Induced polarization, resistivity, and self-potential: a case history of contamination evaluation due to landfill leakage

This article compares the efficiency of induced polarization (IP) and resistivity in characterizing a contamination plume due to landfill leakage in a typical tropical environment. The resistivity survey revealed denser electrical current flow that induced lower resistivity values due to the high ionic content. The increased ionic concentration diminished the distance of the ionic charges close to the membrane, causing a decrease in the IP phenomena. In addition, the self-potential (SP) method was used to characterize the preferential flow direction of the area. The SP method proved to be effective at determining the flow direction; it is also fast and economical. In this study, the resistivity results were better correlated with the presence of contamination (lower resistivity) than the IP (lower chargeability) data.

Implications of groundwater weathered profile interactions to the mobilization of radionuclides

This study reports the nature and extent of open-system interaction between groundwater and a weathered profile developed in the high grade thorium and REE ore body in Morro do Ferro, Pocos de Caldas plateau. The radioelement mobility in the shallow oxidizing environment was considered by using chemical data in conjunction with U-234/U-238, Ra-226/Th-230, Th-230/U-234, Th-228/Th-232, Ra-228/Th-232 and Th-230/Ra-228 activity ratios (AR's) for borehole spoil and groundwater samples.Recharging groundwater from the studied borehole has low salinity values, with total dissolved solids content of 14.7 mg/l and total ionic strength of 0.00018. The ratio of the weight of dissolved radioelement per unit volume of solution to the weight of radioelement in solid phase per unit weight of solid phase showed that the radioelement solubility in the studied waters varied according to the following order: radium> uranium >thorium.U-234/U-238 AR's less than 1 were measured in solid phase and can justify the enhancement of U-234 in solution. Ra-226/Th-230 AR's greater than 1 and Th-230/U-234 AR'S less than 1 were evaluated between 20 and 27 m in depth, where a 2.1-m thick magnetite dike was intersected. These ratios could be justified by deposition of U and Ra associated with Fe-Mn oxides and kaolinite, where mineral saturation indices evaluated from the available data confirm this possibility. Covariations among disequilibria involving Th-228/(228) Ra and Ra-228/Th-232 AR's showed the preferential removal of Ra-228 relative to Tn isotopes, Th-228 and Th-232. The recent deposition of radium within the timescale of at least the last 35 years also is suggested. (C) 1998 Elsevier B.V. Ltd. All rights reserved.

Radon in groundwater contaminated by dissolved hydrocarbons in Santa Barbara d'Oeste, São Paulo State, Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Nanocompósitos cerâmicos a partir do processo de moagem mecânica de alta energia

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Reaction pathway to the synthesis of anatase via the chemical modification of titanium isopropoxide with acetic acid

Anatase nanoparticles were obtained through a modified sol-gel route from titanium isopropoxide modified with acetic acid in order to control hydrolysis and condensation reactions. The modification of Ti(O(i)Pr)(4) with acetic acid reduces the availability of groups that hydrolyze and condense easily through the formation of a stable complex whose structure was determined to be Ti(OCOCH(3))(O(i)Pr)(2) by means of FTIR and (13)C NMR. The presence of this complex was confirmed with FTIR in the early stages of the process. A doublet in 1542 and 1440 cm(-1) stands for the asymmetric and symmetric stretching vibrations of the carboxylic group coordinated to Ti as a bidentate ligand. The gap of 102 cm(-1) between these signals suggests that acetate acts preferentially as a bidentate rather than as a bridging ligand between two titanium atoms. The use of acetic acid as modifier allows the control of both the degree of condensation and oligomerization of the precursor and leads to the preferential crystallization of TiO(2) in the anatase phase. A possible reaction pathway toward the formation of anatase is proposed on the basis of the intermediate species present in a 1:1 Ti(O(i)Pr)(4):CH(3)COOH molar system in which esterification reactions that introduce H(2)O into the reaction mixture were seen to be negligible. The Rietveld refinement and TEM analysis revealed that the powder is composed of isotropic anatase nanocrystallites.

