Flexural Strength of Glass-Infiltrated Zirconia/Alumina-Based Ceramics and Feldspathic Veneering Porcelains

Purpose: To compare the flexural strength of two glass-infiltrated high-strength ceramics and two veneering glass-ceramics.Materials and Methods: Four ceramic materials were tested: two glass-infiltrated high-strength ceramics used as framework in metal-free restorations [In-Ceram Zirconia IZ (Gr1) and In-Ceram Alumina IA (Gr2)], and two glass-ceramics used as veneering material in metal-free restorations [Vita VM7 (Gr3) and Vitadur-alpha (Gr4)]. Bar specimens (25 x 5 x 2 mm(3)) made from core ceramics, alumina, and zirconia/alumina composites were prepared and applied to a silicone mold, which rested on a base from a gypsum die material. The IZ and IA specimens were partially sintered in an In-Ceram furnace according to the firing cycle of each material, and then were infiltrated with a low-viscosity glass to yield bar specimens of high density and strength. The Vita VM7 and Vitadur-alpha specimens were made from veneering materials, by vibration of slurry porcelain powder and condensation into a two-part brass Teflon matrix (25 x 5 x 2 mm(3)). Excess water was removed with absorbent paper. The veneering ceramic specimens were then removed from the matrix and were fired as recommended by the manufacturer. Another ceramic application and sintering were performed to compensate the contraction of the feldspar ceramic. The bar specimens were then tested in a three-point bending test.Results: The core materials (Gr1: 436.1 +/- 54.8; Gr2: 419.4 +/- 83.8) presented significantly higher flexural strength (MPa) than the veneer ceramics (Gr3: 63.5 +/- 9.9; Gr4: 57.8 +/- 12.7).Conclusion: In-Ceram Alumina and Zirconia were similar statistically and more resistant than VM7 and Vitadur-alpha.

Effect of Acid Neutralization and Mechanical Cycling on the Microtensile Bond Strength of Glass-ceramic Inlays

Objectives: To evaluate the hypothesis that a process of hydrofluoric acid precipitate neutralization and fatigue load cycling performed on human premolars restored with ceramic inlays had an influence on microtensile bond strength results (MTBS). Methods: MOD inlay preparations were performed in 40 premolars (with their roots embedded in acrylic resin). Forty ceramic restorations were prepared using glass-ceramic (IPS Empress). The inner surfaces of all the restorations were etched with 10% hydrofluoric acid for 60 seconds, rinsed with water and dried. The specimens were divided into two groups (N=20): 1-without neutralization; 2-with neutralization. All the restorations were silanized and adhesively cemented (self-curing and self-etching luting composite system, Multilink). Ten premolars from each group were submitted to mechanical cycling (1,400,000 cycles, 50N, 37 degrees C). After cycling, the samples were sectioned to produce non-trimmed beam specimens (vestibular dentin-restoration-lingual dentin set), which were submitted to microtensile testing. Results: Bond strength was significantly affected by the surface treatment (p<0.0001) (no neutralization > neutralization) and mechanical cycling (p<0.0001) (control > cycling) (2-way ANOVA and Tukey test, alpha=.05). Conclusion: Hydrofluoric acid precipitate neutralization appears to significantly damage the resin bond to glass-ceramic and should not be recommended. The clinical simulation of the specimens, by using mechanical cycling, is important when evaluating the ceramic-dentin bond.

Surface degradation of glass ceramics after exposure to acidulated phosphate fluoride

