Isochronal sintering of the blended elemental Ti-35Nb alloy

Titanium alloy parts are ideally suited for advanced aerospace systems and surgical implants because of their unique combination of high specific strength at both room temperature and moderately elevated temperature, in addition to excellent corrosion resistance. In this work, results of the Ti-35Nb alloy sintering are presented. This alloy, due to its lower modulus of elasticity and high biocompatibility, is a promising candidate for surgical and aerospace applications. Samples were produced by mixing of initial metallic hydride powders followed by uniaxial and cold isostatic pressing with subsequent densification by isochronal sintering between 700 and 1500 degrees C, in vacuum. Sintering behavior was studied by means of microscopy and density. Sintered samples were characterized for phase composition, microstructure and microbardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. Samples sintered at high temperatures display a fine plate-like a structure and intergranular P. A few remaining pores are still found, and density above 97% for specimens sintered at 1500 degrees C is reached. (c) 2007 Elsevier B.V. All rights reserved.

NiBr2 complexes with triphenylarsine oxide (Ph3AsO). Two new interesting structures

The synthesis and crystal structure of two complexes resulting from interaction between NiBr2 and triphenylarsine oxide (Ph3AsO) is described. Green and orange complexes can be obtained from the blue, probably tetrahedral complex [NiBr2(Ph3AsO)2], depending on the solvents used for recrystallization. NiBr2·4[(C6H5)3AsO]·8H2O (green): M = 1650.2, P21/c, a = 13.731(2), b = 16.267(3), c = 17.647(2) Å, β = 112.04(1)°, V = 3651.4 Å3, Z = 2, Dx = 1.501 g cm-3, CuKα, λ = 1.54184 Å, μ = 38.67 cm-1, R = 0.039, 3741 unique reflections, 3203 with I > 3σ(I). NiBr2·4[(C6H5)3AsO]·3|2(C6H5CH3)·H2O (orange): M = 1663.7, P1, a = 12.647(8), b = 13.953(5), c = 22.853(6) Å, α = 90.91(3), β = 96.70(4), γ = 111.16(4)°, V = 3727.4 Å3, Z = 2, Dx = 1.482 g cm-3, MoKα, λ = 0.71073 Å, μ = 30.48 cm-1, R = 0.087, 8600 unique reflections, 4293 with I > 3σ(I). In the green complex the Ni(II) ion is sited on a center of symmetry and is octahedrally coordinated to six water molecules, hydrogen bonded to the Ph3AsO molecules and to the bromide anions forming a second coordination sphere in a nearly octahedral arrangement. In the orange complex the cation is pentacoordinated with the four oxygen atoms of the Ph3AsO ligands forming the basis of a tetragonal pyramid and with one Br- anion in the apical position. The absorption spectrum of the orange complex is compared with the spectra of other Ni(II) square pyramidal complexes described in the literature. © 1984.

N-methyl-D-aspartate channel and consciousness: From signal coincidence detection to quantum computing

Research on Blindsight, Neglect/Extinction and Phantom limb syndromes, as well as electrical measurements of mammalian brain activity, have suggested the dependence of vivid perception on both incoming sensory information at primary sensory cortex and reentrant information from associative cortex. Coherence between incoming and reentrant signals seems to be a necessary condition for (conscious) perception. General reticular activating system and local electrical synchronization are some of the tools used by the brain to establish coarse coherence at the sensory cortex, upon which biochemical processes are coordinated. Besides electrical synchrony and chemical modulation at the synapse, a central mechanism supporting such a coherence is the N-methyl-D-aspartate channel, working as a 'coincidence detector' for an incoming signal causing the depolarization necessary to remove Mg 2+, and reentrant information releasing the glutamate that finally prompts Ca 2+ entry. We propose that a signal transduction pathway activated by Ca 2+ entry into cortical neurons is in charge of triggering a quantum computational process that accelerates inter-neuronal communication, thus solving systemic conflict and supporting the unity of consciousness. © 2001 Elsevier Science Ltd.

