Estudo eletroquímico de revestimentos ambientalmente amigáveis aplicados para proteção da liga de alumínio 1200

Pós-graduação em Química - IQ

Investigação da condução elétrica em fitas duplas de dna imobilizadas em eletrodos de ouro por medidas eletroquímicas

Pós-graduação em Química - IQ

Desenvolvimento de biossensor eletroquímico para diagnóstico de dengue

Pós-graduação em Biotecnologia - IQ

Estudo eletroquímico e computacional de inibidores voláteis de corrosão adsorvidos sobre zinco

Pós-graduação em Química - IQ

Contribuições de Itaipu no processo de integração elétrica regional

Pós-graduação em Geografia - FCT

Desenvolvimento de imunossensor impedimétrico para detecção do corante disperso Red 1

Pós-graduação em Química - IQ

Desenvolvimento de um sistema para caracterização de dispositivos eletroluminescentes

The materials designed to be used in electroluminescent (EL) devices construction are studied and improved since 1936. Great interests in the development of this kind of devices are mainly due to its low power consumption, flexibility, low cost and easy processing. One class of ELs devices with these characteristics are produced by employing a organic-polymeric/inorganic composite from a conductive polymer blend and an inorganic electroluminescent material (Zn2SiO4:Mn) dispersed in the polymeric matrix. This kind of device operates in d.c. or a.c. potentials, with EL of hundreds candela in the green region of the visible spectrum. However, few studies on the light emission were performed for these devices. In order to characterize devices made from composites, in this work is proposed a method of characterizing the electroluminescence associated with the impedance spectroscopy technique. To implement the technique of impedance spectroscopy was employ an experimental setup consisting of a source of a.c. voltage, an oscilloscope, and a reference resistor. Associated with this system, was use a photo diode and an analog electrometer to characterize the emitted light signal from the sample. The system was implemented allows characterization by impedance spectroscopy in the frequency range from 0.2 Hz up to 2 MHz and voltage amplitudes of 5 mV up to 20 kV. This system permits, at the same time, measurement of the RMS value of the luminance for devices in frequency range from 20 Hz up to 2 MHz. To test the system efficiency, an EL device was characterized showing analogous results to those reported in literature. By doing this, was demonstrated the efficiency of the system for electroluminescence characterization associated with the electrical characterization by impedance spectroscopy, for devices

Determinação por meio de planejamento de experimentos da influência do lixamento nas medidas de dureza com durômetro portátil de método UCI

The hardness has an important role in quality control, in research studies and metallurgical and mechanical specification, selection and comparison of various materials. This property is of extreme importance in the oil industry because it is a determining factor to ascertain the safety of the material used in pressure vessels and pipelines. Due to the inability to stop the equipment while checking the hardness, the hardness testers are widely used portable method UCI, its great advantage is the fact that an essay fast, simple realization and not be considered a non-destructive testing with a good relationship money. The objective is to determine if there is significant difference in hardness measurements between 80 and 1200 sandpaper using a portable hardness tester UCI method, the material applied in gas storage spheres composition ASTM 516 Gr 70. After determining the number of homogeneity, we performed the hardness profile to isolate the major factors influencing the hardness part: cold rolling and segregation of impurities. Factors Cooling and sanding were analyzed using the method of design of experiments (DOE), in which it was demonstrated that neither variables nor their interactions, has significant influence on the hardness measurements by portable MIC 10. This fact will lead to reduction in time and cost for surface preparation

Avaliação das impedâncias em pontos de acupuntura

An experimental study in dogs was accomplished to evaluate impedances at the acupuncture points and the relative false points. According to the physics concepts and the Ohm’ Law, an electrical circuit was set up to determine the impedance. This circuit was introduced into three experiments in anesthetized dogs with needles at selected points. In the first two experiments, was applied an alternating tension with 200Hz frequency in the circuit and, in the last experiment, the frequency was increased to 10kHz, the tensions and electrical currents were measured between every pair of points for the all experiments. The impedances were calculated with the values obtained by experiments. The analysis of impedance values indicated that there is a coherent relation between the results and the applied frequencies in circuit, so just at high frequency condition admits the correct measurement of total impedance, therefore the last experiment gave the result which agreed with the theory, that the impedances at acupuncture points are lower than the impedances at false points

A influência da temperatura nas impedâncias de sequência de condutores utilizados na rede primária de distribuição

Distribution networks are formed by long lines that carry electricity substations to homes and industries. These lines have associated impedance and depending on operating conditions of the network these impedances may vary. This paper provides a detailed analysis of the effects observed in studies of voltage drop, short circuit and electrical losses, when considered the drivers sequence impedances used in primary distribution network at different temperatures. Therefore, it is initially presented a calculation methodology and details the factors that influence the final values. The methodology presented tackles in a practical way the main factors that directly or indirectly influence the values of the impedances as an emblematic example and will be properly dealt with throughout the paper is the effect of temperature on the values of the sequence impedances. More specifically is dealt with the case of XLPE cables protected, by having a higher maximum operating temperature than the operating temperature of the network. The effects observed in the power flow generated when considering the impedance values at both temperatures were analyzed. The impedance drivers tend to increase with increasing temperature. Thus the impedance of the conductor XLPE protected will tend to be greater for the maximum operating temperature for which the operating temperature of the network, resulting in greater voltage drop and higher electrical losses

Desenvolvimento de biossensores capacitivos constituídos de monocamadas peptídicas nanometricamente estruturadas

Pós-graduação em Biotecnologia - IQ

Espectroscopia de impedância eletroquímica da biodissolução da calcopirita na presença de íons ferrosos

Pós-graduação em Química - IQ

A mercantilização dos bens naturais no setor elétrico: o caso da UHE Barra Grande

Pós-graduação em Geografia - FCT

Detecção do vírus da cinomose canina por diferentes metodologias analíticas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades elétricas de materiais híbridos de Sílica/orgânico à base de GPTS/TEOS preparados pelo método sol-gel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)