Influência da escala na análise morfométrica de microbacias hidrográficas

In order to verify the different scales in physical analysis of watersheds, the geomorphic quantitative analysis was done to distinguish homogeneous areas within this land unit. The variables studied were the dimensions, drainage pattern and relief characteristics. The study area is the watershed of the Corrego da Cachoeira, São Paulo State, Brazil. The cartographic scale 1: 50000 (IBGE) and 1: 10000 (IGC) were used to delineate the drainage network and study the morphometric characteristics. The watershed is characterized as an exoreic, fluvial drainage with consequent streams and drainage pattern. The values of the drainage density, frequency of rivers and the ratio of bifurcation are considered low, indicating the formation of the soil on permeable rock. The low values suggested a watershed with relatively mild relief. The detail of the cartography mapping analysed with field study data showed higher values of hydrological compartments and length of the drainage network, reflecting changes in the results obtained on the physical variables analysed.

Primary power distribution systems planning taking into account reliability, operation and expansion costs

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Comparação entre pericárdio bovino preservado em glicerina e malha de poliéster no reparo de falhas da parede abdominal em ratos

OBJETIVO: Comparar uma malha comercial de poliéster com o pericárdio bovino preservado em glicerina na reconstituição de defeitos da parede abdominal. MÉTODOS: Foram utilizados 30 ratos, divididos em dois grupos eqüitativos. Efetuou-se uma excisão retangular de 2,5 x 2 cm, incluindo toda a musculatura abdominal e peritônio. No grupo I a parede abdominal foi reparada com malha de poliéster e no grupo II com pericárdio bovino conservado em glicerina. Os animais foram sacrificados aos 15, 60 e 90 dias de pós-operatório, sendo o local cirúrgico avaliado macroscópica e histologicamente. RESULTADOS: Os animais do grupo I apresentaram aderências mais severas e em maior número quando comparados aos do grupo II; porém, sem comprometimento funcional. A análise histológica revelou incorporação dos tecidos aos implantes, com maior resposta fibroblástica nos animais do grupo I. CONCLUSÃO: A malha de poliéster oferece maior resistência estrutural e resposta fibroblástica mais intensa; contudo, promove grande quantidade de aderências às vísceras abdominais, quando comparada ao pericárdio bovino.

Influence of Cusp Inclination on Stress Distribution in Implant-Supported Prostheses. A Three-Dimensional Finite Element Analysis

Purpose: The aim of this study was to assess the influence of cusp inclination on stress distribution in implant-supported prostheses by 3D finite element method.Materials and Methods: Three-dimensional models were created to simulate a mandibular bone section with an implant (3.75 mm diameter x 10 mm length) and crown by means of a 3D scanner and 3D CAD software. A screw-retained single crown was simulated using three cusp inclinations (10 degrees, 20 degrees, 30 degrees). The 3D models (model 10d, model 20d, and model 30d) were transferred to the finite element program NeiNastran 9.0 to generate a mesh and perform the stress analysis. An oblique load of 200 N was applied on the internal vestibular face of the metal ceramic crown.Results: The results were visualized by means of von Mises stress maps. Maximum stress concentration was located at the point of application. The implant showed higher stress values in model 30d (160.68 MPa). Cortical bone showed higher stress values in model 10d (28.23 MPa).Conclusion: Stresses on the implant and implant/abutment interface increased with increasing cusp inclination, and stresses on the cortical bone decreased with increasing cusp inclination.

Stress Analysis in Platform-Switching Implants: A 3-Dimensional Finite Element Study

The aim of this study was to evaluate the influence of the platform-switching technique on stress distribution in implant, abutment, and pen-implant tissues, through a 3-dimensional finite element study. Three 3-dimensional mandibular models were fabricated using the Solid Works 2006 and InVesalius software. Each model was composed of a bone block with one implant 10 mm long and of different diameters (3.75 and 5.00 mm). The UCLA abutments also ranged in diameter from 5.00 mm to 4.1 mm. After obtaining the geometries, the models were transferred to the software FEMAP 10.0 for pre- and postprocessing of finite elements to generate the mesh, loading, and boundary conditions. A total load of 200 N was applied in axial (0 degrees), oblique (45 degrees), and lateral (90) directions. The models were solved by the software NeiNastran 9.0 and transferred to the software FEMAP 10.0 to obtain the results that were visualized through von Mises and maximum principal stress maps. Model A (implants with 3.75 mm/abutment with 4.1 mm) exhibited the highest area of stress concentration with all loadings (axial, oblique, and lateral) for the implant and the abutment. All models presented the stress areas at the abutment level and at the implant/abutment interface. Models B (implant with 5.0 mm/abutment with 5.0 mm) and C (implant with 5.0 mm/abutment with 4.1 mm) presented minor areas of stress concentration and similar distribution pattern. For the cortical bone, low stress concentration was observed in the pen-implant region for models B and C in comparison to model A. The trabecular bone exhibited low stress that was well distributed in models B and C. Model A presented the highest stress concentration. Model B exhibited better stress distribution. There was no significant difference between the large-diameter implants (models B and C).

