Effect of Airborne-Particle Abrasion and Mechanico-Thermal Cycling on the Flexural Strength of Glass Ceramic Fused to Gold or Cobalt-Chromium Alloy

Purpose: To evaluate the effect of airborne-particle abrasion and mechanico-thermal cycling on the flexural strength of a ceramic fused to cobalt-chromium alloy or gold alloy.Materials and Methods: Metallic bars (n = 120) were made (25 mm x 3 mm x 0.5 mm): 60 with gold alloy and 60 with Co-Cr. At the central area of the bars (8 mm x 3 mm), a layer of opaque ceramic and then two layers of glass ceramic (Vita VM13, Vita Zahnfabrick) were fired onto it (thickness: 1 mm). Ten specimens from each alloy group were randomly allocated to a surface treatment [(tungsten bur or air-particle abrasion (APA) with Al(2)O(3) at 10 mm or 20 mm away)] and mechanico-thermal cycling (no cycling or mechanically loaded 20,000 cycles; 10 N distilled water at 37 degrees C and then thermocycled 3000 cycles; 5 degrees C to 55 degrees C, dwell time 30 seconds) combination. Those specimens that did not undergo mechanico-thermal cyclingwere stored inwater (37 degrees C) for 24 hours. Bond strength was measured using a three-point bend test, according to ISO 9693. After the flexural strength test, failure types were noted. The data were analyzed using three factor-ANOVA and Tukey's test (alpha = 0.05).Results: There were no significant differences between the flexural bond strength of gold and Co-Cr groups (42.64 +/- 8.25 and 43.39 +/- 10.89 MPa, respectively). APA 10 and 20 mm away surface treatment (45.86 +/- 9.31 and 46.38 +/- 8.89 MPa, respectively) had similar mean flexural strength values, and both had significantly higher bond strength than tungsten bur treatment (36.81 +/- 7.60 MPa). Mechanico-thermal cycling decreased the mean flexural strength values significantly for all six alloy-surface treatment combinations tested when compared to the control groups. The failure type was adhesive in the metal/ceramic interface for specimens surface treated only with the tungsten bur, and mixed for specimens surface treated with APA 10 and 20 mm.Conclusions: Considering the levels adopted in this study, the alloy did not affect the bond strength; APA with Al(2)O(3) at 10 and 20 mm improved the flexural bond strength between ceramics and alloys used, and the mechanico-thermal cycling of metal-ceramic specimens resulted in a decrease of bond strength.

Surface characterization of feldspathic ceramic using ATR FT-IR and ellipsometry after various silanization protocols

Objectives. This study characterized the feldspathic ceramic surfaces after various silanization protocols.Methods. Ceramic bars (2 mm x 4 mm x 10 mm) (N = 18) of feldpathic ceramic (VM7, VITA Zahnfabrik) were manufactured and finished. Before silane application, the specimens were ultrasonically cleaned in distilled water for 10 min. The ceramic specimens were randomly divided into nine groups (N = 2 per group) and were treated with different silane protocols. MPS silane (ESPE-Sil, 3M ESPE) was applied to all specimens and left to react at 20 degrees C for 2 min (G20). After drying, the specimens were subjected to heat treatment in an oven at 38 degrees C (G38), 79 degrees C (G79) or 100 degrees C (G100) for 1 min. Half of the specimens of each group were rinsed with water at 80 degrees C for 15 s (G20B, G38B, G79B, G100B). The control group (GC) received no silane. Attenuated total reflection infrared Fourier transform analysis (ATR FT-IR) was performed using a spectrometer. Thickness of silane layer was measured using a spectroscopic ellip-someter working in the lambda = 632.8 nm (He-Ne laser) at 70 degrees incidence angle. Surface roughness was evaluated using an optical profilometer. Specimens were further analyzed under the Scanning Electron Microscopy (SEM) to observe the topographic patterns.Results. ATR FT-IR analysis showed changes in Si-O peaks with enlarged bands around 940 cm(-1). Ellipsometry measurements showed that all post-heat treatment actions reduced the silane film thickness (30.8-33.5 nm) compared to G20 (40 nm). The groups submitted to rinsing in hot water (B groups) showed thinner silane films (9.8-14.4 nm) than those of their corresponding groups (without washing) (30.8-40 nm). Profilometer analysis showed that heat treatments (Ra approximate to 0.10-0.19 mu m; Rq approximate to 0.15-0.26 mu m) provided a smoother surface than the control group (Ra approximate to 0.48 mu m; Rq approximate to 0.65 mu m). Similar patterns were also observed in SEM images.Significance. Heat treatment after MPS silane application improved the silane layer network. Rinsing with boiling water eliminated the outmost unreacted regions of the silane yielding to thinner film thicknesses. (C) 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