Objective: This study evaluated the surface degradation effect of acidulated phosphate fluoride (APF) gel exposure on the glassy matrix ceramics as a function of time. Material and methods: Disc-shaped ceramic specimens (N = 120, 10/per ceramic material) were prepared in stainless steel molds (inner diameter: 5 mm, height: 2 mm) using 6 dental ceramics: 3 indicated for ceramic-fused-to-metal (Vita Omega 900, Carmen and Vita Titankeramik), 2 for all-ceramic (Vitadur Alpha and Finesse (R) Low Fusing) and 1 for both types of restorations (IPS d. SIGN). The specimens were wet ground finished, ultrasonically cleaned and auto-glazed. All specimens were subjected to calculation of percentage of mass loss, surface roughness analysis and topographical description by scanning electron microscopy (SEM) before (0 min) and after exposure to 1.23 % APF gel for 4 min and 60 min representing short-and long-term etching effect, respectively. The data were analyzed using two-way ANOVA with repeated measures and Tukey` s test (alpha=0.05). Results: Significant effect of the type of the ceramics (p=0.0000, p=0.0031) and exposure time (p=0.0000) was observed in both surface roughness and percentage of mass loss values, respectively. The interaction factor between both parameters was also significant for both parameters (p=0.0904, p=0.0258). Both 4 min (0.44 +/- 0.1-0.81 +/- 0.2 mu m) and 60 min (0.66 +/- 0.1 - 1.04 +/- 0.3 mu m) APF gel exposure created significantly more surface roughness for all groups when compared to the control groups (0.33 +/- 0.2-0.68 +/- 0.2 mu m) (p<0.05). There were no significant differences in percentage of mass loss between the ceramics at 4 min (p>0.05) but at 60 min exposure, IPS d. SIGN showed the highest percentage of mass loss (0.1151 +/- 0.11). The mean surface roughness for Vita Titankeramik (0.84 +/- 0.2 mu m) and Finesse (R) Low Fusing (0.74.+/- 0.2 mu m) was significantly higher than those of the other ceramics (0.59 +/- 0.1 mu m - 0.49 +/- 0.1 mu m) and Vita Titankeramik (p<0.05) regardless of the exposure time. A positive correlation was found between surface roughness and percentage of mass loss for all ceramic materials [(r=0.518 (Vitadur Alpha), r=0.405 (Vita Omega 900), r=0.580 (Carmen), r=0.687 (IPS d. SIGN), r=0.442 (Finesse (R) Low Fusing), r=0.572 (Vita Titankeramik), Pearson's correlation coefficient)]. The qualitative SEM analysis showed evidence of corrosive attack on all of ceramics at varying degrees. Conclusions: The ceramics indicated for either metal-ceramic or all-ceramic restorations were all vulnerable to surface texture changes and mass loss after short-term and long-term APF gel exposure.

Mechanical and thermal cycling effects on the flexural strength of glass ceramics fused to titanium

This study evaluated the effects of mechanical and thermal cycling on the flexural strength (ISO 9693) of three brands of ceramics fused to commercially pure titanium (cpTi). Metallic frameworks of 25 x 3 x 0.5 mm dimensions (N = 84) were cast in cpTi, followed by 150-mu m aluminum oxide airborne particle abrasion at a designated area of the frameworks (8 x 3 mm). Bonder and opaque ceramic were applied on the frameworks, and then the corresponding ceramic (Triceram, Super Porcelain Ti-22, Vita Titankeramik) was fired onto them (thickness: 1 mm). Half of the specimens from each ceramic-metal combination were randomly tested without aging (only water storage at 37 degrees C for 24 hours), while the other half were mechanically loaded (20,000 cycles under 10 N load, immersion in distilled water at 37 degrees C) and thermocycled (3,000 cycles, between 5-55 degrees C, dwell time of 13 seconds). After the flexural strength test, failure types were noted. Mechanical and thermal cycling decreased the mean flexural strength values significantly (p<0.05) for all the three ceramic-cpTi combinations tested when compared to the control group. In all the three groups, failure type was exclusively adhesive at the opaque ceramic-cpTi interfacial zone with no presence of ceramic on the substrate surface except for a visible oxide layer.

