Cotton response to mepiquat chloride and temperature

Gibberellin inhibitor growth regulators are used for cotton (Gossypium hirsutum L.) canopy manipulation to avoid excess growth and yield losses. However, under temperatures below or over the optimum for cotton production the effect of mepiquat chloride (MC) has not always been significant. In this experiment, cotton plants were grown in growth chambers to study the response to MC as affected by temperature and to determine if an increase in dose could overcome the temperature effects. Mepiquat chloride was applied at rates of 0, 15 and 30 g ai ha-1 at the pinhead square stage. Plants were then grown under three temperature regimes: 25/15 °C, 32/22 °C, and 39/29 °C (day/night temperatures) for 51 days. Higher temperatures increased plant height, reproductive branches, fruit number, fruit abscission, and photosynthesis per unit area, but decreased leaf area and chlorophyll. The largest effect of MC on plant height was observed when the daily temperature was 32 °C, with nights of 22 °C, which was also best for plant growth. High temperatures not only decreased the effectiveness of MC on plant height control, but also caused lower dry matter and fruit number per plant. Low temperatures (25/15 ºC) decreased cotton growth and fruit retention, but a higher concentration of MC was required per unit of growth reduction as compared with 32/22 ºC. At high temperatures, the rate of MC to be applied must be disproportionately increased, because either plant growth is impaired by high temperature lessening the effect of MC, or degradation of MC within the plant is too rapid.

Alterações de alguns atributos físicos e das frações húmicas de um Nitossolo vermelho na sucessão milheto-soja em sistema plantio direto

No Estado de São Paulo, restrições do regime de chuvas no período de outono-inverno e temperaturas elevadas limitam a produção e a manutenção de cobertura no solo, tornando importante estudar alternativas para a implantação eficaz do Sistema Plantio Direto nesse Estado, especialmente para produção de fitomassa e manejo adequado para maior persistência da palha, em quantidade suficiente para melhoria da qualidade física e da matéria orgânica do solo. O experimento, conduzido em Nitossolo Vermelho distroférrico, na Fazenda Experimental Lageado-FCA-UNESP-Botucatu, teve por objetivo estudar no sistema plantio direto as prováveis alterações de alguns atributos físicos e das frações húmicas do solo com a utilização do milheto, verificando sua resposta, em três épocas de semeadura e sob cinco manejos dos resíduos, após cinco anos de estabelecida essa sucessão. O delineamento experimental foi o de blocos casualizados, com esquema de parcelas subdivididas, com quatro repetições. As parcelas foram representadas por três épocas de semeadura da cultura do milheto: época 1 (E1), época 2 (E2) e época 3 (E3). As subparcelas foram representadas por manejos da ceifa da fitomassa, sendo: manejo 1 (M1) - ceifa a cada florescimento e retirada da fitomassa; manejo 2 (M2) - ceifa a cada florescimento e permanência da fitomassa; manejo 3 (M3) - ceifa apenas no primeiro florescimento e retirada da fitomassa; manejo 4 (M4) - ceifa apenas no primeiro florescimento e permanência da fitomassa; e manejo 5 (M5) - livre crescimento. Foram coletadas amostras de solo com estrutura indeformada para realização das análises físicas, para as quais as profundidades amostradas foram: 0-0,05, 0,05-0,10 e 0,10-0,20 m. Para fracionamento químico da matéria orgânica, as profundidades foram de 0-0,05 e 0,05-0,10 m. em relação às culturas, avaliou-se a produtividade da soja, e para o milheto, a quantidade de matéria seca produzida pela parte aérea e a percentagem de fitomassa em cobertura deixada sobre o solo. A produtividade de matéria seca do milheto decresceu na ordem E1 > E2 > E3. A densidade do solo, a macroporosidade, a microporosidade e a porosidade total variaram com a época de semeadura do milheto. A adição contínua de fitomassa com ceifa a cada florescimento e permanência da cobertura proporcionou maior incremento nas frações menos estáveis da matéria orgânica (ácido húmico e ácido fúlvico). Recomenda-se, diante das condições edafoclimáticas estudadas, a semeadura do milheto na segunda e terceira épocas com ceifa apenas no primeiro florescimento, sempre se utilizando da permanência da fitomassa, para obter melhor cobertura, qualidade física do solo (menor densidade do solo, maior porosidade total) e maior produtividade para soja.

