Analysis on turning Ti-6Al-4V with different cooling methods

The aim of this paper is to optimize the machining of Ti-6Al-4V alloy, by studying the chip formation, roughness and tool wear for different cooling conditions. The results were compared between cooling methods, minimal quantity of fluid (MQF) and flooding, and also without fluid for the tool H13A. The turning of Ti-6Al-4V has shown good results on roughness (0, 8μm) and tool life, which was 11% lower with MQF than with the flooding method. The tool wear causes variation of the shear angle, which promotes strength hardening of the chip. As a result, the machined surface could be damaged. The use of the cutting fluid helps to save the cutting edge and could reduce the strength hardening. Nevertheless, it could also facilitate the formation of built-up edge. The nucleation of alpha lamellar colonies can occur due to a combination of deformation rates and temperature, mainly when the flooding is used, but it's not conclusive. The lamellar colonies were also found with the MQF in some regions, however, this structure did not show hardness variation compared to equiaxial. For all this reasons, the machining parameters might be carefully chosen.

Effect of different methods of cutting fluid application on turning of a difficult-to-machine steel (SAE EV-8)

In this study, different methods of cutting fluid application are used in turning of a difficult-to-machine steel (SAE EV-8). Initially, a semisynthetic cutting fluid was applied using a conventional method (i.e. overhead flood cooling), minimum quantity of cutting fluid, and pulverization. A lubricant of vegetable oil (minimum quantity of lubricant) was also applied using the minimum quantity method. Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface, top surface of the chip (between workpiece and chip) and tool-workpiece contact. Moreover, two other methods were used: an interflow between conventional application and chip-tool interface jet (combined method) and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high-pressure system using a piston pump for generating a cutting fluid jet, a venturi for fluid application (minimum quantity of cutting fluid and minimum quantity of lubricant) and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. Among the results, it can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure, such as minimum quantity of volume and pulverization, when considering just the cutting tool wear. © 2013 IMechE.

Different methods of cutting fluid application on turning of a difficult-to-machine steel

Different methods of cutting fluid application are used on turning of a difficult-tomachine steel (SAE EV-8). A semi-synthetic cutting fluid was applied using a conventional method, minimum quantity of cutting fluid (MQCF), and pulverization. By the minimum quantity method was also applied a lubricant of vegetable oil (MQL). Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface; top surface of the chip; and tool-workpiece contact. Two other methods were used: an interflow between conventional application and chip-tool interface jet and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high pressure system using a piston pump for generating a cutting fluid jet, a Venturi for fluid application (MQCF and MQL), and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. It can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure. © (2013) Trans Tech Publications, Switzerland.

Sistema CIE Lab: análise computacional de fotografias

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effect of s/g ratio on kraft pulping and ecf bleaching of some poplars and eucalyptus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Internal Combustion Engine's Throttle Control as a Motivational Theme for Teaching Microprocessors Systems Lab Classes

The increased fuel economy and driveability of modern internal combustion engine vehicles (ICEVs) are the result of the application of advanced digital electronics to control the operation of the internal combustion engine (ICE). Microprocessors (and micro controllers) play a key role in the engine control, by precisely controlling the amount of both air and fuel admitted into the cylinders. Air intake is controlled by utilizing a throttle valve equipped with a motor and gear mechanism as actuator, and a sensor enabling the measurement of the angular position of the blades. This paperwork presents a lab setup that allows students to control the throttle position using a microcontroller that runs a program developed by them. A commercial throttle body has been employed, whereas a power amplifier and a microcontroller board have been hand assembled to complete the experimental setup. This setup, while based in a high-tech, microprocessor-based solution for a real-world, engine operation optimization problem, has the potential to engage students around a hands-on multidisciplinary lab activity and ignite their interest in learning fundamental and advanced topics of microprocessors systems.

A multiple intelligences theory-based 3D virtual lab environment for digital systems teaching.

This paper describes a 3D virtual lab environment that was developed using OpenSim software integrated into Moodle. Virtuald software tool was used to provide pedagogical support to the lab by enabling to create online texts and delivering them to the students. The courses taught in this virtual lab are methodologically in conformity to theory of multiple intelligences. Some results are presented.