River avulsions on the Taquari megafan, Pantanal wetland, Brazil

The Pantanal wetland is located in a tectonically active interior sedimentary basin in west-central Brazil. The south-flowing Paraguay River is the trunk-river of an alluvial constructional landform comprising several large alluvial fans, the largest one of which is the Taquari megafan. The Taquari River flows in two distinct geomorphologic zones within the megafan. Entrenched on sediments of Pleistocene fan lobes, the Taquari River flows in a 3 to 5 km wide meander belt in the upper fan, where avulsion is hindered by entrenchment. Downstream of the intersection point, stream discharge progressively decreases and the Taquari River becomes narrow and shallow toward the Paraguay River plain. Within the distributary fan lobe, the channel-levee sandy complex is topographically higher than the adjacent floodplains and avulsion is a natural consequence of crevasses in the natural levees. Many channel avulsions have occurred during the last decades and documented cases show that significant channel changes may take place in a few years. Beginning with crevassing in 1988 and ending with the abandonment of the former channel in 1998, the river completely changed course in the lower fan. Presently, a major avulsion is occurring in the upper portion of the growing fan lobe, where many crevasses have appeared in the natural levees with associated splays onto the floodbasin. New anastomosed channels have formed north of the Taquari River, but downstream of them the flow is unconfined and the water spreads into natural floodbasins. This avulsion is still in process and allows observation of channel evolution, the geomorphic features produced, the sedimentary processes involved, and resulting effects. If the new channels do not rejoin the main channel, the river mouth may abandon its present master channel and shift to a position a hundred kilometers north from its present position. A large volume of sediment has been transferred to the floodbasin, with progradation of crevasse splay deposits over fine overbank sediments. Many geomorphic features, recognizable in satellite and radar images, clearly show that avulsion has occurred many limes before in the Taquari River. Avulsion belt deposits and former diverted channels testify to ancient avulsion events within the fan lobe and show that progradation of splays onto the floodbasin is the most important infilling process within the Taquari distributary fan lobe. The avulsion process in the lower Taquari River has accelerated in the last 30 years, along with the magnitude of flooding. Pasture and intensive agriculture in the catchment area has increased the sediment supply to the wetland, but larger floods are also a consequence of higher rainfall since 1973. Avulsion and floods have been a cause of great concern among the local population and landowners. Before human intervention in attempting to control floods, however, a better understanding of the avulsive river system is needed, especially because a major navigation project including the channelization of the Paraguay River was recently proposed. (c) 2005 Elsevier B.V. All rights reserved.

Remote sensing analysis of depositional landforms in alluvial settings: Method development and application to the Taquari megafan, Pantanal (Brazil)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Contrasting fluvial styles of the Paraguay River in the northwestern border of the Pantanal wetland, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tectonics and paleogeography of the Marajó Basin, northern Brazil

A área da Bacia do Marajó apresenta feições geológicas e geomorfológicas devidas principamente à distensão Mesozóica e à neotectônica pós-miocênica. O evento de distensão, com fases do Cretáceo Inferior e Superior, originou quatro sub-bacias que contituem a Bacia do Marajó, com uma espessa seqüência clástica continental mostrando influência marinha. Falhas normais NW e NNW e direcionais NE e ENE controlaram a geometria da bacia. A distensão, relacionada com a abertura do Atlântico Equatorial, propagou-se continente adentro ao longo de zonas de fraqueza crustal dos cinturões orogênicos pré-cambrianos Tumucumaque, Amapá e Araguaia. O evento neotectônico é um regime transcorrente que desenvolveu bacias transtensivas preenchidas por sedimentos marinhos rasos (Formação Pirabas) e seqüências transicionais (Grupo Barreiras) do Terciário Superior, seguidos por depósitos fluviais e seqüências transicionais do Quaternário, derivadas dos rios Amazoans e Tocantins e do estuário do Marajó. A paisagem atual tem morfologia tipicamente estuarina. A morfologia costeira apresenta escarpas em seqüências transicionais do Terciário Superior, enquanto no interior dominam elevações sustentadas por crosta laterítica do Pleistoceno Médio, aparadas por superfície erosiva a 70 m. No leste da Ilha do Marajó são reconhecidas várias gerações de paleocanais com seqüências estuarinas associadas, enquanto no lado oeste predomina uma planície flúvio-marinha.