Production of Ti-35Nb alloy by powder metallurgy for aerospace application

Titanium and its alloys provide high strength-to-weight ratios, good fatigue strength and increased corrosion resistance compared with others materials. Its acceptance in aerospace has been limited by costs considerations such as high cost of raw material, high buy-to-fly ratios and expensive machining operations. Significant cost reductions can be obtained by vacuum sintering and powder metallurgy (P/M) techniques by producing near net shapes and consequently minimizing material waste and machining time. The Ti 35Nb alloy exhibit a low modulus of elasticity. Stemming from the unique combination of high strength, low modulus of elasticity and low density, this alloy is intrinsically more resistant to shock and explosion damages than most other engineering materials. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by sintering between 900 and 1600 °C, in vacuum. Sintering behavior was studied by means of dilatometry. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. Density was measured by Archimedes method. Copyright © 2004 Society of Automotive Engineers, Inc.

Estudo morfológico do tecido hepático de Leporinus macrocephalus

The objective of this work was to analyze the liver of Leporinus macrocephalus at the macroscopic and histologic level by evaluating the characteristics of the hepatic tissue. The fishes from a fishery in Bauru, S.P., were collected and sacrificed by destroying the spinal cord; afterwards the collected hepatic tissue was fixed and followed by histological routine. Macroscopic analysis of L. macrocephalus liver showed an organ of homogeneous structure, with red-brown color, located in the medial region of the body, caudal to heart and after the gills. It showed 3 pyramidal lobes, one central and two lateral right and left. The histological analysis showed the hepatic tissue constituted by hepatocytes cords surrounded by sinusoids, named muralium duplex. It yet revealed the diffused, distribution bile system by hepatic parenchyma, showing ducts with simple cubic epithelium, surrounded by muscular fibres and connective tissue. Cells of the exocrine pancreatic tissue were observed surrounding blood vessels in acinar arrangement as zymogen granules. Furthermore, there are melanomacrophages centers distributed along the hepatic parenchyma, preferably next to the blood vessels, constituted by cells accumulating material, such as melanin and lipofucsin, whose presence may be related to the nutritional status of the fish.

Desempenho em consciência fonológica, memória operacional, leitura e escrita na dislexia familial

Background: familial dyslexia. Aim: to characterize and compare the phonological awareness, working memory, reading and writing abilities of individuals whose family members are also affected. Method: in this study 10 familial nuclei of natural family relationship of individuals with dyslexia were analyzed. Families of natural individuals living in the west region of the state of São Paulo were selected. Inclusion criteria were: to be a native speaker of the Brazilian Portuguese language, to have 8 years of age or more, to present positive familial history for learning disabilities, That is, to present at least one relative with difficulties in learning. Exclusion criteria were: to present any neurological disorder genetically caused or not, in any of the family members, such as dystonia, extra pyramidal diseases, mental disorder, epilepsy, attention deficit and hyperactivity disorder (ADHA); psychiatric symptoms or conditions; or any other pertinent conditions that could cause errors in the diagnosis. As for the diagnosis of developmental dyslexia, information about the familial history of the adolescents and children was gathered with the parents, so that a detailed pedigree could be delineated. Neurological, psychological, speech-language, and school performance evaluations were made with the individuals and their families. Results: the results of this study suggest that the dyslexic individuals and their respective relatives, also with dyslexia, presented lower performances than the control group in terms of rapid automatic naming, reading, writing and phonological awareness. Conclusion: deficits in phonological awareness, working memory, reading and writing seem to have genetic susceptibility that possibly determine, when in interaction with the environment, the manifestation of dyslexia.