Multi-criteria spatial decision analysis for demarcation of greenway: A case study of the city of Rio Claro, São Paulo, Brazil

Concern regarding hydrological resources has been a theme of growing importance in Brazil, associating the development of new management policies and maintenance of natural areas related to rivers. An efficient way to maintain natural areas around rivers has been the development of greenways, and some cites have already adopted specific legislation in this respect. Following this growing evolution in the treatment of hydrological resources, this study was carried out to demarcate a greenway along the Corumbatai River in the state of São Paulo, Using multi-criteria analysis in a GIS environment. First, thematic maps were elaborated based on Landsat 7 satellite, aerial photographs and digital topographic base, Supported by field activities. With the use of multi-criteria analysis, for which ad hoe consultations were conducted to attribute weights to the thematic maps, a suitability map was elaborated for the allocation of the greenway. Sites that should be included in the greenway were also selected, such as areas appropriate for leisure activities, and ecologically important areas. Based on the suitability map, a pathway analysis was done, connecting the relevant points of interest, thus generating a greenway that runs along the Corumbatai River, with the aim of contributing to the conservation of this important hydrological resource. (c) 2007 Elsevier B.V. All rights reserved.

Structural Investigations of Glass Ceramics in the Ga2S3-GeS2-CsCl System

Transparent glass ceramics have been prepared in the Ga2S3-GeS2-CsCI pseudoternary system appropriate heat treatment time and temperature. In situ X-ray diffraction at the heat treatment temperature and Cs-133 and Ga-71 solid-state nuclear magnetic resonance have been performed in function of annealing time to understand the crystallization process. Both techniques have evidenced the nucleating agent role played by gallium with the formation of Ga2S3 nanocrystals. on the other hand, cesium is incorporated very much later into the crystallites during the ceramization. Moreover, the addition of CsCl, which is readily integrated into the glassy network, permits us to shift the optical band gap toward shorter wavelength. Thus, new glass ceramics transmitting in the whole visible range up to 11.5 mu m have been Successfully synthesized from the (Ga2S3)(35)-(GeS2)(25)-CsCl40 base glass composition.

Medicinal plants used by "Passo da Ilha" rural community in the city of Pato Branco, southern Brazil

O objetivo deste trabalho foi resgatar e documentar o conhecimento popular referente às plantas medicinais utilizadas na comunidade rural do Passo da Ilha, em Pato Branco-PR (26° 11' S, 52°36' W e 760 m de altitude). Optou-se por utilizar o modelo de entrevista estruturada com 16 informantes, os quais possuíam o conhecimento sobre o uso das plantas medicinais em suas famílias. O período da realização das entrevistas foi de outubro a dezembro de 2000. As plantas foram coletadas no campo, identificadas e vouchers foram depositados no Herbário Irina Delanova de Gemtchjnicov (BOTU) da Universidade Estadual Paulista, em Botucatu-SP. Foram identificadas 47 famílias botânicas e 114 espécies de plantas medicinais. Estas plantas foram indicadas para mais de 30 usos medicinais diferentes. A comunidade é composta na maioria por descendentes de europeus, justificando a presença de muitas plantas exóticas. O domínio do uso das plantas é feminino, porém o conhecimento é menor nas gerações mais novas, denotando um processo de erosão cultural.

Epidemiological aspects of enteroparasitosis at daycare centers in the city of Botucatu, State of São Paulo, Brazil

Estimou-se a prevalência e a incidência de parasitas intestinais em crianças e funcionários de 5 creches municipais em Botucatu/SP. Foram realizados dois estudos seccionais em 2002 (N=379) e 2003 (N=397) e um estudo longitudinal observacional, onde as crianças de 2002 e 2003 foram seguidas por um ano. Foram aplicados questionários nos funcionários e nos pais das crianças, onde foram coletadas as seguintes variáveis: nível sócio-econômico, hábitos sanitários, moradia, idade, sexo e presença de animais domésticos. Foram realizados exames coproparasitológicos nas crianças das creches. A prevalência de enteroparasitas em 2002 foi de 76,74% e 34% em 2003. As variáveis associadas à presença de enteroparasitas no ano de 2002 foram: localização das creches (OR=0,27 IC=0,15-0,47), renda familiar (OR=4,38 IC=1,91-10,04), sexo (OR=0,52 IC=0,32-0,85), faixa etária (OR=2,08 IC=1,06-4,08) e presença de animais domésticos na casa (OR=1,85 IC=1,10-3,11); em 2003, as variáveis foram: creche localizada em bairro periférico (OR=0,49 IC=0,31-0,78), renda familiar (OR=3,69 IC=2,19-6,24), nível educacional da mãe (OR=6,19 IC=1,81-21,21), sexo (OR=0,36 IC=0,36-0,93) e presença de animais domésticos (OR=1,68 IC=1,01-2,79). A coorte foi integrada por 253 crianças apresentando incidência de 23,22%. Os dados deste estudo evidenciam situações de risco em populações específicas (creches) e poderiam ser utilizados por Instituições que promovem o cuidado com as crianças.

