Uniformidade de distribuição temporal e espacial do KCL na fertirrigação, em um sistema de irrigação por gotejamento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adubação com KCl revestido na cultura do milho no Cerrado

The use of coated potassium chloride can provide greater absorption of potassium resulting in the alteration of leaf contents, production components and grain yield. The objective of this study was to evaluate the effect of potassium doses using potassium chloride conventional or coated by polymer, in the corn crop under conditions of brazilian Savanna with low altitude. The experiment was conducted in Selviria, MS, Brazil, in a clayey Oxisol. The treatments consisted of four doses of K2O (0, 40, 80 and 120 kg ha(-1)), applied at sowing, and two sources: potassium chloride and potassium chloride coated by polymers. A randomized block design with eight treatments and four replications was used. The coated KCl is not efficient under the soil and climatic conditions studied, because it provided results similar to the conventional KCl for the K foliar content, crop components and grain yield of irrigated corn. The increment of K2O doses influenced positively the K and chlorophyll leaf contents, plant and spike insertion height and the number of rows and grains per spike. The maximum mean yield obtained was with 83.5 kg ha(-1) of K2O.

Hot turning of a difficult-to-machine steel (sae xev-f) aided by infrared radiation

A possible way for increasing the cutting tool life can be achieved by heating the workpiece in order to diminish the shear stress of material and thus decrease the machining forces. In this study, quartz electrical resistances were set around the workpiece for heating it during the turning. In the tests, heat-resistant austenitic alloy steel was used, hardenable by precipitation, mainly used in combustion engine exhaustion valves, among other special applications for industry. The results showed that in the hot machining the cutting tool life can be increased by 340% for the highest cutting speed tested and had a reduction of 205% on workpiece surface roughness, accompanied by a force decrease in relation to conventional turning. In addition, the chips formed in hot turning exhibited a stronger tendency to continuous chip formation indicating less energy spent in material removal process. Microhardness tests performed in the workpieces subsurface layers at 5 m depth revealed slightly higher values in the hot machining than in conventional, showing a tendency toward the formation of compressive residual stress into plastically deformed layer. The hot turning also showed better performance than machining using cutting fluid. Since it is possible to avoid the use of cutting fluid, this machining method can be considered better for the environment and for the human health.

Hot spots, hot moments, and spatio-temporal controls on soil CO2 efflux in a water-limited ecosystem

Soil CO2 efflux is the primary source of CO2 emissions from terrestrial ecosystems to the atmosphere. The rates of this flux vary in time and space producing hot moments (sudden temporal high fluxes) and hot spots (spatially defined high fluxes), but these high reaction rates are rarely studied in conjunction with each other. We studied temporal and spatial variation of soil CO2 efflux in a water-limited Mediterranean ecosystem in Baja California, Mexico. Soil CO2 efflux increased 522% during a hot moment after rewetting of soils following dry summer months. Monthly precipitation was the primary driver of the seasonal trend of soil CO2 efflux (including the hot moment) and through changes in soil volumetric water content (VWC) it influenced the relationship between CO2 efflux and soil temperature. Geostatistical analyses showed that the spatial dependence of soil CO2 efflux changed between two contrasting seasons (dry and wet). During the dry season high soil VWC was associated with high soil CO2 efflux, and during the wet season the emergence of a hot spot of soil CO2 efflux was associated with higher root biomass and leaf area index. These results suggest that sampling designs should accommodate for changes in spatial dependence of measured variables. The spatio-temporal relationships identified in this study are arguably different from temperate ecosystems where the majority of soil CO2 efflux research has been done. This study provides evidence of the complexity of the mechanisms controlling the spatio-temporal variability of soil CO2 efflux in water-limited ecosystems. (C) 2014 Elsevier Ltd. All rights reserved.