Fatores que afetam a oviposição de Bemisia tabaci (Genn.) biótipo B (Hemiptera: Aleyrodidae) em pimentão

Para avaliar o comportamento de oviposição da mosca-branca, Bemisia tabaci (Genn.) biótipo B, em relação à posição da folha na planta, à área do limbo foliar, à idade da planta e à densidade de adultos na cultura do pimentão, foram realizados três testes, utilizando-se a cultivar de pimentão Magali-R. Os testes foram realizados em casa-de-vegetação e no Laboratório de Entomologia da DEFERS/UNESP, Campus de Ilha Solteira-SP. Nos testes com chance de escolha, plantas com 25, 30, 35, 40 e 45 dias de idade foram utilizadas para avaliar os efeitos da idade sobre a oviposição da mosca-branca, enquanto que em plantas com 35 dias estudou-se a distribuição de ovos da mosca-branca na planta e no limbo foliar. em plantas de 35 dias de idade, avaliou-se o efeito de diferentes densidades populacionais do inseto (50, 100, 150, 200 e 250 adultos/ planta) sobre o número de ovos depositados. No teste sem chance de escolha, utilizaram-se plantas com 35 dias de idade para avaliar o efeito das densidades sobre a oviposição da mosca-branca. B. tabaci biótipo B preferiu ovipositar da terceira a sexta folha a partir do ápice da planta localizadas nos terços médio e superior de planta de pimentão e nas áreas do limbo foliar localizadas nos lóbulos direito e esquerdo, próximas à base da folha. Plantas com 40 e 45 dias, são preferidas para oviposição e, em densidades de 200 e 250 adultos por planta, as moscas-brancas depositam ovos em número suficiente para diferenciar genótipos de pimentão com diferentes graus resistência a esta praga.

Crescimento de genótipos de sorgo plantados nos sentidos Norte-Sul e Leste-Oeste

O objetivo do presente trabalho foi estudar o crescimento de plantas de seis genótipos de sorgo (Sorghum bicolor (L.) Moench), a saber: dois sacarinos, dois graníferos e dois forrageiros, cultivadas com as linhas de plantio orientadas no sentido Norte-Sul e Leste-Oeste. Instalou-se, em setembro de 1994, o ensaio em área experimental da Faculdade de Ciências Agrárias e Veterinárias (FCAVJ) - UNESP, utilizando delineamento em blocos casualizados, com doze tratamentos e três repetições. As avaliações foram feitas mediante amostragens semanais, determinando-se massa seca acumulada, área foliar e distribuição da massa seca nas diferentes partes da planta. Os materiais sacarinos cresceram mais que os graníferos, e os graníferos tiveram ciclo mais curto que os demais. A distribuição de massa seca caracterizou aptidão de cada genótipo, ou seja, alta eficiência na exportação de material para os colmos nos sacarinos, exportação preferencialmente para os grãos nos graníferos, e exportação para colmos e grãos, evidenciando dupla aptidão, nos forrageiros. O padrão de distribuição de massa seca não foi afetado pela orientação das linhas de plantio.

A criança disfônica: diagnóstico, tratamento e evolução clínica

Os nódulos vocais são causas freqüentes de disfonias infantis, porém, através das vídeoendoscopias, outras lesões têm sido diagnosticadas na laringe infantil, como os cistos, sulcos, pontes e micromembranas, denominadas de lesões estruturais mínimas. OBJETIVO: Avaliar, em 71 crianças com disfonia agendadas nos ambulatórios de Foniatria da Faculdade de Medicina de Botucatu (Unesp) nos últimos cinco anos: sexo, idade, diagnósticos, tratamentos e evolução clínica. FORMA DE ESTUDO: Clínico retrospectivo. CASUÍSTICA E MÉTODO: Realizou-se estudo retrospectivo das avaliações otorrinolaringológicas e endoscópicas de 71 crianças com queixas de disfonia e idade entre 3 a 13 anos (45 meninos e 26 meninas). As crianças haviam sido submetidas a exame endoscópico com telescópio rígido ou nasofibroscópio flexível. Foram excluídas as crianças com disfonias funcionais ou com queixas de obstrução respiratória. RESULTADOS: Os principais diagnósticos foram: nódulo vocal (47 casos; 66,2%), cisto epidérmico (7 casos; 9,9%), cisto aberto fistulizado (6 casos; 8,4%), sulco vocal (5 casos; 7,1%), ponte + cisto (2 casos; 2,8%), micromembrana anterior (2 casos; 2,8%) e pólipo vocal (2 casos; 2,8%). As disfonias foram mais freqüentes entre os meninos (63,3%). A fonoterapia isolada foi o tratamento de escolha nos casos de nódulo vocal (evolução favorável), sulco vocal (evolução desfavorável) e micro-membrana (evolução desfavorável). Nas demais lesões (cistos, pontes e pólipos) o tratamento de escolha foi a cirurgia associada à fonoterapia, com resultados satisfatórios, exceto nos casos que recusaram a cirurgia. CONCLUSÃO: Os nódulos vocais são as principais causas de disfonias em crianças, porém as lesões estruturais mínimas mostraram-se também freqüentes, exigindo exame minucioso para o diagnóstico.

