Modelagem e simulação do mecanismo biela manivela e análise estrutural de biela automotiva

Nowadays, the automotive industry is working to optimize the design of engines, in order to reduce the fuel consumption with acceptable efficiency ratio. This undergraduate thesis is aimed at perform a kinematic/dynamic analysis of a slider-crank mechanism that is part of a four stroke internal combustion engine, the same engine that was used in the analysis described by Montazersadhd and Fatemi (2007). Two algorithms were developed based on Kane’s method to calculate velocities and accelerations of the mechanism bodies, and provide the acting forces at connecting rod joints. A SimMechanics model was developed to simulate the engine, and monitoring the same parameters that were calculated with the algorithms. The results obtained with both approaches were satisfactory and showed good agreement with the values provided by Montazersadhd and Fatemi (2007). The obtained results showed that the axial component of the rod joint efforts was caused by the pressure exerted on the piston head,whereas the radial component was related with the action of inertia loads. Besides, this thesis presents a connecting rod assembly mesh that is going to be used for static and fatigue finite element analysis in the future

Influência dos parâmetros de projeto em um motor a combustão interna

This paper discusses the influence of the design parameters in the operation and construction of an internal combustion engine. A theoretical analysis was developed using a standard crank-connecting rod-piston to verify the behavior of the stresses generated in the combustion and transformed into rotational energy of the crank shaft. Design parameters directly influence not only the final result of the characteristics of power and torque, but how the engine must be built to withstand different loads. The choice of parameters of a combustion engine is directly linked with the application of the engine and the final result expected of it function

Projeto e usinagem do cabeçote para um motor 4 tempos, a gasolina, monocilíndrico de 400 cc e refrigerado a ar

Pós-graduação em Engenharia Mecânica - FEG

Low variation in ribosomal DNA and internal transcribed spacers of the symbiotic fungi of leaf-cutting ants (Attini: Formicidae)

Leaf-cutting ants of the genera Atta and Acromyrmex (tribe Attini) are symbiotic with basidiomycete fungi of the genus Leucoagaricus (tribe Leucocoprineae), which they cultivate on vegetable matter inside their nests. We determined the variation of the 28S, 18S, and 5.8S ribosomal DNA (rDNA) gene loci and the rapidly evolving internal transcribed spacers 1 and 2 (ITS1 and ITS2) of 15 sympatric and allopatric fungi associated with colonies of 11 species of leafcutter ants living up to 2,600 km apart in Brazil. We found that the fungal rDNA and ITS sequences from different species of ants were identical (or nearly identical) to each other, whereas 10 GenBank Leucoagaricus species showed higher ITS variation. Our findings suggest that Atta and Acromyrmex leafcutters living in geographic sites that are very distant from each other cultivate a single fungal species made up of closely related lineages of Leucoagaricus gongylophorus. We discuss the strikingly high similarity in the ITS1 and ITS2 regions of the Atta and Acromyrmex symbiotic L. gongylophorus studied by us, in contrast to the lower similarity displayed by their non-symbiotic counterparts. We suggest that the similarity of our L. gongylophorus isolates is an indication of the recent association of the fungus with these ants, and propose that both the intense lateral transmission of fungal material within leafcutter nests and the selection of more adapted fungal strains are involved in the homogenization of the symbiotic fungal stock.

Internal Architecture and Population Size of Acromyrmex subterraneus molestans (Hymenoptera, Formicidae) Nests: Comparison Between a Rural and an Urban Area

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Chemical and microbiological evaluation of the internal surfaces of aluminum tubes both unlined and lined with epoxi resin by means of the stereoscope and scanning electron microscope

A superfície interna das bisnagas fabricadas com alumínio não revestido e revestido com resina epóxi, utilizadas para acondicionar cremes, pomadas, géis, etc., foram avaliadas quimicamente e por métodos microbiológicos correlacionados com a aderência de microrganismos. A prova da porosidade e da resistência à remoção da resina foi observada por meio do microscópio eletrônico de varredura (Topcon FM300) e estereoscópio Leica (MZ12) acoplado a Sistema de Digitalização de Imagens. Para avaliar a ação dos microrganismos foram utilizados corpos-de-prova esterilizados (discos de 10mm de diâmetro), imersos em caldo Mueller Hinton (Difco) e colocados em tubos de polipropileno com tampa de rosca (Corning). Foram inoculados tubos com meio de cultura para cada uma das suspensões bacterianas (10(9)UFC/mL) de Streptococcus agalactiae, Staphylococcus aureus, Acinetobacter lwoffii e Candida albicans, incubados a 37°C, sob agitação constante durante 12 dias. O meio de cultura era trocado a cada 3 dias. Após esse período, os corpos-de prova foram removidos, processados e observados em microscópio eletrônico de varredura JEOL-JSM (T330A). A observação por meio do microscopio eletrônico de varredura mostrou a aderência e a formação de biofilme sobre a superfície de alumínio não revestido e revestido com resina epóxi.