Diffusion of Lambda(c) in hot hadronic medium and its impact on Lambda(c)/D ratio

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo das características térmicas e mecânicas de formulações de adesivos PSA HOT MELT contendo variações de borrachas SBC e resinas taquificantes

The properties of the hot melt adhesive pressure sensitive (HMPSA) using an elastomer as a base polymer a copolymer of styrene and butadiene (SBS) and variation of tackifiers resins such as hydrocarbon resins and hydrogenated hydrocarbon were investigated. The formulations were prepared by mixing process within shear. The adhesives prepared were evaluated in test Brookfield viscosity and softening point Ring and Ball to compare the formulations and the influence of variations in raw materials. Infrared analyzes were performed to detect the reactions between the inputs and investigate the chemical interactions of the same properties of the adhesive. In thermal analysis, the assay was performed thermogravimetry (TG) and diferencial exploratory calorimetry (DSC). Were investigated the parameters of the tensile test on each of the formulations. Finally, were analysed comparatively the basic formulations of adhesives with their respective raw materials

Effect of adding a gonadotropin-releasing-hormone treatment at the beginning and a second prostaglandin F-2 alpha treatment at the end of an estradiol-based protocol for timed artificial insemination in lactating dairy cows during cool or hot seasons of the year

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

alpha-SiAlON-SiC composites obtained by gas-pressure sintering and hot-pressing

The objective of this work was the obtaining in situ of alpha-SiAlON-SiC composite, using an alternative rare-earth oxide mixture, RE2O3, as sintering additive, by two different sintering processes. As sintering additive, 20 vol.% of AlN-RE2O3 in a molar ratio of 90: 10 was mixed to the alpha-Si3N4 powder. In the Si3N4-AlN-RE2O3 powder mixture, 0, 10, 15 and 20wt.% of SiC were added. The powder batches were milled, dried and compacted by cold isostatic pressing. Two different sintering processes were used: gas-pressure sintering at 1950 degrees C for 1 h under 1.5 MPa of N-2 atmosphere, or uniaxial hot-pressing at 1750 degrees C, for 30 min under pressure of 20 MPa. The sintered samples were characterized by X-ray diffraction, scanning electron microscopy and mechanical properties. XRD patterns indicate only alpha-SiAlON (alpha') and beta-SiC as crystalline phases. It was observed that the SiC addition did not influence the alpha-SiAlON formation, although the growth of elongated alpha'-grains is substantially decreased. The hot-pressed composites presented better mechanical properties, exhibiting fracture toughness of 5 MPa m(1/2) and hardness around 21.5 GPa. (c) 2007 Elsevier B.V. All rights reserved.

Thermoregulatory responses of goats in hot environments

Notwithstanding the solar radiation is recognized as a detrimental factor to the thermal balance and responses of animals on the range in tropical conditions, studies on the amount of thermal radiation absorbed by goats therein associated with data on their production and heat exchange are still lacking. Metabolic heat production and the heat exchange of goats in the sun and in the shade were measured simultaneously, aiming to observe its thermal equilibrium. The results showed that black goats absorb twice as much as the white goats under intense solar radiation (higher than 800 W m(-2)). This observation leads to a higher surface temperature of black goats, but it must not be seen as a disadvantage, because they increase their sensible heat flow in the coat-air interface, especially the convection heat flow at high wind speeds. In the shade, no difference between the coat colours was observed and both presented a lower absorption of heat and a lower sensible heat flow gain. When solar radiation levels increases from 300 to 1000 W m(-2), we observed an increase of the heat losses through latent flow in both respiratory and cutaneous surface. Cutaneous evaporation was responsible for almost 90 % of the latent heat losses, independently of the coat colour. Goats decrease the metabolic heat production under solar radiation levels up to 800 W m(-2), and increase in levels higher than this, because there is an increase of the respiratory rate and of the respiratory flow, but the fractions of consumed oxygen and produced carbon dioxide are maintained stable. The respiratory rate of black goats was higher than the white ones, under 300 W m(-2) (55 and 45 resp min(-1)) and 1000 W m(-2) (120 and 95 resp min(-1), respectively). It was concluded that shade or any protection against solar radiation levels above 800 Wm(-2) is critical to guarantee goat's thermal equilibrium. Strategies concerning the grazing period in accordance with the time of the day alone are not appropriate, because the levels of radiation depend on the latitude of the location.

