Mullite whiskers grown from erbia-doped aluminum hydroxide-silica gel

Mullite whiskers and anisotropic grains that were derived from erbia-doped aluminum hydroxide-silica gel were studied. Firing 3.0-mol%-erbia-doped isostatically pressed pellets at 1600 degrees C for 1.0-8.0 h resulted in a high surface concentration of mullite whiskers. Their c-axes were aligned preferentially along the pellet surface; the maximum length was 50 mu m, and the maximum aspect ratio was 23. The pellet surface was fully covered by mullite whiskers, and small anisotropic grains with a low aspect ratio were observed in the bulk. The voids that were observed in the fracture surfaces were covered fully by mullite whiskers. The large number of voids resulted in an apparent density of 1.60 g/cm(3) in the sintered pellets. The molar ratio of alumina to silica in the whiskers was in the range of 1.30-1.45 tan average value of 1.31), regardless of whether the alumina/silica powder compositions were mixed in a 3:2 or 2:1 ratio.

Preparation of 9/65/35 PLZT thin films deposited by a dip-coating process

Crack-free polycrystalline PLZT (Pb,a)(Zr,Ti)O-3 thin films with the perovskite structure were prepared by dir-coating using the Pechinis process. Lead acetate, hydrated lanthanum carbonate, zirconium n-propoxide and titanium isopropoxide were used as raw materials. The viscosity of the solution was adjusted in the range of 20 to 56 cP and the films were deposited by a dip-coating process on silicon (100) as substrate. Solutions with ionic concentration of 0.1 and 0.2 M were used. Thin film deposition was accomplished by dipping the substrates in the solution with control of withdrawal speed from 5 to 20 mm/min. The thin films were thermally treated in two steps: at 300 degreesC amid 650 degreesC. The influence of withdrawal speed. viscosity, heating rate and ionic concentration on the morphology of PLZT thin film was discussed. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Effect of cobalt(II) oxide and manganese(IV) oxide on sintering of tin(IV) oxide

Additions of 0.5 to 2.0 mol% of CoO or MnO2 onto SnO, promote densification of this oxide up to 99% of theoretical density. The temperature of the maximum shrinkage rate (TM) and the relative density in the maximum densification rate (p*) during constant sintering heating rate depend on the dopant concentration. Thus, dopant concentration controls the densifying and nondensifying mechanisms during sintering. The densification of SnO2 witih addition of CoO or MnO, is explained in terms of the creation of oxygen vacancies.

Mechanism of phase formation in Pb(ZrxTi1-x)O3 synthesized by a partial oxalate method

The phase formation mechanism, as well as the morphotropic phase boundary, of lead zirconate titanate (PZT) processed by a partial oxalate method was investigated by simultaneous thermal analysis (TG-DTA) and by qualitative and quantitative X-ray diffraction (XRD). The results show that the ZrxTi1-xO2 (ZT) phase reacts with PbO forming the PZT phase without intermediate phases. XRD analysis showed the coexistence of rhombohedral and tetragonal phases for 0.47 ≤ x ≤ 0.55 with the phase boundary composition for x = 0.51. For low calcination temperatures, preferential formation of the PZT rhombohedral phase was observed. A model for phase formation of PZT by the partial oxalate method is proposed based on the existence of two interfaces of reaction (PbO-PZT and PZT-ZT) and diffusion of cations.

Particle growth during calcination of polycation oxides synthesized by the polymeric precursors method

The particle-growth kinetics of sodium niobate and zirconium titanate powders that were processed by the polymeric precursors method were studied. The growth kinetics that were studied for the particle, in the final stage of crystallization, showed that the growth process occurs in two different stages. For temperatures <800°C, the particle-growth mechanism is associated with surface diffusion, with an activation energy in the range of 40-80 KJ/mol. For temprratures >800°C, particle growth is controlled by densification of the nanometric particle cluster and by a neck-size-controlled particle-growth mechanism. The results suggest that this behavior was typical of the synthesis method, because two different polycation oxides presented the same behavior.

