Tratamento da superfície do alumínio via eletrólise a plasma

This paper presents the study on the application of the electrolytic plasma for surface treatment of aluminum. A bibliographical study on the material of interest was preliminarily performed and later designed and built an electrolytic cell, including the excitation source. Unlike conventional electrolysis process, the plasma assisted carry on in the non-linear region of characteristic current/voltage curve. Therefore it requires for the on set of the process that the power supply operates on harder conditions than those on high current process. The plasma produced during the present investigation has temperatures in the range o 6,0.10 3 -7,0 .10 3 K, well above those found in conventional chemical process. It also shows a particular dynamic to promote changes on surface and to produce new materials. The plasma is generated by microdischarge in vapor or gas bubbles involved in physic-chemical processes in electrode regions of the electrolytic cell. The electrode material was the aluminum (7075). The Process Electrolytic Plasma Processing (EPP) is sensitive to various parameters such as operating voltage, current density, electrolyte, concentration of electrolyte, geometry of reactor, temperature of electrolytic solution and dynamic of the fluid in the cell. The experiments were carried on in order to find parameters for a stable abd steady operation. The choice for the electrolytic was silicate/alkali solution in various concentrations to operate in various voltage as well. Plasma was produced on negative (cathode) and positive (anode) electrode, in specific conditions. A stable operation on the cathode process was obtained with low concentration of the electrolytic in aqueous solution, current density around 250V effective voltage. For the evolution of plasma in anodic process it was required higher concentrations and higher... (Complete abstract click electronic access below)

Obtenção e caracterização de compósitos via RTM com alta fração de fibras de carbono processados à temperatura ambiente

After confirming the high specific mechanical properties of composite materials by scientific studies conducted over the last decades, one of the challenges of this new class of materials is the ability to achieve mass production at a more affordable cost, which has become indispensable. The Resin Transfer Molding (RTM) is an excellent method for manufacturing composite materials. Despite being a process widely used by international companies in the production of high performance structural composites, only a short time the national aviation industry has shown interest in implementing this type of processing to more complex structures and greater structural responsibility. In aeronautical projects, the reproducibility and the relative low cost of this process, several studies have been performed in Brazil for learning and perfecting this technique. This process is suitable for producing polymer components both simple as complex geometry, and allows to achieve consistent thickness, with high quality finish and without limiting range. Polymeric composite components for the high mechanical stress applications such as aircraft structures, satellites, etc., require a strict control of volume fractions of the composite constituents, beyond the knowledge of their mechanical and thermal properties. Therefore, in this experimental work degree study on the mechanical, thermal and of porosity composites processed by RTM processed characterization was performed. This characterization was performed targeting a possible aerospace application of this composite material. For the production of composites, process equipment (RTM RTM injector Radius 2100cc) was used. The processed carbono/epoxy composites were characterized via flexure tests mechanically and thermally analysis via DMA, DSC and TGA. To determine the volume fraction of fibers, the composite samples were analyzed via matrix digestion (ASTM D3171) ... (Complete abstract click electronic access below)

Fadiga em compósitos 5HS carbono/epóxi processados via RTM: relação entre cargas axiais no plano e modos de delaminação

Pós-graduação em Engenharia Mecânica - FEG

Oxidação de carboidratos via catálise metálica não enzimática para aplicação em sensores

This work has main aim of is to propose the synthesis and characterization of nanostructured materials for oxidation of carbohydrates such as glucose, with non-enzymatic catalysis. The proposed pathway of synthesis of metal catalysts is the polyol method and techniques of physical characterization proposals for analysis of prepared catalyst pass through diffraction technique of ray-x (DRX), scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy ray-x (EDX). Technical proposals for the electrochemical characterization of the synthesized catalysts are Cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The prospects of this work are compared by the catalytic activity of the sensor designed with non-enzymatic sensors and biosensors also known in the literature

Fotocromismo e luminescência de compostos a base de tungstênio e íons terras raras trivalentes via síntese hidrotérmica