Characidium xanthopterum (Ostariophysi: Characiformes: Crenuchidae): a new species from the Central Brazilian Plateau

Characidium xanthopterum é descrita de tributários das bacias do alto Paraná e do alto Tocantins, no Planalto Central do Brasil, Estado de Goiás, Brasil. Entre as congêneres, a nova espécie é diagnosticada pela ausência de barras escuras nas porções laterais do corpo em exemplares adultos, e pela presença de todas as nadadeiras fortemente amareladas, sem marcas ou manchas. Exemplares menores de 32 mm CP apresentam barras escuras no corpo. Estas barras desaparecem com o crescimento entre 32 e 35 mm CP, e estão sempre ausentes em indivíduos maiores do que 35 mm CP.

Análise morfométrica da rede de drenagem da bacia do Rio do Machado-MG

Este artigo visa analisar a rede de drenagem através da utilização das técnicas de Índice Relação Declividade e Extensão do Curso de Água (RDE) e análise do perfil longitudinal dos vales, numa região chave do Planalto Sul de Minas, a fim de contribuir com estudos sobre evolução da paisagem da região sudeste do Brasil. A pesquisa foi realizada na Bacia Hidrográfica do Rio do Machado (MG), afluente do Alto Rio Grande, e regiões adjacentes, localizadas no Planalto Sul de Minas. O Rio do Machado apresenta uma particularidade em seu curso, com uma mudança brusca de direção tomada por sua drenagem na área próxima ao seu médio curso. Com a aplicação das técnicas pretende-se compreender melhor a dinâmica do relevo na área, identificando áreas com indício de ação neotectônica e seu padrão de distribuição na bacia.

Modelos de paisagem e susceptibilidade magnética na identificação e caracterização do solo

O conhecimento detalhado do solo e de seus atributos, ao longo da paisagem, é uma demanda permanente dos sistemas urbanos e agroindustriais, para o planejamento sustentável de uso e ocupação. O presente trabalho objetivou estudar o potencial de modelos de paisagem e susceptibilidade magnética na identificação e caracterização de latossolos, em Guariba (SP). Foram coletadas 514 amostras de solo, em 110,0 ha, às profundidades de 0,0-0,20 m e 0,60-0,80 m. Foram identificados diferentes compartimentos de paisagem, com base no modelo de superfície geomórfica e segmento de vertente. em cada compartimento de paisagem, foram abertas trincheiras, para classificação do solo. As amostras foram analisadas quanto à granulometria e atributos químicos, pH (água, CaCl2 e KCl), matéria orgânica, P extraível, K+, Ca2+, Mg2+ e H+ + Al3+. Também foram determinados os teores de SiO2, Al2O3, Fe2O3 e óxidos de Fe livres (Fe d) e pouco cristalizados (Fe o), nas amostras das trincheiras, além da susceptibilidade magnética (SM). Solos taxonomicamente iguais, porém em diferentes compartimentos da paisagem, apresentaram valores distintos, para os atributos estudados, indicando que os modelos de paisagem e a susceptibilidade magnética podem ser viáveis, como técnica de campo, para auxiliar no detalhamento da variação dos atributos do solo. A susceptibilidade magnética demonstrou ter potencial para delimitação das superfícies geomórficas mapeadas no campo, o que indica o seu potencial de uso, na identificação e caracterização de áreas mais homogêneas.

Avaliação da qualidade dos óleos de fritura usados em restaurantes, lanchonetes e similares

A fritura é uma operação importante por ser um processo de preparação rápida de alimentos e por conferir aos produtos fritos características únicas de odor e sabor. Na temperatura de fritura o óleo interage com o ar, água e componentes dos alimentos que estão sendo fritos gerando compostos responsáveis por odores desagradáveis e degradações em óleos utilizados por longos períodos. Este trabalho foi conduzido com o objetivo de determinar os níveis de alteração dos óleos e gorduras utilizadas nos processos de fritura de restaurantes, lanchonetes, bares e pastelarias da cidade de São José do Rio Preto-SP. Os métodos analíticos aplicados para a avaliação da alteração em 60 amostras de óleos e gorduras incluíram a determinação de compostos polares totais (%), ácidos graxos livres (%, expressos em ácido oléico) e índice de peróxidos (meq/kg). Foram estabelecidos como limite de alteração 25% para compostos polares, 1% para ácidos graxos livres e 15meq/kg para índice de peróxidos. de acordo com os resultados obtidos, observou-se que das 60 amostras analisadas, 30% apresentaram valores de compostos polares superiores ao limite estabelecido para descartar os óleos e gorduras de fritura. Já, para ácidos graxos livres e índice de peróxidos, 18,3% e 8,3% das amostras, respectivamente, apresentaram valores acima do estabelecido para o descarte. Os elevados níveis de compostos polares totais encontrados (57,4%) em um número significativo de amostras demonstraram a necessidade de melhorar a qualidade dos óleos e gorduras de fritura neste setor de alimentação.