Catch and selectivity parameters of the anastomid fish Schizodon nasutus using gillnets in the Jurumirim reservoir (São Paulo, Brazil)

Catch and selectivity parameters using gillnets were calculated for Schizodon nasutus in the Jurumirim reservoir on the Parana-panema River in southern Brazil. The simple gillnets used were made of monofilament nylon of 30 to 140 mm mesh size an of different heights. The relative abundance of the S. nasutus caught was analysed monthly and a positive relationship was found between catches per unit effort in number and biomass. The relative catches were more abundant for the nets of 40 and 50 mm, mesh size. Catches were characterized by clear temporal variations and a predominance of medium size fish throughout the study period. The selectivity curve of gillnets for S. nasutus in this ecosystem was obtained. The catch obtained was compared with the available catch for each mesh size, and the available catch for a certain length of fish was calculated starting from the theoretical selectivity curve. The 50 mm mesh size gillnet showed the best fit between real and available captures and was considered the most suitable, because a smaller mesh size resulted in a catch of predominantly immature specimens. It is expected that these results will contribute to improving management strategies for conservation of resources. Parameters such as the minimum catch length advisable or the mesh size permitted for a given species are indispensable for such decision-making.

Influence of Sources and Meteorology on Surface Concentrations of Gases and Aerosols in a Coastal Industrial Complex

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

INFLUENCE of THE EVAPORATOR POSITION IN STATIC DOMESTIC REFRIGERATORS

The temperature and velocity distributions of the air inside the cabinet of domestic refrigerators affect the quality of food products. If the consumer knows the location of warm and cold zones in the refrigerator, the products can be placed in the right zone. In addition, the knowledge of the thickness of thermal and hydrodynamic boundary layers near the evaporator and the other walls is also important. If the product is too close to the evaporator wall, freezing can occur, and if it is too close to warm walls, the products can be deteriorated. The aim of the present work is to develop a steady state computational fluid dynamics (CFD) model for domestic refrigerators working on natural convection regime. The Finite Volume Methodology is chosen as numerical procedure for discretizing the governing equations. The SIMPLE-Semi-Implicit Method for Pressure-Linked Equations algorithm applied to a staggered mesh was used for solving the pressure-velocity coupling problem. The Power-Law scheme is employed as interpolation function for the convective-diffusive terms, and the TDMA-Tri-Diagonal Matrix Algorithm is used to solve the systems of algebraic equations. The model is applied to a commercial static refrigerator, where the cabinet is considered an empty three-dimensional rectangular cavity with one drawer at the bottom of the cabinet, but without shelves. In order to analyze the velocity and temperature fields of the air flow inside the cabinet the evaporator temperature, Te, was varied from -20 degrees C to 0 degrees C, and nine different evaporator positions are evaluated for evaporator temperature of -15 degrees C. The cooling capacity of the evaporator for the steady state regime is also computed for each case. One can conclude that the vertical positioning of the evaporator inside the cabinet plays an important role on the temperature distribution inside the cabinet.

Análise temporal do uso e ocupação do solo na microbacia hidrográfica do córrego da Fazenda Glória, Município de Taquaritinga, SP

The role of environmental concern is important due to the disorganized land occupation and intense exploitation of natural resources which lead to the degradation and exhaustion of the environment. Remonte sensing techniques allow identifying, recognizing and mapping areas modifiers besides estimating the extension of alterations made by man. Thus, the objective of this study was to map land use and occupation in order to evaluate the development of the Gloria Farm Stream watershed in Taquaritinga, SP, Brazil, from 1983 to 2000. The drainage network and agricultural and natural vegetation areas were identified by stereoscopic analyses of 2000 aerial photographs and by data analyses of the field and cartographic documents. The results verified that sugarcane became predominat in 2000 and it is distributed in relatively large areas with detriment to citrus orchards and other crops. The presence of dams, which is not noted in 1983 data, and the increase of forest and natural vegetal fragment areas in the analyzed period was observed. Recovered areas dur to reforestation with native species were identified along the streams and springs of Jabuticabal Mountain Range.