Thermal analysis of biodegradable microparticles containing ciprofloxacin hydrochloride obtained by spray drying technique

Thermal analysis has been extensively used to obtain information about drug-polymer interactions and to perform pre-formulation studies of pharmaceutical dosage forms. In this work, biodegradable microparticles of poly(D,L-lactide-co-glycolide) (PLGA) containing ciprofloxacin hydrochloride (CP) in various drug:polymer ratios were obtained by spray drying. The main purpose of this study was to investigate the effect of the spray drying process on the drug-polymer interactions and on the stability of microparticles using differential scanning calorimetry (DSC), thermogravimetry (TG) and derivative thermogravimetry (DTG) and infrared spectroscopy (IR). The results showed that the high levels of encapsulation efficiency were dependant on drug:polymer ratio. DSC and TG/DTG analyses showed that for physical mixtures of the microparticles components the thermal profiles were different from those signals obtained with the pure substances. Thermal analysis data disclosed that physical interaction between CP and PLGA in high temperatures had occurred. The DSC and TG profiles for drug-loaded microparticles were very similar to the physical mixtures of components and it was possible to characterize the thermal properties of microparticles according to drug content. These data indicated that the spray dryer technique does not affect the physicochemical properties of the microparticles. In addition, the results are in agreement with IR data analysis demonstrating that no significant chemical interaction occurs between CP and PLGA in both physical mixtures and microparticles. In conclusion, we have found that the spray drying procedure used in this work can be a secure methodology to produce CP-loaded microparticles. (C) 2007 Elsevier B.V. All rights reserved.

Cerâmicas avançadas no processo de retificação cilíndrica externa de mergulho com rebolos diamantados com a técnica da mímima quantidade de lubrificação e refrigeração otimizada

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Physical-chemical and thermodynamic analyses of ethanol steam reforming for hydrogen production

Steam reforming is the most usual method of hydrogen production due to its high production efficiency and technological maturity the use of ethanol for this purpose is an interesting option because it is a renewable and environmentally friendly fuel. The objective of this article is to present the physical-chemical, thermodynamic, and exergetic analysis of a steam reformer of ethanol, in order to produce 0.7 Nm(3)/h of hydrogen as feedstock of a 1 kW PEMFC the global reaction of ethanol is considered. Superheated ethanol reacts with steam at high temperatures producing hydrogen and carbon dioxide, depending strongly on the thermodynamic conditions of reforming, as well as on the technical features of the reformer system and catalysts. The thermodynamic analysis shows the feasibility of this reaction in temperatures about 206 degrees C. Below this temperature, the reaction trends to the reactants. The advance degree increases with temperature and decreases with pressure. Optimal temperatures range between 600 and 700 degrees C. However, when the temperature attains 700 degrees C, the reaction stability occurs, that is, the hydrogen production attains the limit. For temperatures above 700 degrees C, the heat use is very high, involving high costs of production due to the higher volume of fuel or electricity used. The optimal pressure is 1 atm., e.g., at atmospheric pressure. The exergetic analysis shows that the lower irreversibility is attained for lower pressures. However the temperature changes do not affect significantly the irreversibilities. This analysis shows that the best thermodynamic conditions for steam reforming of ethanol are the same conditions suggested in the physical-chemical analysis.

Thermodynamic analysis of direct steam reforming of ethanol in molten carbonate fuel cell

Fuel cell as molten carbonate fuel cell (MCFC) operates at high temperatures. Thus, cogeneration processes may be performed, generating heat for its own process or for other purposes of steam generation in the industry. The use of ethanol is one of the best options because this is a renewable and less environmentally offensive fuel, and is cheaper than oil-derived hydrocarbons, as in the case of Brazil. In that country, because of technical, environmental, and economic advantages, the use of ethanol by steam reforming process has been the most investigated process. The objective of this study is to show a thermodynamic analysis of steam reforming of ethanol, to determine the best thermodynamic conditions where the highest volumes of products are produced, making possible a higher production of energy, that is, a more efficient use of resources. To attain this objective, mass and energy balances were performed. Equilibrium constants and advance degrees were calculated to get the best thermodynamic conditions to attain higher reforming efficiency and, hence, higher electric efficiency, using the Nernst equation. The advance degree (according to Castellan 1986, Fundamentos da Fisica/Quimica, Editora LTC, Rio de Janeiro, p. 529, in Portuguese) is a coefficient that indicates the evolution of a reaction, achieving a maximum value when all the reactants' content is used of reforming increases when the operation temperature also increases and when the operation pressure decreases. However, at atmospheric pressure (1 atm), the advance degree tends to stabilize in temperatures above 700 degrees C; that is, the volume of supplemental production of reforming products is very small with respect to high use of energy resources necessary. The use of unused ethanol is also suggested for heating of reactants before reforming. The results show the behavior of MCFC. The current density, at the same tension, is higher at 700 degrees C than other studied temperatures such as 600 and 650 degrees C. This fact occurs due to smaller use of hydrogen at lower temperatures that varies between 46.8% and 58.9% in temperatures between 600 and 700 degrees C. The higher calculated current density is 280 mA/cm(2). The power density increases when the volume of ethanol to be used also increases due to higher production of hydrogen. The highest produced powers at 190 mA/cm(2) are 99.8, 109.8, and 113.7 mW/cm(2) for 873, 923, and 973 K, respectively. The thermodynamic efficiency has the objective to show the connection among operational conditions and energetic factors, which are some parameters that describe a process of internal steam reforming of ethanol.