Preparation and characterization of nanocrystalline h-BN films prepared by PECVD method

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Podzolization as a deferralitization process: a study of an Acrisol-Podzol sequence derived from Palaeozoic sandstones in the northern upper Amazon Basin

Morphological, geochemical and mineralogical studies were carried out in a representative soil catena of the low-elevation plateaux of the upper Amazon Basin to interpret the steps and mechanisms involved in the podzolization of low-activity clay soils. The soils are derived from Palaeozoic sandstones. They consist of Hydromorphic Podzols under tree savannah in the depressions of the plateaux and predominantly of Acrisols covered by evergreen forest elsewhere.Incipient podzolization in the uppermost Acrisols is related to the formation of organic-rich A and Bhs horizons slightly depleted in fine-size particles by both mechanical particle transfer and weathering. Weathering of secondary minerals by organic acids and formation of organo-metallic complexes act simultaneously over short distances. Their vertical transfer is limited. Selective dissolution of aluminous goethite, then gibbsite and finally kaolinite favour the preferential cheluviation of first Fe and secondly Al. The relatively small amount of organo-metallic complexes produced is related to the quartzitic parent materials, and the predominance of Al over Fe in the spodic horizons is due to the importance of gibbsite in these low-activity clay soils.Morphologically well-expressed podzols occur in strongly iron-depleted topsoils of the depression. Mechanical transfer and weathering of gibbsite and kaolinite by organic acids is enhanced and leads to residual accumulation of sands. Organo-metallic complexes are translocated in strongly permeable sandy horizons and impregnate at depth the macro-voids of embedded soil and saprolite materials to form the spodic Bs and 2BCs horizons. Mechanical transfer of black particulate organic compounds devoid of metals has occurred later within the sandy horizons of the podzols. Their vertical transfer has formed well-differentiated A and Bh horizons. Their lateral removal by groundwater favours the development of an albic E horizon. In an open and waterlogged environment, the general trend is therefore towards the removal of all the metals that have initially accumulated as a response to the ferralitization process and have temporarily been sequestrated in organic complexes in previous stages of soil podzolization.

Colonization of a 'Lost World': Encrustation patterns in modern subtropical brachiopod assemblages.

The encrustation of Paleozoic rhynchonelliform brachiopods has been studied for decades, but modern brachiopods have not received similar scrutiny. The discovery of abundant subtropical brachiopods from the Southeast Brazilian Bight provides an unprecedented opportunity to assess epibiont abundance, diversity, and encrustation patterns in modern brachiopod assemblages. Across the outer shelf, encrustation frequencies vary among taxa, from mean values of 0.45% for Platidia to 9.3% for Argyrotheca. Encrustation frequencies for Bouchardia increase from 1.6% on the outer shelf to 84% on the inner shelf Larger valves are encrusted more frequently, and epibionts preferentially colonize valve interiors. Increased encrustation on the inner shelf may reflect the greater surface area of larger hosts, longer exposure of dead shells, water-mass characteristics, sedimentation rates, productivity, or other factors that vary with depth. Inner-shelf brachiopods exhibit encrustation frequencies comparable to those reported for epifaunal bivalves. The epibiont fauna is dominated by bryozoans and serpulids, with minor roles played by spirorbids, bivalves, barnacles, foraminifera, algae, and other taxa. Epibiont abundance at each site is highly variable, but sites are similar in rank importance of epibiont taxa. A different suite of epibionts colonized Paleozoic brachiopods, but similar patterns of encrustation have been observed, including preferential settlement according to valve morphology. These results provide a baseline for evaluating the encrustation of modern bivalves and ancient brachiopods, and may elucidate the macroevolutionary history of epibionts and their relationship to their hosts.