Proposição de rotina morfológica para detecção de malha viária em imagens orbitais

The outdating of cartographic products affects planning. It is important to propose methods to help detect changes in surface. Thus, the combined use of remote sensing image and techniques of digital image processing has contributed significantly to minimize such outdating. Mathematical morphology is an image processing technique which describes quantitatively geometric structures presented in the image and provides tools such as edge detectors and morphological filters. Previous studies have shown that the technique has potential on the detection of significant features. Thus, this paper proposes a routine of morphological operators to detect a road network. The test area corresponds to an excerpt Quickbird image and has as a feature of interest an avenue of the city of Presidente Prudente, SP. In the processing, the main morphological operators used were threshad, areaopen, binary and erosion. To estimate the accuracy with which the linear features were detected, it was done the analysis of linear correlation between vectors of the features detected and the corresponding topographical map of the region. The results showed that the mathematical morphology can be used in cartography, aiming to use them in conventional cartographic updating processes.

Modifications induced by acetylacetone in properties of sol-gel derived Y3Al5O12:Tb3+ - I: Structural and morphological organizations

Acetylacetone has been used as a chemical modifier for the synthesis of undoped and Tb3+-doped Y3Al5O12 powders. A systematic investigation concerning its influence on the structural and morphological properties of amorphous and crystallized samples has been carried out. These properties have been comparatively studied by means of X-ray diffraction, infrared spectroscopy, SEM, XAS and SAXS. 27Al NMR and EPR experiments have been performed to complete the study. The combined results have evidenced that acetylacetone promotes organic groups departure during calcination, entailing a better structural organization at lower temperatures compared with unmodified powders. Structuration has been proven to occur at short-scale range until a 600°C heating treatment before being extended by coalescence at higher temperatures. Finally, the presence of acac ligands on the alkoxides leads to a monomer-cluster aggregation process, and thus to a more open network. © 2010 The Royal Society of Chemistry.

Análise bibliométrica da revista Scire: Um estudo de colaboração científica institucional

The aim of this research is to make a bibliometric analysis of the journal Scire: Representación y Organización del Conocimiento, edited in Spain, in order to evidence the most productive institutions and countries, as well as to build a cooperation network and calculate the density indicators, centrality degree and betweenness. The 292 articles of the period 1996 to 2010 were analyzed. It was found out that, of the institutions participating in the articles, 25 institutions have been clearly the most productive. Almost all of them are Spanish, except four Brazilian ones and three more from three different countries. The institutional network showed a low density, but several cooperative sub-networks were identified, which suggest the existence of an international dialogue among researchers on the discipline.

Neural networks models for wear patterns recognition of single-point dresser

Grinding is a workpiece finishing process for advanced products and surfaces. However, the constant friction between workpiece and grinding wheel causes the latter to lose its sharpness, thereby impairing the result of the grinding process. When this occurs, the dressing process is essential to sharpen the worn grains of the grinding wheel. The dressing conditions strongly influence the performance of the grinding operation; hence, monitoring them throughout the process can increase its efficiency. The purpose of this study was to classify the wear condition of a single-point dresser using intelligent systems whose inputs were obtained by digitally processing acoustic emission signals. Two multilayer perceptron (MLP) neural networks were compared for their classification ability, one using the root mean square (RMS) statistics and another the ratio of power (ROP) statistics as input. In this study, it was found that the harmonic content of the acoustic emission signal is influenced by the condition of the dresser, and that the condition of the tool under study can be classified by using the aforementioned statistics to feed a neural network. © IFAC.

Desenvolvimento de hardware e software para tratamento e visualização de dados de descargas atmosféricas aplicados à segurança da navegação hidroviária

Pós-graduação em Engenharia Elétrica - FEIS

Utilização de redes neurais recorrentes na caracterização de cargas não lineares em sistemas elétricos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)