Spatial distribution of dengue in the city of Cruzeiro, São Paulo State, Brazil: use of geoprocessing tools

Este artigo tem por objetivo identificar padrões na distribuição espacial dos casos de dengue ocorridos no município de Cruzeiro/SP, no ano de 2006. Trata-se de um estudo ecológico e exploratório que utiliza as ferramentas de análise espacial na elaboração de mapas temáticos, com dados obtidos do SinanNet. Foi feita uma análise por área, tomando-se como unidade o setor censitário do IBGE; a análise considerou quatro meses do ano de 2006 que mostra a ocorrência da doença no município. Os mapas temáticos foram construídos pelo programa computacional TerraView 3.3.1; assim como os valores dos índices de Moran Global (I M) mês a mês e o estimador de Kernel. Foram georreferenciados 691 casos de dengue (taxa de 864,2 casos/100.000 habitantes); os Índices de Moran e p-valores obtidos foram I M = 0,080 (março) p = 0,11; I M = 0,285 (abril) p = 0,01; I M = 0,201 (maio) p = 0,01 e I M = 0,002 (junho) p = 0,57. Os primeiros casos foram identificados na região nordeste e central e os últimos casos, na região norte, nordeste e central. Foi possível identificar os setores censitários onde a epidemia teve início e como ocorreu têmporo-espacialmente no município.

Demographic determinants of survival of people living with HIV attending an outpatient reference unit in the city of Três Lagoas, state of Mato Grosso do Sul, Brazil, in the period 1984-2009

,,,,,,,,,, While the incidence of HIV infection and AIDS is increasing in small Brazilian cities, epidemiological studies are often conducted in large urban centers. ,,,,,,,,,,,,,,,,,, Our group conducted a retrospective analysis of survival determinants among 358 patients who attended a reference unit in a small city.,,,,,,,,,,,,,,,,,,,,,,,Death risk was lower among men that had sex with men, patients with an HIV-seropositive partner, and those admitted after highly active antiretroviral therapy (HAART) was available. ,,,,,,,,,,,,,,,,,, The study documents the striking beneficial effect of HAART. The finding of other groups with improved survival may aid in the development of programmatic strategies.,,,,

Changes of physical properties of glass surfaces exposed to KNO3 vapors

Modifications of glass surfaces were studied after exposure of samples to an atmosphere resulting from the decomposition of molten KNO3. The diffusion coefficient of K+ ions migrating into the surfaces of float glass and synthesized glasses doped with up to 5 wt% SnO2 was calculated by the Boltzmann-Matano technique. The Vickers hardness and the refractive index increase with exposure time. Infrared spectra show that the migration of K+ is responsible for an increase in the number of non-bridging oxygens in the exposed samples. The spectra of the synthesized glasses present evidences that their surfaces undergo crystallization during the exposure. All results lead to the conclusion that the presence of tin in the glasses hinders the diffusion of K+ ions, thus affecting the Vickers hardness, the refractive index and the infrared spectra. It is shown that the exposure method can be used as an alternative process to promote the K+ migration into glass surfaces. (c) 2006 Elsevier B.V. All rights reserved.

Correlation models of diffuse solar-radiation applied to the city of São Paulo, Brazil

Measurements of global and diffuse solar-radiation, at the Earth's surface, carried out from May 1994 to June 1999 in São Paulo City, Brazil, were used to develop correlation models to estimate hourly, daily and monthly values of diffuse solar-radiation on horizontal surfaces. The polynomials derived by linear regression fitting were able to model satisfactorily the daily and monthly values of diffuse radiation. The comparison with models derived for other places demonstrates some differences related mainly to altitude effects. (C) 2002 Elsevier B.V. Ltd. All rights reserved.