Effect of time in hardness test on artificially demineralized human dental enamel

A cross-sectional microhardness (CSMH) test was carried out in human dental enamel exposed to a demineralizing solution in order to evaluate two different times of indentation in sound tissue and artificially induced caries. Twenty caries-free extracted human molars had one of their smooth surfaces sectioned and the enamel surface was isolated with nail polish except for an area of 6 mm2. These specimens were submitted to artificially induced enamel caries on a lactate buffer containing 0.1 ppm fluoride (F) during 28 days. All specimens were bisected to create groups A and B in which CSMH test was performed employing a Knoop indenter with a 25g load for 5 or 10 s, respectively. Student's paired t-test (p<0.05) was used to determine statistically significant differences between group A and B in 7 depths. There were no significant differences between any of the analyzed depths. Since the present experiment showed no significant difference when comparing indentations made with a 25 g load during either 5 or 10 s in different depths, this method can be used with either one of the time intervals tested without compromising a CSMH test on artificially demineralized human enamel.

Portable Hardness tester for timber classification

Hardness is a property largely used in material specifications, mechanical and metallurgical research and quality control of several materials. Specifically for timber, Janka hardness is a simple, quick and easy test, with good correlations with the compression parallel to grain strength, a strong reference in structural classification for this material. More recently, international studies have reported the use of Brinell hardness for timber assessment which resumes the advantages previously mentioned for Janka hardness and make it easier to be performed in the field, especially because of the lower magnitude of the involved loads. A first generation of an equipment for field evaluation of hardness in wood - Portable Hardness tester for wood - based on Brinell hardness has already been developed by the Research Group on Forest Products from FCA/UNESP, Brazil, with very good correlations between the evaluated hardness and several other mechanical properties of the material when performing tests with different species of native and reforested wood (traditionally used as ties - sleepers - in railways). This paper presents results obtained in the experimental program with the first generation of this equipment and preliminary tests with its second generation, which uses accelerometers to substitute the indentation measurements in wood. For the first generation of the equipment functional and calibration tests were carried out using 16 native and reforestation timber lots, among there E. citriodora, E. tereticornis, E. saligna, E. urophylla, E. grandis, Goupia glabra and Bagassa guianenses, with different origins and ages. The results obtained confirm its potential in the classification of specimens, with inclusion errors varying from 4.5% to 16.6%.

Morphological aspects of the liver of the Podocnemis expansa (Testudines, podocnemididae)

The liver of P. expansa was characterized morphohistologically. To this end, twenty livers from clinically healthy male and female Podocnemis expansa, weighing from 2.0 to 4,5 kg, supplied by the commercial breeder Fazenda Moenda da Serra, in Araguapaz, state of Goiás, Brazil, were analyzed macro-and microscopically. The coelomatic cavity was opened and the topography of the fresh organs was examined visually. After the histological preparation, the slides were stained with Hematoxylin and Eosin (HE), Periodic Acid-Schiff (PAS), Gomori Trichrome, Reticulin and Picrosirius. The liver of P. expansa is a voluminous organ with an approximately rectangular shape and brown coloration, varying from light to dark shades, and is divided into a right lobe, left lobe, and a central portion. The right lobe is the largest of the three portions. The gall bladder is located in a depression in the caudal portion of the right lobe, where the gall duct begins and empties into the duodenum. Histologically, the hepatocytes are arranged in the form of double cords surrounded by winding sinusoidal capillaries. In cross section, they resemble acini containing approximately two to five hepatocytes surrounding a probable central biliary canaliculus. The hepatocytes are polyhedral or pyramidal in shape, of uniform size, with a few central nuclei and others displaced peripherally, and the cytoplasm is little eosinophilic when analyzed by the HE staining technique. The parenchyma is supported by delicate reticular fibers surrounding hepatocytes and sinusoids. The parenchyma and perisinusoidal spaces contain large quantities of melanomacrophages, mainly close to the portal spaces.