Phosphate forms in plant and their internal buffering in five soybean cultivars

Diferenças inter e intra-específicas na habilidade de suportar períodos de estresse nutricional podem dever-se à capacidade de armazenar e liberar íons dos vacúolos, e, ou, à intensidade de retranslocação de nutrientes em tais condições. Neste trabalho, pretendeu-se avaliar diferenças varietais quanto ao tamanho do pool não-metabólico de Pi; velocidade de liberação do Pi previamente armazenado (VLPi), quando o P citoplasmático cai a um valor limite; capacidade de transportar Pi de regiões menos ativas para aquelas mais ativas metabolicamente e definir compartimentos que são preferencialmente fontes e os que são preferencialmente drenos para o Pi, em condições de absorção limitada de P. Avaliaram-se a produção de matéria seca e os teores internos de Pi, orgânico (Po) e total solúvel em ácido (Pts), de diferentes órgãos de plantas dos cultivares de soja (Glycine max L. Merrill) Santa Rosa, Uberaba, IAC8, Doko e UFV1, submetidos a oito dias de omissão do elemento. A VLPi foi estimada como tangente às equações obtidas para Pi como função do perído de omissão no ponto médio do período de omissão em que houve maior decréscimo em Pi (zero a quatro dias de omissão de P), t = dois dias, considerando-se que -deltaPi/deltat expressa a velocidade de liberação de Pi. A capacidade interna de tamponamento de Pi (CTIPi) foi calculada como o inverso da VLPi. O cultivar Santa Rosa apresentou maior capacidade de armazenar Pi, quando o suprimento externo foi alto, liberando-o mais intensamente sob condições de baixo suprimento de P que os cultivares IAC8 e UFV1. O cultivar Uberaba mostrou-se superior ao Doko em sua habilidade de armazenar e utilizar o Pi. Folhas superiores mostraram ser o principal dreno para o Pi armazenado em folhas medianas e inferiores, seguidas por raízes e caules. Raízes comportaram-se como fontes ou drenos para o Pi. Raízes e folhas superiores apresentaram maiores (VLPi) e menores valores de CTIPi que folhas medianas e folhas inferiores, sendo o caule o compartimento com menor VLPi e maior CTIPi. Dentre as variedades, as diferenças foram pequenas, destacando-se a maior VLPi e menor CTIPi do cultivar Santa Rosa. O cultivar Doko apresentou a menor VLPi e maior CTIPi, enquanto Uberaba, IAC8 e UFV1 ocuparam posição intermediária quanto a essas características.

Study of interstitial oxygen mobility in RuSr2GdCu2O8 by internal friction

The discovery of the spatial uniform coexistence of superconductivity and ferromagnetism in ruthenocuprates, RuSr2GdCu2O8 (Ru-1212), has spurred an extraordinary development in the study of the competition between magnetism and superconductivity. However, several points of their preparation process and characterization that determine their superconductive behaviour are still obscure. The improvement of sample preparation conditions involves some thermal treatments in inert atmosphere. Anelastic spectroscopy measurements were made using an inverted torsion pendulum, operating with an oscillation frequency of 38 Hz, temperature in the 90 and 310 K range, heating rate of 1 K/min, and vacuum better than 10(-3) Pa. The results show anelastic relaxation peaks at 210 K related to the presence of interstitial oxygen atoms. The peaks decrease significantly with the oxygen loss caused by the heat treatments in vacuum, appearing again after the annealing of the sample in an oxygen atmosphere. These observed peaks are clearly related to the additional oxygen atoms, with activation energy 0.13 and 0.36 eV, and can be explained in terms by diffusional jumps of interstitial oxygen in the RuO2 planes. (C) 2009 Elsevier B.V. All rights reserved.

Evaluation of the thermal damages in inlet engine valves varying the grinding wheels and the cutting fluids

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Retrograde Endovascular Treatment of Internal Iliac Aneurysm in a Patient with Marfan Syndrome

To report a technique to maintain pelvic flow to an internal iliac artery (IIA) with aneurysm in a patient with Marfan syndrome, and previously treated by infrarenal abdominal aortic aneurysm open procedure. Retrograde endovascular hypogastric artery preservation (REHAP) through flexible endograft implantation from external iliac artery (EIA) to internal iliac artery (IIA) was used. REHAP was a reasonable, minimally invasive and elegant alternative (new) to maintain pelvic arterial flow in Marfan syndrome. However, the long-term durability is unknown, and so, it should be used in selected patients.