Repeatability and heritability of response to superovulation in Holstein cows

The objective of this study was to estimate the relative effects of genetic and phenotypic factors on the efficacy and efficiency of superovulation for Holstein-Friesian cows reared in Brazil. A database, established by the Associacao Brasileira de Criadores de Bovinos da Raca Holandesa, consisting of a total of 5387 superovulations of 2941 cows distributed over 473 herds and sired by 690 bulls was used for the analysis. The records were analyzed by MTDFREML (Multiple Trait Derivative-Free Restricted Maximum Likelihood), using a repeatability animal model. The fixed effects included in the model were contemporaneous group (veterinarian, herd, year and season of the superovulation); number of semen doses; cow age; and superovulation order. The estimated repeatability of the number of the transferable embryos was low (0.13), and the estimated heritability was 0.03. These results indicate that environmental factors play a critical role in the response of a cow to a superovulation treatment. There is little evidence that future responses to superovulation by individual females can be predicted by previous treatment(s) or that superovulation response is an heritable trait.

Direct amorphous-to-cubic perovskite phase transformation for lead titanate

The phase evolution of lead titanate processed by the polymeric precursor method was investigated by thermal analysis, X-ray diffraction, and high-resolution transmission electron microscopy. The results showed that the cubic perovskite PbTiO3 (PT) phase is formed from an inorganic amorphous precursor at a temperature of 444 °C. A gradual transition from cubic to tetragonal perovskite PT was observed with the increase of calcination time at this temperature. HRTEM results showed that the cubic PT particles have a size of around 5 nm. The identification of cubic PT as an intermediate phase supports the hypothesis that the chemical homogeneity was kept at the molecular level during the synthesis process, with no cation segregation.

Relações hídricas em cultivares de beterraba em diferentes níveis de salinidade do solo

The excess of salts in the soil can directly affect the development and yield of the plants, therefore, studies on water relationships of crops in such conditions are necessary to prevent or solve the problem. The study was conducted in a greenhouse at Universidade Estadual Paulista, Department of Agricultural Engineering, Botucatu, Brazil. The statistical design used was randomized blocks with four replications, consisting of five levels of soil salinity (1.0, 3.0, 6.0, 9.0, 12.0 dS m-1), two cultivars of sugar beet (Early Wonder and Itapuã) and two types of management of fertigation, totaling in all 80 plots. Measurements of water content of the leaves, diffuse resistance to water vapor, transpiration, leaf area and the water consumption of crop were determined. There was a decrease according to increasing salinity for the analysed physiological parameters in the Early Wonder variety while for the Itapuã variety a gradual increase was observed up to a salinity of 6 dS m-1. The water consumption by plants showed a reduction with increase of soil salinity for the two varieties.

Isolation and characterization of equine peripheral blood-derived multipotent mesenchymal stromal cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of the top-quark pole mass and strong coupling constant from the t(t)over-bar production cross section in pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Nondecalcified Histologic Study of Bone Response to Titanium Implants Topographically Modified by Laser With and Without Hydroxyapatite Coating

The purpose of this study was nondecalcified histologic analysis of titanium implants modified by laser with and without hydroxyapatite. Implants with three modified surfaces were inserted into rabbit tibias: group 1, machined surface; group 2, irradiated (laser); and group 3, irradiated and hydroxyapatite coated (biomimetic method). The mean surface roughness (Ra) scores of groups 2 and 3 were higher than that of group 1. Bone-implant contact measurements at 30 and 60 days for groups 2 and 3 were higher than for group 1. Bone area at 30 and 60 days for group 2 was higher than for groups 1 and 3. Titanium implants modified by laser with and without hydroxyapatite exhibit increased early osseointegration.

Structure of Hydrophobic Ambient-Pressure-Dried Aerogels Prepared by Sonohydrolysis of Tetraethoxysilane with Additions of N,N-Dimethylformamide

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Prevalence of obesity and relationship wit body mass index and symptoms of asthma in adolescents

To investigate the relationship between Body Mass Index (BMI) and asthma symptoms in adolescents between 13 and 14 years, to estimate the prevalence of obesity in this age group. This is a crosssectional study with a quantitative approach which was rated the Body Mass Index (BMI) and applied the Questionnaire International Study of asthma and Allergies in Childhood (ISAAC) phase III (asthma module) to determine the prevalence of asthma and related symptoms, as well as its severity in 85teenagers. According to the assessment of asthma in relation to BMI, it was found that there were significant findings, as well as in males and females. However, the association between BMI and asthma symptoms, there was a significant association to present as disturbed sleep and impaired speech. Conclusions: In this sample the prevalence of obesity was low, this fact may have contributed to the nonsignificant findings betweenasthma and BMI.