Bacteriocinogenic LAB from cheeses - Application in biopreservation?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of CAD-CAM diamond bur deterioration on surface roughness and maximum failure load of Y-TZP-based restorations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of plant regulators on the growth and flowering of Saint Augustine grass plants

The objective of this work was to evaluate the effects of three plant growth inhibitors on the development and emission of floral rachis of Saint Augustine grass [Stenotaphrum secundatum (Walt.) Kuntzel] plants. The study was carried out in a 15 month old lawn with the experimental plots being distributed in accordance with a complete randomized block design with four replications. The treatments consisted of sole application of trinexapac-ethyl (113, 226, 452, 678, and 904 g ai ha(-1)), prohexadione-calcium (100 and 200 g ai ha(-1)), and bispyribac-sodium (40 and 60 g ai ha(-1)) plus a check treatment in which the plants were not submitted to any of the plant growth inhibitors. The effects of those products were evaluated in terms of visual signs of plant intoxication, plant height, emission and height of floral rachises, and chip total dry matter production. All the plant growth inhibitors resulted in visible injury to the plants but these intoxication signs practically disappeared 28 days after the application. Trinexapac-ethyl at the dose of 904 g ai ha(-1) reduced plant height by 59.7%, the emission of floral rachis by 96.4%, and the amount of chip dry matter production by 87.7%. Plant growth inhibitors may reduce the number of times of lawn plants cutting up to 119 days after their application with no harmful effects on the plants visual aspect.

Effect of different solutions on color stability of acrylic resin-based dentures

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of Nd:YAG or Er:YAG laser surface treatment on microtensile bond strength of indirect resin composites to resin cement. Lasers surface treatment of indirect resin composites

This study evaluated the influence of the surface pretreatment of indirect resin composite (Signum, Admira Lab and Sinfony) on the microtensile bond strength of a resin cement. Sixty samples made of each brand were divided into 6 groups, according to surface treatment: (1) control; (2) controlled-air abrasion with Al2O3; (3) Er:YAG Laser 200 mJ, 10 Hz, for 10s; (4) Er: YAG Laser 300 mJ, 10 Hz, for 10 s; (5) Nd:YAG 80 mJ, S15Hz for 1 min; (6) Nd:YAG 120mJ, 15 Hz for 1 min. After treatments, all the groups received an application of 37% phosphoric acid and adhesive. The pair of blocks of the same brand were cemented to each other with dual resin cement. The blocks were sectioned to obtain resin-resin sticks (1 x1 mm) and analyzed by microtensile bond testing. The bond strength values were statistically different, irrespective of the surface treatment performed, with highest values for Sinfony (43.81 MPa) and lowest values for Signum (32.33 MPA). The groups treated with the Nd:YAG laser showed the lowest bond strength values and power did not interfere in the results, both for Nd:YAG laser and Er:YAG. Controlled-air abrasion with Al203 is an efficient surface treatment method and the use of the Nd:YAG and Er:YAG lasers reduced bond strength, irrespective of the intensity of energy used.

Osmotic potentials on water uptake and germination of Guazuma ulmifolia Lam. (Sterculiaceae) seeds

Osmotic potentials on water uptake and germination of Guazuma Ulmifolia Lam. (Sterculiaceae) seeds. This work was carried out in the Germination Lab. of the Department of Botany, Institute of Biosciences, São Paulo State University (UNESP), Botucatu, São Paulo State, Brazil. The aims of this work were to determine the water uptake curve and to evaluate the germination of Guazuma ulmifolia seeds subjected to different water potentials. For the water uptake curve, seven replicates of 50 pre-scarified seeds were placed onto paper moistened with 15 mL PEG 6000 solution under the potentials 0 (control), -0.3 and -0.6 MPa at 25o C in the darkness. For the germination assay, four replicates of 50 seeds were subjected to the same above-described conditions; however, one lot of seeds was modified when there was variation in the refractometric index, whereas the remaining ones were kept in the same solutions until the end of the experiment. All three phases of water uptake were detected under 0 and -0.3 MPa; however, phase II was prolonged under -0.6 MPa and germination was not observed. For 0 and -0.3 MPa, the adopted statistical models consisted of asymptotic (phases I and II) and exponential (phase III) functions, y = a*[1 - b*exp (-c*t) + exp (-d + e*(t - t0)]. For -0.6MPa, only the asymptotic function y = a* [1 - b* exp (-c*t)] was used since there was no evidence of germination. The germination final percentage and speed index were lower under -0.3 MPa, mainly when solutions were not replaced; besides, germination was not detected under -0.6 MPa, with or without solution replacement.