Pós-graduação em Química - IQ

Análise estrutural de aerogéis via espalhamento de luz a baixo ângulo

The sol-gel process is a method for obtaining vitreous or vitro-ceramic materials which, are prepared a sol and by drying the liquid phase. This technique has been used extensively for the preparation of glassy gels, films, fibers and particles from the hydrolysis and polycondensation reactions of metal alkoxides. The usual methods for drying are: evaporation drying (xerogels), freeze drying (criogéis) and via supercritical CO2 extraction (aerogels). In the present work, we studied the preparation of silica gels by the sol-gel process from the hydrolysis of alkoxides tetraethylorthosilicate (TEOS) and 3-glycidoxypropyltrimethoxysilane (GPTS). The hydrolysis was promoted from GPTS and TEOS in proportion (4: 1) under acidic conditions. The hydrolysis reaction was promoted inside a Becker at room temperature. After hydrolyses the prepared sol had pH 2, and kept under mechanical agitation for a period of 1 hour. In order to accelerate the polycondensation reaction, the pH was corrected to a value near 5 by slowly adding NH4OH. Then the sols were leaked in sealed polycarbonate containers and maintained for 20 days at 40°C for gelation. Silica aerogels were prepared via supercritical CO2 extraction of the wet gel at temperature and pressure higher than 31°C and 74 atm, in an autoclave specially developed for the process. The structural characteristics were studied in the dry gel (aerogel). Aerogels were then characterized by nitrogen adsorption and small angle light scattering. The nitrogen adsorption data were analyzed for the determination of the BET specific surface (SBET), the total pore volume Vp, the pore mean size (lP=4Vp/SBET), the particle mean size (lS) and the pore size distribution (PSD). And the data from small angle light scattering were analyzed to determine the correlation function (γ'), the area per unit volume (S/V), average pore size (l ) and the average particle size...

Materiais híbridos de sílica/orgânico dopados com rodamina-B: estudo da luminescência e preparação de filmes finos para aplicações em fotônica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preparação e caracterização óptica de filmes de ORMOSIL obtidos via processo sol-gel dopados com azocorantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização e reciclagem química via pirólise de resíduos da fabricação de pás eólicas

A energia eólica é uma forma de energia que seu uso encontra-se em expansão, e junto a esse crescimento, tem-se também o aumento da quantidade de resíduos gerados na fabricação das pás eólicas. Uma forma correta de destinação e aproveitamento desses resíduos é a reciclagem. Porém, esses são constituídos de materiais compósitos, geralmente a resina epóxi e a fibra de vidro; e por possuírem um polímero termofixo (a resina epóxi) na sua composição, a reciclagem convencional via fusão não é possível. Desta forma, a reciclagem química via pirólise apresenta-se como uma alternativa para o aproveitamento desses resíduos, em especial da fibra de vidro que o contém. Após caracterização do resíduo de uma indústria de pás eólicas, verificou-se que se tratava de um material com mais de 70% de fibra de vidro e muito densas. Foram realizados ensaios de pirólise a seco e com óleo de babaçu, considerado o mais interessante perante vários possíveis e no qual o resíduo fica totalmente imerso, facilitando o inchamento e a troca de calor. Em um sistema de aquecimento com vácuo, foram obtidas mais de 97% de fibras em 30 minutos a 310 oC, justamente a temperatura em que uma análise termogravimétrica apontou ser a de início de altas taxas de degradação térmica.

Estudo estrutural, morfológico, elétrico e óptico de cristais de a-Ag2WO4 dopados com Mo6+ via co-precipitação assistida por PVP

Pós-graduação em Química - IQ

Carbendazim e modelos de biomembrana via filmes de Langmuir e Layer-by-Layer: mecanismos de interação e desenvolvimento de sensores

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

O efeito da ordenação e estrutura geométrica dos materiais PtSn/C e PdSn/C na eletrooxidação do glicerol em meio alcalino

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Detecção e quantificação eletroquímica de substâncias de interesse clínico, ambiental e forense utilizando eletrodo de pasta de grafite modificado com trisilanol poss ligado a suportes porosos e eletrodos impressos obtidos via screen-printed

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sínteses e caracterizações de materiais microporosos com estrutura cristalográfica mista e suas aplicações como catalisadores em reações de conversão de biomassa em produtos de química fina

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)