Production grinding burn detection using acoustic emission and electric power signals

This work uses a monitoring system based on a PC platform, where the acoustic emission and electric power signals generated during the grinding process are used to investigate superficial burning occurrence in a surface grinding operation using two types of steel, three grinding conditions and an Al203 vitrified grinding wheel. Acoustic emission signals on the workpiece and grinding power were measured during a surface plunge operation until the grinding burn happened. From the results the standard deviation of the acoustic emission signal and the maximum electric power were calculated for each grinding pass. The proposed DPO parameter is the product between the power level and acoustic emission standard deviation. The results show that both signals can be used for burning detection, and the parameter DPO is the best indicator for the burning studied in this work. This can be explained by the high dispersion of the acoustic emission RMS level associated to the high power consumption when the grinding wheel lose its sharpness.

A high efficiency HPF-ZCS-PWM Sepic for electronic ballast with multiple tubular fluorescent lamps

This paper presents a high efficiency Sepic rectifier for an electronic ballast application with multiple fluorescent lamps. The proposed Sepic rectifier is based on a Zero-Current-Switching (ZCS) Pulse-Width-Modulated (PWM) soft-commutation cell. The high power-factor of this structure is obtained using the instantaneous average-current control technique, in order to attend properly IEC61000-3-2 standards. The inverting stage of this new electronic ballast is a classical Zero-Voltage-Switching (ZVS) Half-Bridge inverter. A proper design methodology is developed for this new electronic ballast, and a design example is presented for an application with five fluorescent lamps 40W-T12 (200W output power), 220Vrms input voltage, 130Vdc dc link voltage, with rectifier and inverter stages operating at 50kHz. Experimental results are also presented. The THD at input current is equal to 6.41%, for an input voltage THD equal to 2.14%, and the measured overall efficiency is about 92.8%, at rated load.

A novel programmable PFC based hybrid rectifier for ultra clean power application

A novel hybrid high power rectifier capable to achieve unity power factor is proposed in this paper. Single-phase SEPIC rectifiers are associated in parallel with each leg of three-phase 6-pulse diode rectifier resulting in a programmable input current waveform structure. In this paper it is described the principles of operation of the proposed converter with detailed simulation and experimental results. For a total harmonic distortion of the input line current (THDI) less than 2% the rated power of the SEPIC rectifiers is 33%. Therefore, power rating of the SEPIC parallel converters is a fraction of the output power, on the range of 20% to 33% of the nominal output power, making the proposed solution economically viable for high power installations, with fast pay back of the investment. Moreover, retrofits to existing installations are also possible with this proposed topology, since the parallel path can be easily controlled by integration with the already existing de-link. Experimental results are presented for a 3 kW implemented prototype, in order to verify the developed analysis.

Programmable PFC based hybrid multipulse power rectifier for utility interface of power electronic converters

In this paper it is proposed a novel hybrid three-phase rectifier capable to achieve high input power factor (PF), and low total harmonic distortion in the input currents (THDI). The proposed hybrid high power rectifier is composed by a standard three-phase 6-pulses diode rectifier (Graetz bridge) with a parallel connection of single-phase Boost rectifiers in each three-phase rectifier leg. Such topology results in a structure capable of programming the input current waveform and providing conditions for obtaining high input power factor and low harmonic current distortion. In order to validate the proposed hybrid rectifier, this paper describes its principles of operation, with detailed experimental results and discussions on power rating of the required Boost converters as related to the desired total harmonic current distortion. It is demonstrated that only a fraction of the output power is processed through the Boost converters, making the proposed solution economically viable for very high power installations, with fast pay back of the investment. Moreover, retrofitting to existing installations is also feasible since the parallel path can be easily controlled by integration with the existing de-link. A prototype rated at 6 kW has been implemented in laboratory and fully demonstrated its operation, performance and feasibility to high power applications. © 2005 IEEE.

Trolleybus power system for operation with AC or DC distribution networks

This paper presents the development and experimental analysis of a special input stage converter for a Trolleybus type vehicle allowing its operation in AC (two wires, single-phase) or DC distribution networks. The architecture of proposed input stage converter is composed by five interleaved boost rectifiers operating in discontinuous conduction mode. Furthermore, due to the power lines characteristics, the proposed input power structure can act as AC to DC or as DC to DC converter providing a proper DC output voltage range required to the DC bus. When operation is AC to DC, the converter is capable to provide high power factor with reduced harmonic distortion for the input current, complying with the restrictions imposed by IEC 61000-3-4 standard. Finally, the main experimental results are presented in order to verify the feasibility of the proposed converter, demonstrating the benefits and the possibility for AC feeding system for trolleybus type vehicle. © 2010 IEEE.

Bridgeless interleaved boost PFC converter with variable duty cycle control

This paper proposes a bridgeless boost interleaved PFC (power factor correction) converter with variable duty cycle control. The application of bridgeless technique causes reduction of conduction losses, while the interleaving technique of converters cells allows division of efforts in semiconductor devices and reduction of weight and volume of the input EMI filter. The use of variable duty cycle control has the functions of regulating the output voltage and eliminating the low order harmonic components that appears in the input current of the common interleaved power factor converters working in Discontinuous Conduction Mode (DCM). The simulation results of the proposed converter presented high power factor and a good transient response in relation to the output voltage regulation in presence of high load variations and supply voltage variations. © 2011 IEEE.

Investigação óptica de pontos quânticos de InAs confinados em poços quânticos de In0,15Ga0,85As

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Pré-regulador retificador entrelaçado (Interleaved) ZCS-FM boost, com controle digital através de dispositivo FPGA e linguagem VHDL

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise histopatológica comparativa de polpas humanas após confecção de cavidades de classe I com turbina de alta velocidade ou laser de Er:YAG

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Metallic nanoparticles grown in the core of femtosecond laser micromachined waveguides

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Can low-level laser therapy when associated to exercise decrease adipocyte area?

Obesity affects approximately 20% of the world population, and exercise is the primary non-pharmacological therapy. The combined use of exercise and low-level laser therapy (LLLT) may potentiate the effects promoted by exercise. The objective of this study was to investigate the effects of exercise in combination with phototherapy on adipocyte area, activity of the enzyme citrate synthase and muscle morphological analysis. We used 64 Wistar rats, which were divided into eight groups with 8 rats each: sedentary chow-diet (SC); sedentary chow-diet plus laser therapy (SCL), exercised chow-diet (EC); exercised chow-diet plus laser therapy (ECL); sedentary high-fat diet (SH); sedentary high-fat diet plus laser therapy (SHL); exercised high-fat diet (EH); exercised high-fat diet, laser therapy (EHL). The animals were submitted to a program of swimming training for 90min/5 times per week for 8weeks and LLLT (GA-Al-AS, 830nm) at a dose of 4.7J/point and a total energy of 9.4J/animal, with duration of 47s, which was applied to both gastrocnemius muscles after exercise. We conclude that the combined use of exercise and phototherapy increases the activity of the enzyme citrate synthase and decreases the white adipocyte area epididymal, retroperitoneal and visceral in obese rats, enhancing the effects of exercise.

Efeitos de lasers de alta potência na superfície de cerâmicas vítreas de dissilicato de lítio e sua resistência de união à dentina humana

Pós-graduação em Odontologia Restauradora - ICT