Physicochemical analysis of Ti-Si-B powder aalloys

Titanium alloys of Ti-Si-B system were manufactured by blended elemental powder method using Ti, Si and B powders as starting materials. It was found that uniaxial and isostatic pressing followed by hot pressing at around 1000°C, for 20 minutes, provided good densification of such alloys. The physicochemical studies were performed by means of scanning electron microscopy, X-ray diffraction, atomic force microscopy and microindentation/wear tests. The investigations revealed a multiphase microstructure formed mainly by α-titanium, Ti6Si2B, Ti5Si3, TiB and Ti3Si phases. The phase transformations after pressureless sintering at 1200°C was also studied by X-ray diffraction for the Ti-18Si-6B composition. As stated in some other researches, these intermetallics in the α-titanium matrix provide high wear resistance and hardness, with the best wear rate of 0.2 mm3/N.m and the highest hardness of around 1300 HV. © (2012) Trans Tech Publications, Switzerland.

C-terminal processing of the teneurin proteins: Independent actions of a teneurin C-terminal associated peptide in hippocampal cells

Many neuropsychiatric conditions have a common set of neurological substrates associated with the integration of sensorimotor processing. The teneurins are a recently described family of proteins that play a significant role in visual and auditory development. Encoded on the terminal exon of the teneurin genes is a family of bioactive peptides, termed teneurin C-terminal associated peptides (TCAP), which regulate mood-disorder associated behaviors. Thus, the teneurin-TCAP system could represent a novel neurological system underlying the origins of a number of complex neuropsychiatric conditions. However, it is not known if TCAP-1 exerts its effects as part of a direct teneurin function, whereby TCAP represents a functional region of the larger teneurin protein, or if it has an independent role, either as a splice variant or post-translational proteolytic cleavage product of teneurin. In this study, we show that TCAP-1 can be transcribed as a smaller mRNA transcript. After translation, further processing yields a smaller 15. kDa protein containing the TCAP-1 region. In the mouse hippocampus, immunoreactive (ir) TCAP-1 is exclusively localized to the pyramidal layers of the CA1, CA2 and CA3 regions. Although the localization of TCAP and teneurin in hippocampal regions is similar, they are distinct within the cell as most ir-teneurin is found at the plasma membrane, whereas ir-TCAP-1 is predominantly found in the cytosol. Moreover, in mouse embryonic hippocampal cell culture, FITC-labeled TCAP-1 binds to the plasma membrane and is taken up into the cytosol via dynamin-dependent caveolae-mediated endocytosis. Our data provides novel evidence that TCAP-1 is structurally and functionally distinct from the larger teneurins. © 2012.

Gestational protein restriction induces CA3 dendritic atrophy in dorsal hippocampal neurons but does not alter learning and memory performance in adult offspring

Studies have demonstrated that nutrient deficiency during pregnancy or in early postnatal life results in structural abnormalities in the offspring hippocampus and in cognitive impairment. In an attempt to analyze whether gestational protein restriction might induce learning and memory impairments associated with structural changes in the hippocampus, we carried out a detailed morphometric analysis of the hippocampus of male adult rats together with the behavioral characterization of these animals in the Morris water maze (MWM). Our results demonstrate that gestational protein restriction leads to a decrease in total basal dendritic length and in the number of intersections of CA3 pyramidal neurons whereas the cytoarchitecture of CA1 and dentate gyrus remained unchanged. Despite presenting significant structural rearrangements, we did not observe impairments in the MWM test. Considering the clear dissociation between the behavioral profile and the hippocampus neuronal changes, the functional significance of dendritic remodeling in fetal processing remains undisclosed. © 2012 ISDN.

Local electronic structure, optical bandgap and photoluminescence (PL) properties of Ba(Zr0.75Ti0.25)O3 powders