Fonte alternativa de K obtida da produção de KCl a partir da rocha silicática potássica (verdete) na cultura de milho

Para produzir o termopotássio e, até mesmo, o KCl, a rocha silicática potássica (verdete) passa pelo processo de calcinação. Neste processo é gerado um resíduo denominado coproduto que contém em sua composição química 3% a 4% de K2O, Ca, Mg e Si e apresenta baixa solubilidade em água. O presente trabalho objetivou testar a hipótese de que doses de K2O na forma de coproduto fornecem potássio para as plantas de milho em menor quantidade do que as mesmas doses na forma de KCl, inclusive no estudo do efeito residual, e que o potássio extraído do solo pela resina trocadora de íons tem maior correlação com as quantidades de potássio absorvida pela planta de milho do que com o potássio extraído pela solução extratora de Mehlich-1. O experimento foi conduzido em casa de vegetação, onde foram realizados dois cultivos consecutivos de milho em amostras de Neossolo Quartizarênico órtico. O delineamento foi em blocos casualizados com duas fontes de K (KCl e coproduto), três doses de K2O (0, 200 e 400 kg ha-1) e quatro repetições, totalizando 24 unidades experimentais. Foram determinados os teores de potássio extraído da amostra de solo pela solução extratora de Mehlich-1 e resina trocadora de íons, a produção de matéria seca da parte aérea das plantas de milho, os teores e o acumulo de potássio nas plantas após o primeiro e o segundo cultivo. Em dois cultivos consecutivos das plantas de milho, a aplicação de 200 e 400 kg ha-1 de K2O na forma de KCl proporcionou o acumulo de potássio na parte aérea das plantas de 77 e 84% maior do que aplicação dessas mesmas doses de K2O na forma de coproduto, respectivamente. A aplicação de 200 e 400 kg ha-1 de K2O na forma de coproduto proporcionou aumentos no acumulo de potássio da parte aérea das plantas de milho de 66 e 75% em relação ao controle (sem K2O), respectivamente. A recuperação de potássio pelas plantas de milho tratadas com KCl foi de 92% e as plantas...

Tribocorrosion behaviour of hot pressed CoCrMo−Al2O3 composites for biomedical applications

Alumina/alumina wear couple can lower the wear rates and thus metallic ion releasing on load bearing metallic implant materials. However, the low fracture toughness of ceramics is still a major concern. Therefore, the present study aims to process and to triboelectrochemically characterise the 5 and 10 vol.-%Al2O3 reinforced CoCrMo matrix composites. Corrosion and tribocorrosion behaviour of the composites were investigated in 8 g L−1 NaCl solution at body temperature. Corroded and worn surfaces were investigated by a field emission gun scanning electron microscope equipped with energy dispersive X-ray spectroscopy. After tribocorrosion experiments, wear rates were calculated using a profilometer. Results suggest that Al2O3 particle addition decreased the tendency of CoCrMo alloy to corrosion under both static and tribocorrosion conditions. However, no significant influence on the corrosion and wear rates was observed in composites mainly due to increased porosity and insufficient matrix/reinforcement bonding.

Experimental and numerical study of heat transfer in hot machined workpiece using infrared radiation

One of the greatest problems found in machining is related to the cutting tool wear. A way for increasing the tool life points out to the development of materials more resistant to wear, such as PCBN inserts. However, the unit cost of these tools is considerable high, around 10 to 20 times compared to coated carbide insert, besides its better performance occurs in high speeds requiring modern machine tools. Another way, less studied is the workpiece heating in order to diminish the shear stress material and thus reduce the machining forces allowing an increase of tool life. For understanding the heat transfer influences by conduction in this machining process, a mathematical model was developed to allow a simplified numerical simulation, using the finite element method, in order to determine the temperature profiles inside the workpiece.