees C, 15 s, 15 s); air-assisted pyrolysis step (600 degrees C, 20 s, 40 s; 20 degrees C, 1 s, 40 s); pyrolysis step (1300 degrees C, 10 s, 20 s); atomization step (2100 degrees C, 0 s, 4 s); clean step (2550 degrees C, 1 s, 5 s). The method was applied for Se determination in coconut water, coconut milk, soybean milk, cow milk, tomato juice, mango juice, grape juice and drinking water samples and four standard reference materials and results were in agreement at 95% confidence level. The lifetime of the tube was 500 firings and the relative standard deviations of measurements of typical samples containing 25 mu gL(-1) Se were 3.0% and 6.0% (n = 12) with and without internal standardization, respectively. The limits of detection were in the 0.35 mu g L-1-0.7 mu g Se L-1 range. The accuracy of the proposed method was evaluated by an addition-recovery experiment and all recovered values were in the 98-109% range. (c) 2004 Elsevier Ltd. All rights reserved.

Response of L-alanine and 2-methylalanine minidosimeters for K-Band (24 GHz) EPR dosimetry

Minidosimeters of L-alanine and 2-methylalanine (2MA) were prepared and tested as potential candidates for small radiation field dosimetry. To quantify the free radicals created by radiation a K-Band (24 GHz) EPR spectrometer was used. X-rays provided by a 6 MV clinical linear accelerator were used to irradiate the minidosimeters in the dose range of 0.5-30 Gy. The dose-response curves for both radiation sensitive materials displayed a good linear behavior in the dose range indicated with 2MA being more radiation sensitive than L-alanine. Moreover, 2MA showed a smaller LLD (lower limit detection) value. The proposed system minidosimeter/K-Band spectrometer was able to detect 10 Gy EPR spectra with good signal-to-noise ratio (S/N). The overall uncertainty indicates that this system shows a good performance for the detection of dose values of 20 Gy and above, which are dose values typically used in radiosurgery treatments. (c) 2007 Elsevier B.V. All rights reserved.

Determination of Cd(II) and Cd-metallothioneins in biological extracts using baker's yeast and inductively coupled plasma optical emission spectrometry

The use of Saccharomyces cerevisiae as a sorbent material to separate Cd(II) and Cd-metallothionein complex (Cd-MT) has been explored. Solid-liquid phase extractions were carried out in batch mode and the main parameters of the process (pH, temperature, time of incubation, amount of biomass and analyte) were evaluated. Under optimized conditions, the yeast quantitatively retain (94 +/- 5%) the Cd(II) while 97 +/- 2% of the Cd-MT remain in the supernatant. on base of the findings of this study, a simple method is proposed to determine Cd(II) and Cd-MT in cytosols extracted from mouse kidney and crab hepatopancreas. Inductively coupled plasma optical emission spectrometry was used to quantify the analytes in solid and liquid phase. Determination of Cd in the solid phase was carried out by introducing a slurry of the yeast (0.0625 g/10 mL) directly to the inductively coupled plasma optical emission spectrometer. Mixed standards solutions, which also have been submitted to the extraction procedure, were used to quantify the analytes in the samples. Thus, matrix effects due to nebulization of the slurry were overcame. Limits of detection (3 sigma) for Cd(II) and Cd-MT were 1.5 and 1.2 mu g L-1, respectively. Relative standard deviations of signals were 4.2% for measurements in the slurry of solid phase and 2.1% for measurements in the liquid phase. Recoveries of the analytes in cytosol samples were between 76 and 114%. The concentrations of Cd(II) (2.4 +/- 0.5 mu g L-1) and Cd-MT (3.0 +/- 0.5 mu g L-1) found by using the proposed approach were close to those found by tangential-flow ultrafiltration technique (2.6 +/- 0.7 mu g L-1 for Cd(II) and 3.7 +/- 1.7 mu g L-1 for Cd-MT).

Thermal diffusivity analysis of doped poly(methyl-methacrylate) with electron donor and acceptor molecules

A computer-assisted method for analysing photoacoustic spectra has been developed in the Windows(TM) environment with the use of an easy graphical interface, the computer simulation was carried out with the aim of using the entire expression of the Rosencwaig-Gersho theory, thus permitting multiple applications. The simulation was applied to a system that mimics the electron transfer process in which the concentration of octaethylporphin donor molecules was constant whereas the concentration of duroquinone and 2,3-dichloro-5,6-dicyano-1, l-benzoquinone acceptor molecules varied. The increment of the acceptor concentration influenced the photoacoustic amplitude and phase signals. In the phase signal a significant shift to smaller values was observed, denoting a faster heat generation. The analysis of the photoacoustic signal enabled the determination of the thermal diffusivity, the result obtained through the simulation was about (7 +/- 1) x 10(-7) m(2) s(-1) indicating that changes in the photoacoustic phase signals were due to the electron transfer process rather than changes in the thermal properties of the sample.