Fotopedologia, espectroscopia e sistema de informação geográfica na caracterização de solos desenvolvidos do Grupo Barreiras no Amapá

O presente trabalho utilizou ferramentas de sensoriamento remoto e sistema de informação geográfica, aliadas às informações espectrais do solo e quantitativas e qualitativas do relevo, para a caracterização e discriminação das classes de solos desenvolvidos do Grupo Barreiras na região do município de Porto Grande, Amapá. Após o mapeamento semidetalhado de solos, realizou-se a caracterização pontual das amostras dos perfis por meio de espectroscopia de visível e infravermelho (400-2500 nm), e a análise espacial das redes de drenagem e relevo a partir de fotos aéreas e imagens de radar. As informações quantitativas do relevo foram mais eficientes na caracterização e discriminação dos solos estudados do que as qualitativas, enquanto as informações espectrais permitiram caracterizar os solos em nível pontual. Métodos espaciais utilizando redes de drenagem e relevo e métodos espectrais utilizando amostras pontuais complementam-se na caracterização e discriminação de solos na paisagem.

Artrodese do carpo em gatos associada à hidroxiapatita

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

EFFECT OF WATER POTENTIAL ON GERMINATION OF SEEDS OF STYLOSANTHES-GUIANENSIS (AUBL) SW

Effect of water potential on germination of seeds of Slylosanthes guianensis (Aubl.) Sw. To evaluate the water potential effect on germination of S. guianensis two experiments were performed.The first one used osmotic pre-treatment in the imbibition phase and after this period (14 h) the seeds were germinated on filter paper moistened with distilled water. In the second experiment, besides the imbibition phase, seeds were kept in a range of water potentials during all the process. The potentials ranged from 0 to -18 bars, with 3 bars increments, induced by mannitol or by polyethylene glycol. Each treatment was replicated 3 times with 100 seeds per replication. The seeds pre-treated during imbibition had high germination percentage, the highest being the ones in polhyetylene glycol. In the second experiment the polyethylene glycol solutions reduced dramatically the germination percentage in relation to mannitol. From -12 bars on germination ceased in the polyethylene glycol treatments, while in mannitol solution there was 52,67% of germination, in the same water potential.

Evaluation of shear bond strength at the interface of two porcelains and pure titanium injected into the casting mold at three different temperatures

Statement of problem. Titanium has physical and mechanical properties, which have led to its increased use in dental prostheses despite casting difficulties due to high melting point and formation of oxide layers which affect the metal-ceramic bond strength.Purpose. This in vitro study evaluated the shear bond strength of the interface of 2 dental porcelains and pure titanium injected into a mold at 3 different temperatures.Material and methods. Using commercially pure (cp) titanium bars (Titanium, Grade I) melted at 1668degreesC and cast at mold temperatures of 430degreesC, 700degreesC or 900degreesC, 60 specimens were machined to 4 x 4 mm, with a base of 5 x 1 mm. The 4-mm surfaces were airborne-particle abraded with 100 mum aluminum oxide before applying and firing the bonding agent and evaluating the 2 porcelains (Triceram/Triline ti and Vita Titankeramik). Ten specimens were prepared for each temperature and porcelain combination Shear bond testing was performed in a universal testing machine, with a 500-kg load cell and crosshead speed of 0.5 mm/min. The specimens were loaded until failure. The interfaces of representative fractured specimens of each temperature were examined with a scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). Data for shear bond strength (MPa) were statistically analyzed by 2-way ANOVA and the Tukey test (alpha = .05).Results. The results showed significant differences for the metal/porcelain interaction effect (P = .0464). There were no significant differences for the 2 porcelains (P = .4250). The Tukey test showed a significant difference between the pair cp Ti 430degreesC Triceram and cp Ti 900degreesC Triceram, with respective mean values and SDs of 59.74 +/- 11.62 and 34.03 +/- 10.35 MPa.Conclusion. Triceram porcelain showed a bond strength decrease with an increase in the mold temperature for casting titanium. The highest bond strength for Vita porcelain and the best metal-ceramic interface observed with the SEM were found with the mold temperature of 700degreesC.

Coastal Marine Mapping as an Ecosystem Based Management - the case study of the Baixada Santista Region - São Paulo, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)