SrBi2Nb2O9 thin films crystallized using a low power microwave oven

SrBi2Nb2O9 thin films were produced by the polymeric precursor method using an aqueous solution. The crystallization of the films was carried out using a domestic microwave oven by means of a SiC susceptor in order to absorb the microwave energy and rapidly transfer the heat to the film. Low microwave power and short time have been used. The films obtained are well-adhered, homogeneous and with good specularity, even when treated at 600 degreesC for 10 min. The microstructure and the structure of the films can be tuned by adjusting the crystallization conditions. Depending on the direction of the heat flux it is possible to obtain preferential oriented or polycrystalline films in the microwave oven for 10 min. The microstructure presented a polycrystalline nature with spheroid small mean grain size when the susceptor is placed above the substrate. When the susceptor is placed below the substrate, the films presented platelet grains with mean grain size around 250 nm and a 001 orientation. For comparison, films were also prepared by the conventional method at 700 degreesC for 2 h. (C) 2003 Elsevier Ltd. All rights reserved.

EFFECT OF THE ADDITION OF CR AND NB ON THE MICROSTRUCTURE AND ELECTROCHEMICAL CORROSION OF HEAT-TREATABLE AL-ZN-MG ALLOYS

The effect of the addition of Cr and Nb on the microstructure and the electrochemical corrosion of the weldable, high-strength and stress corrosion cracking (SCC) resistant Al-5%Zn-1.67%Mg-0.23%Cu alloy (H) has been studied. Combined additions of the alloying elements, J (with Nb), L (with Cr) and O (with Cr and Nb) and different heat treatments, ST (cold-rolled), A (annealed), F (quenched), B (quenched and aged) and C (quenched in two steps and aged), to obtain different microstructures and hardness have been performed. To correlate the electrochemical corrosion with the microstructure of the specimens, corrosion potential (E(cor)) measurements in different chloride solutions were performed and optical microscopy, SEM, TEM and EDX were applied. In chloride solutions containing dissolved O-2 or H2O2, the present alloys were polarized up to the pitting attack. It was shown that the E(cor) measurements were very sensitive to the alloy composition and heat treatment, increasing in the order H < J < L < O < Al (for a given heat treatment) and F < A approximate to ST < B < C (for a given alloy). The MgZn2 precipitates of the annealed (A) and cold-rolled (ST) specimens were dissolved in chloride solutions containing oxidizing agents and pitting attack was shown to develop in the cavities where the precipitates were present. In the specimens B and C, the compositions of the precipitate free zones was found to be equal to that of the matrix solid solution and preferential intergranular attack was not evident, this being in agreement with their SCC resistance. The addition of Cr and Nb increased the pitting corrosion resistance. The effects of Cr and Nb were additive, that of Cr being predominant, either, in the E(cor) shift or in the increase in the pitting corrosion resistance.

Effect of In concentration in the starting solution on the structural and electrical properties of ZnO films prepared by the pyrosol process at 450 degrees C

Undoped and indium-doped Zinc oxide (ZnO) solid films were deposited by the pyrosol process at 450 degrees C on glass substrates From solutions where In/Zn ratio was 2, 5, and 10 at.%. Electrical measurements performed at room temperature show that the addition of indium changes the resistance of the films. The resistivities of doped films are less than non-doped ZnO films by one to two orders of magnitude depending on the dopant concentration in the solution. Preferential orientation of the films with the c-axis perpendicular to the substrate was detected by X-ray diffraction and polarized extended X-ray absorption fine structures measurements at the Zn K edge. This orientation depends on the indium concentration in the starting solution. The most textured films were obtained for solutions where In/Zn ratio was 2 and 5 at.%. When In/Zn = 10 at.%, the films had a nearly random orientation of crystallites. Evidence of the incorporation of indium in the ZnO lattice was obtained from extended X-ray absorption fine structures at the In and Zn K edges. The structural analysis of the least resistive film (Zn/In = 5 at.%) shows that In substitutes Zn in the wurtzite structure. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Theoretical study of MgO(001) surfaces: Pure, doped with Fe, Ca, and Al, and with and without adsorbed water

Ab initio calculations of large cluster models have been performed in order to study water adsorption at the five-fold coordinated adsorption site on pure Mg(001) and MgO(001) surfaces doped with Fe, Ca, and Al. The geometric parameters of the adsorbed water molecule have been optimized preparatory to analysis of binding energies, charge transfer, preferential sites of interaction, and bonding distances. We have used Mulliken population analysis methods in order to analyze charge distributions and the direction of charge transfer. We have also investigated energy gaps, HOMO energies, and SCF orbital energies as well as the acid-base properties of our cluster model. Numerical results are compared, where possible, with experiment and interpreted in the framework of various analytical models. (C) 2001 John Wiley & Sons, Inc.