Internal carotid artery pseudoaneurysm after tonsillectomy treated by endovascular approach - A case report

Surgery on the head and neck region may be complicated by vascular trauma, caused by direct injury on the vascular wall. Lesions of the arteries are more dangerous than the venous one. The traumatic lesion may cause laceration of the artery wall, spasm, dissection, arteriovenous fistula, occlusion or pseudoaneurysm.We present a case of a child with a giant ICA pseudoaneurysm after tonsillectomy, manifested by pulsing mass and respiratory distress, which was treated by endovascular approach, occluding the lesion and the proximal artery with Histoacryl. We reinforce that the endovascular approach is the better way to treat most of the traumatic vascular lesions.

Comparison of the sequences of the internal transcribed Spacer regions and PbGP43 genes of Paracoccidioides brasiliensis from patients and armadillos (Dasypus novemcinctus)

Paracoccidioides brasiliensis isolates from 10 nine-banded armadillos (Dasypus novemcinctus) were comparable with 19 clinical isolates by sequence analysis of the PbGP43 gene and ribosomal internal transcribed spacer 1 (ITS1) and ITS2 and by random amplified polymorphic DNA. In this original ITS study, eight isolates differed by one or three sites among five total substitution sites.

Use of extensible internal device in the femur of young dogs

An extensible internal device (EID) was developed to preserve growth plate during the treatment of fracture complications or segmental bone loss from tumour resection in children. Since this type of extensible, trans-physeal, internal fixation device has only been used in a few paediatric cases; the aim of this study was to evaluate an in vivo canine study, a surgical application of this device, and its interference with longitudinal growth of the non-fractured distal femur. Ton clinically healthy two- to three-month-old poodles weighing 1.5-2.3 kg were used. Following a medial approach to the right distal femur, one extremity of the EID, similar to a T-plate, was fixed in the femoral condyle with two cortical screws placed below the growth plate. The other extremity, consisting of an adaptable brim with two screw holes and a plate guide, was fixed in the third distal of the femoral diaphysis with two cortical screws. The EID was removed 180 days after application. All of the dogs demonstrated full weight-bearing after surgery. The values of thigh and stifle circumferences, and stifle joint motion range did not show any difference between operated and control hindlimbs. The plate slid in the device according to longitudinal bone growth, in all but one dog. In this dog, a 10.5% shortening of the femoral shaft was observed due to a lack of EID sliding. The other dogs had the some longitudinal lengths in both femurs. The EID permits longitudinal bone growth without blocking the distal femur growth plate if appropriately placed.

Biomechanical evaluation of internal and external hexagon platform switched implant-abutment connections: An in vitro laboratory and three-dimensional finite element analysis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Identification of suitable internal control genes for expression studies in Coffea arabica under different experimental conditions

Background: Quantitative data from gene expression experiments are often normalized by transcription levels of reference or housekeeping genes. An inherent assumption for their use is that the expression of these genes is highly uniform in living organisms during various phases of development, in different cell types and under diverse environmental conditions. To date, the validation of reference genes in plants has received very little attention and suitable reference genes have not been defined for a great number of crop species including Coffea arabica. The aim of the research reported herein was to compare the relative expression of a set of potential reference genes across different types of tissue/organ samples of coffee. We also validated the expression profiles of the selected reference genes at various stages of development and under a specific biotic stress.Results: The expression levels of five frequently used housekeeping genes (reference genes), namely alcohol dehydrogenase (adh), 14-3-3, polyubiquitin (poly), beta-actin (actin) and glyceraldehyde-3-phosphate dehydrogenase (gapdh) was assessed by quantitative real-time RT-PCR over a set of five tissue/organ samples (root, stem, leaf, flower, and fruits) of Coffea arabica plants. In addition to these commonly used internal controls, three other genes encoding a cysteine proteinase (cys), a caffeine synthase (ccs) and the 60S ribosomal protein L7 (rpl7) were also tested. Their stability and suitability as reference genes were validated by geNorm, NormFinder and BestKeeper programs. The obtained results revealed significantly variable expression levels of all reference genes analyzed, with the exception of gapdh, which showed no significant changes in expression among the investigated experimental conditions.Conclusion: Our data suggests that the expression of housekeeping genes is not completely stable in coffee. Based on our results, gapdh, followed by 14-3-3 and rpl7 were found to be homogeneously expressed and are therefore adequate for normalization purposes, showing equivalent transcript levels in different tissue/ organ samples. Gapdh is therefore the recommended reference gene for measuring gene expression in Coffea arabica. Its use will enable more accurate and reliable normalization of tissue/organ-specific gene expression studies in this important cherry crop plant.