Poço de infiltração para controle de enchentes na fonte: avaliação das condições de operação e manutenção

This study investigated the following aspects regarding a soakaway, i.e. an infiltration well: i) entrance filter device; ii) permeability of the geotextile; and iii) emptying time. The 3.6 m³ infiltration well drains a roof area of 241.8 m². The entrance device is made up of layers of sand, gravel and geotextile set on a metal structure. The concrete rings that form the lateral walls were covered with geotextile, and bricks were laid between the soil and concrete rings. The infiltration well remained in operation during the entire testing period, and specific events were simulated to measure the emptying time. Permeability and fine particle tests were carried out after eight months of operation. Samples of geotextile taken from the bottom, the walls and the entrance device presented average permeability reductions of approximately 50.7%, 7.7% and 21.2%, respectively. The sand in the entrance device retained around 34.8% of fine particles and the gravel retained 0.13% in the same period. The infiltration rate was approximately 34.7 mm/h. The R2 coefficient for measured and calculated times was 0.97.

Produção e reprodução capitalista na indústria da reciclagem: uma análise do trabalho de catação de materiais recicláveis no interior paulista

Pós-graduação em Ciências Sociais - FFC

Estudo comparativo da textura superficial entre os materiais estéticos indiretos

The purpose of this study was to evaluate surface rugosity among indirect esthetic materials (Vita VMK 95, Solidex, Artglass, Targis). Ten samples of each material in the cilindric shape with dimension 6 x 6 mm were manufactured. The surface were submitted to finishing and polishing, according to manufacturer's recommendations. The samples were submitted to measuremenst, using the Hommel Tester T500 device. The average values of maxim surface rugosity among the materiais ín question, were 5, 73pm; 5, 15pm; 6, 83 j.Jm e 3, 72 j.Jm, respectively. Sample were also subjectted to variance analysis- ANOVA (5%), had detected significance. Concluded that the material Solidex did not present significant statistical differences among groups, while Targis presented significant statistical differences in relation to the Artglass and the ceramic Vita vmk95.

Verificação da dureza de gessos em função da compatibilidade com materiais de moldagem à base de borracha

Currently the most widespread material used in dies is gypsum that together with its simple technique has very satisfactory mechanical, chemical and physical properties. However, its compactibility with the impression materials can compromise the die surface quality. In our work, we studies the hardness of the two gypsum types: Type III (die stone) and type IV (improved die stone), as well as the influence of the contact with three types of impression materials: polymerized silicone for condensation (Xantopren), polysulfide (Permlastic) and polymerized silicone by addition (Provil). As comparison parameter gypsum was used in contact with a glass surface…(Complete abstract click electronic access below)

Influência de características físicas e química dos materiais de abutments de implantes em zircônia e titânio na adesão e viabilidade de células epiteliais gengivaiS OBA-9

Pós-graduação em Reabilitação Oral - FOAR

O design como mediador da arte-educação nos materiais didáticos de museus

Pós-graduação em Design - FAAC

Processamento sonoquímico de materiais mesoestruturados de óxido de zinco dopados com terras-raras

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Uma investigação sobre a utilização de materiais didáticos manipuláveis e a resolução de problemas no ensino e na aprendizagem de matemática dos anos iniciais do Ensino Fundamental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese de agentes hemostáticos coagulantes com base em materiais zeolíticos

Pós-graduação em Microbiologia - IBILCE

Síntese, caracterização estrutural, espectroscópica e análise do potencial fotocatalítico do aluminato de cobalto e potencial catalítico na preparação do biodiesel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação do comportamento de superfícies de fratura por fractais mistos em materiais de diferentes classes

Pós-graduação em Engenharia Mecânica - FEG

Detecção e localização de danos em materiais compósitos aplicado em aeronaves utilizando redes neurais artificiais

Pós-graduação em Engenharia Mecânica - FEIS

Avaliação da resistência adesiva entre a superfície de uma cerâmica aluminizada e um cimento resinoso

Pós-graduação em Odontologia Restauradora - ICT

Avaliação in vitro da resistência adesiva ao cisalhamento entre a dentina bovina, cimentos resinosos e materiais restauradores indiretos, tratados ou não com jato de óxido de alumínio, ácido fluorídrico e silano

The purpose of this study was to evaluate in vitro the shear bond strenght to bovine dentin, during 24h and 30 days with the following variables: resin cements Enforce and Panavia F; aesthetics restorative materials Art Glass, IPS Empress 2 and Targis, with surface treatment with microetching with aluminium oxide, fluoridric acid and silane. Two hundred eighty eight sound bovine teeth from 3 years old animals constituted the samples after inclusion on polyester resin box. lnstron model 430 Universal Testing Machine, a crosshead speed 0,5 mm/min and load cells of 500 Kg, was used for shear bond strenght testing (MPa). The results were statistically analysed by ANOVA The best result was obtained with /PS Empress 2, microetched with aluminium oxide, fluoridric acid and silane, cemented with Panavia F and stored in distilled water, 3f'C during 30 days

Síntese e propriedades fotoluminescentes do óxido de cério dopado com magnésio

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)