Processing and hygrothermal effects on viscoelastic behavior of glass fiber/epoxy composites

Fiber reinforced epoxy composites are used in a wide variety of applications in the aerospace field. These materials have high specific moduli, high specific strength and their properties can be tailored to application requirements. In order to screening optimum materials behavior, the effects of external environments on the mechanical properties during usage must be clearly understood. The environmental action, such as high moisture concentration, high temperatures, corrosive fluids or ultraviolet radiation (UV), can affect the performance of advanced composites during service. These factors can limit the applications of composites by deteriorating the mechanical properties over a period of time. Properties determination is attributed to the chemical and/or physical damages caused in the polymer matrix, loss of adhesion of fiber/resin interface, and/or reduction of fiber strength and stiffness. The dynamic elastic properties are important characteristics of glass fiber reinforced composites (GRFC). They control the damping behavior of composite structures and are also an ideal tool for monitoring the development of GFRC's mechanical properties during their processing or service. One of the most used tests is the vibration damping. In this work, the measurement consisted of recording the vibration decay of a rectangular plate excited by a controlled mechanism to identify the elastic and damping properties of the material under test. The frequency amplitude were measured by accelerometers and calculated by using a digital method. The present studies have been performed to explore relations between the dynamic mechanical properties, damping test and the influence of high moisture concentration of glass fiber reinforced composites (plain weave). The results show that the E' decreased with the increase in the exposed time for glass fiber/epoxy composites specimens exposed at 80 degrees C and 90% RH. The E' values found were: 26.7, 26.7, 25.4, 24.7 and 24.7 GPa for 0, 15, 30, 45 and 60 days of exposure, respectively. (c) 2005 Springer Science + Business Media, Inc.

Elastic properties of hygrothermally conditioned glare laminate

The influences of hygrothermal conditioning on mechanical properties of a fiber/metal laminate (FML) have been investigated by tensile and compression tests. The environmental action, such as high moisture concentration, high temperatures, corrosive fluids or ultraviolet radiation (UV), can affect the performance of advanced composites during service. In the present work, the results show that for the glass fiber/epoxy composites tensile and compression values decrease after hygrothermal conditioning. However, no changes on mechanical properties (tensile and compression strength) are observed for the Glare laminate, regardless the hygrothermal conditioning. (C) 2006 Elsevier Ltd. All rights reserved.

Influência da temperatura no desempenho mecânico de compósitos PEI/fibras de vidro

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Production of a low young modulus titanium alloy by powder metallurgy

Titanium alloys have several advantages over ferrous and non-ferrous metallic materials, such as high strengthto-weight ratio and excellent corrosion resistance. A blended elemental titanium powder metallurgy process has been developed to offer low cost commercial products. The process employs hydride-dehydride (HDH) powders as raw material. In this work, results of the Ti-35Nb alloy sintering are presented. This alloy due to its lower modulus of elasticity and high biocompatibility is a promising candidate for aerospace and medical use. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by isochronal sintering between 900 up to 1600 °C, in vacuum. Sintering behavior was studied by means of microscopy and density. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. Samples sintered at high temperatures display a fine plate-like alpha structure and intergranular beta. A few remaining pores are still found and density above 90% for specimens sintered in temperatures over 1500 °C is reached.