Ba(Zr0.75Ti0.25)O3 (BZT-75/25) powders were synthesized by the polymeric precursor method. Samples were structurally characterized by X-ray diffraction (XRD), Rietveld refinement, X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) techniques. Their electronic structures were evaluated by first-principle quantum mechanical calculations based on density functional theory at the B3LYP level. Their optical properties were investigated by ultraviolet-visible (UV-Vis) spectroscopy and photoluminescence (PL) measurements at room temperature. XRD patterns and Rietveld refinement data indicate that the samples have a cubic structure. XANES spectra confirm the presence of pyramidal [TiO5] clusters and octahedral [TiO6] clusters in the disordered BZT-75/25 powders. EXAFS spectra indicate distortion of Ti-O and Ti-O-Ti bonds the first and second coordination shells, respectively. UV-Vis absorption spectra confirm the presence of different optical bandgap values and the band structure indicates an indirect bandgap for this material. The density of states demonstrates that intermediate energy levels occur between the valence band (VB) and the conduction band (CB). These electronic levels are due to the predominance of 4d orbitals of Zr atoms in relation to 3d orbitals of Ti atoms in the CB, while the VB is dominated by 2p orbitals related to O atoms. There was good correlation between the experimental and theoretical optical bandgap values. When excited at 482 nm at room temperature, BZT-75/25 powder treated at 500 C for 2 h exhibited broad and intense PL emission with a maximum at 578 nm in the yellow region. © 2013 Elsevier Ltd. All rights reserved.

Anatomical study of the retroarticular process in dry human skulls

Introduction: The retroarticular process is a bony prominence formed by the thickening of the lateral border of the mandibular fossa, forming the posterior wall of the temporomandibular joint. Since little is known and discussed about the retroarticular process, our aim was to study its presence, shape and size, relating these findings to the shape of the skulls according to the horizontal cephalic index. Materials and Methods: We used 400 dry human skulls of the Institute of Science and Technology - UNESP Anatomy Laboratory. Each skull was classified in brachycranics, mesocranics or dolichocranics, and then positioned on a craneostat to measure the height of the retroarticular process from its lower extremity to the auriculo-orbital plane. The width was obtained by measuring the base of the process on its longer lateral axis. Results: The retroarticular process was found bilaterally in 397 skulls (99.25%). All the processes were classified into the following shapes: pyramidal (35.55%), tubercular (31.78%), mammilar (20.73%), crest-like (9.05%) and molar shape (2.89%); 254 skulls (63.50%) showed the same type of process at the right and left sides (Kappa=0.496, moderate agreement). The average height and width were 5.28 mm and 12.81 mm, respectively. Conclusion: The retroarticular process was found in almost all the skulls examined. There are no significant evidences about the relationship among the presence, shape and size of the retroarticular process and the shape of the skulls according to the horizontal cephalic index. However, our findings led us to infer that there would be a functional relationship between the process and the temporomandibular joint.

Optical, mechanical and surface properties of amorphous carbonaceous thin films obtained by plasma enhanced chemical vapor deposition and plasma immersion ion implantation and deposition

Diverse amorphous hydrogenated carbon-based films (a-C:H, a-C:H:F, a-C:H:N, a-C:H:Cl and a-C:H:Si:O) were obtained by radiofrequency plasma enhanced chemical vapor deposition (PECVD) and plasma immersion ion implantation and deposition (PIIID). The same precursors were used in the production of each pair of each type of film, such as a-C:H, using both PECVD and PIIID. Optical properties, namely the refractive index, n, absorption coefficient, α, and optical gap, ETauc, of these films were obtained via transmission spectra in the ultraviolet-visible near-infrared range (wavelengths from 300 to 3300 nm). Film hardness, elastic modulus and stiffness were obtained as a function of depth using nano-indentation. Surface energy values were calculated from liquid drop contact angle data. Film roughness and morphology were assessed using atomic force microscopy (AFM). The PIIID films were usually thinner and possessed higher refractive indices than the PECVD films. Determined refractive indices are consistent with literature values for similar types of films. Values of ETauc were increased in the PIIID films compared to the PECVD films. An exception was the a-C:H:Si:O films, for which that obtained by PIIID was thicker and exhibited a decreased ETauc. The mechanical properties - hardness, elastic modulus and stiffness - of films produced by PECVD and PIIID generally present small differences. An interesting effect is the increase in the hardness of a-C:H:Cl films from 1.0 to 3.0 GPa when ion implantation is employed. Surface energy correlates well with surface roughness. The implanted films are usually smoother than those obtained by PECVD. ©2013 Elsevier B.V. All rights reserved.