STUDY of THE TURNING NICKEL BASE ALLOY PYROMET (R) 31V (SAE HEV8)

Considering the constant technological developments in the aeronautical, space, automotive, shipbuilding, nuclear and petrochemical fields, among others, the use of materials with high strength mechanical capabilities at high temperatures has been increasingly used. Among the materials that meet the mechanical strength and corrosion properties at temperatures around 815 degrees C one can find the nickel base alloy Pyromet 31V (SAE HEV8). This alloy is commonly applied in the manufacturing of high power diesel engines exhaust valves where it is required high resistance to sulphide, corrosion and good resistance to creep. However, due to its high mechanical strength and low thermal conductivity its machinability is made difficult, creating major challenges in the analysis of the best combinations among machining parameters and cutting tools to be used. Its low thermal conductivity results in a concentration of heat at high temperatures in the interfaces of workpiece-tool and tool-chip, consequently accelerating the tools wearing and increasing production costs. This work aimed to study the machinability, using the carbide coated and uncoated tools, of the hot-rolled Pyromet 31V alloy with hardness between 41.5 and 42.5 HRC. The nickel base alloy used consists essentially of the following components: 56.5% Ni, 22.5% Cr, 2,2% Ti, 0,04% C, 1,2% Al, 0.85% Nb and the rest of iron. Through the turning of this alloy we able to analyze the working mechanisms of wear on tools and evaluate the roughness provided on the cutting parameters used. The tests were performed on a CNC lathe machine using the coated carbide tool TNMG 160408-23 Class 1005 (ISO S15) and uncoated tools TNMG 160408-23 Class H13A (ISO S15). Cutting fluid was used so abundantly and cutting speeds were fixed in 75 and 90 m/min. to feed rates that ranged from 0.12, 0.15, 0.18 and 0.21 mm/rev, and cutting depth of 0.8mm. The results of the comparison between uncoated tools and coated ones presented a machined length of just 30% to the first in relation to the performance of the second. The coated tools has obtained its best result for both 75 and 90 m/min. with feed rate of 0.15 mm/rev, unlike the uncoated tool which obtained its better results to 0.12 mm/rev.

Dynamics of meso and thermo citrate synthases with implicit solvation

The dynamics of hydration of meso and thermo citrate synthases has been investigated using the EEF1 methodology implemented with the CHARNM program. The native enzymes are composed of two identical subunits, each divided into a small and large domain. The dynamics behavior of both enzymes at 30 degrees C and 60 degrees C has been compared. The results of simulations show that during the hydration process, each subunit follows a different pathway of hydration, in spite of the identical sequence. The hydrated structures were compared with the crystalline structure, and the root mean square deviation (RMSD) of each residue along the trajectory was calculated. The regions with larger and smaller mobility were identified. In particular, helices belonging to the small domain are more mobile than those of the large domain. In contrast, the residues that constitute the active site show a much lower displacement compared with the crystalline structure. Hydration free energy calculations point out that Thermoplasma acidophilum citrate synthase (TCS) is more stable than chicken citrate synthase (CCS), at high temperatures. Such result has been ascribed to the higher number of superficial charges in the thermophilic homologue, which stabilizes the enzyme, while the mesophilic homologue denatures. These results are in accord with the experimental found that TCS keeps activity at temperatures farther apart from the catalysis regular temperature than the CCS. (c) 2005 Wiley Periodicals, Inc.

Straw decomposition of nitrogen-fertilized grasses intercropped with irrigated maize in an integrated crop-livestock system

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Empenamento, níveis hormonais de triiodotironina e tiroxina e temperatura corporal de frangos de corte de diferentes genótipos criados em diferentes condições de temperatura

Estudou-se o empenamento, os níveis hormonais de Triiodotironina (T3) e Tiroxina (T4) e a temperatura corporal de frangos criados em diferentes temperaturas. Foram alojados 180 pintainhos Cobb 500 e 180 pintainhos ISA Label JA57, em temperaturas termoneutra, quente ou fria. O delineamento utilizado foi inteiramente ao acaso, em modelo fatorial 2 x 3 (2 linhagens e 3 temperaturas) com 8 repetições. Houve um aumento das concentrações de T3, nas aves criadas no frio, e uma redução no calor. Também no calor, os frangos ISA Label apresentaram níveis mais altos de T4. As aves Cobb apresentaram uma redução de T4 no calor ou no frio aos 42 dias e no calor aos 21 dias de idade. Houve menor empenamento aos 42 dias, quando os frangos foram criados em alta temperatura e um menor empenamento das aves ISA Label, quando comparadas aos frangos Cobb. As aves criadas no calor apresentaram maior temperatura corporal. Os frangos Cobb apresentaram um aumento na sua temperatura interna, quando criados em ambiente quente. Já os frangos da linhagem ISA Label mantiveram sua temperatura interna, independentemente da temperatura ambiente. É possível concluir que a temperatura ambiente afeta o empenamento dos frangos de corte de linhagens de rápido ganho de peso, que também apresentaram menor tolerância ao calor, demonstrada através de uma maior temperatura corporal e temperatura interna.

Environmental factors influencing the transmission of Haemonchus contortus

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)