Influence of the gutta-percha taper and finger spreader on lateral consensation effectiveness

Introduction: Lateral condensation effectiveness may be influenced by the gutta-percha and finger spreader taper used during root canal obturation. Objective: To evaluate the penetration ability of finger spreader into simulated root canals prepared using MTwo rotary system and filled with different gutta-percha and finger spreader tapers. Material and methods: Resin blocks with curved root canals had the apical diameter enlarged up to #25.06 and distributed into groups (n = 6) according to the gutta-percha taper (#25.02, #25.04, and #25.06) and the finger spreader (#30 and #35 NiTi, and stainless steel B) used to perform cold lateral condensation. After applying a load of 1.5 Kg over the finger spreaders’ head, the distance between the finger spread tip and the apical limit of the root canal preparation were obtained. The data were submitted to Anova and Tukey-Krammer’s test, with 5% of significance. Results: The gutta-percha cones with 0.02 taper enabled higher finger spreader penetration when compared to 0.04 and 0.06 tapers (p < 0.05), which were similar between each other (p > 0.05), regardless of the type and diameter of the finger spreader used. When different finger spreaders were compared among themselves, stainless steel B showed higher penetration ability (p < 0.05). Conclusion: It was concluded that the stainless-steel finger spreaders showed superior penetration ability and gutta-percha with lower tapers enabled a more effective lateral condensation at the apical third.

Effect of finishing and polishing on color stability of a nanofilled resin immersed in different media

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influência do tratamento superficial 3IP na vida em fadiga dos aços ABNT 4340 e 15-5PH para aplicação aeronáutica

Pós-graduação em Engenharia Mecânica - FEG

Otimização do processo de soldagem por resistência elétrica em compósitos PEI/fibras contínuas para aplicações aeronáuticas

Pós-graduação em Engenharia Mecânica - FEG

Caracterização do aço inoxidável ASTM A743 CA6NM e do seu revestimento de WC-10Co-4Cr aspergido termicamente por HVOF

Pós-graduação em Engenharia Mecânica - FEG

The effect of thermal cycling on the shear bond strength of porcelain/Ti-6Al-4V interfaces

The aim of the study was to evaluate the effect of thermal cycling on the shear bond strength of the porcelain/Ti-6Al-4V interfaces prepared by two different processing routes and metallic surface conditions. Polished and SiO2 particle abraded Ti-6Al-4V alloy and Triceram bonder porcelain were used to produce the interfaces. Porcelain-to-metal specimens were processed by conventional furnace firing and hot pressing. Thermal cycling was performed in Fusayama's artificial saliva for 5000 cycles between 5 +/- 1 and 60 +/- 2 degrees C. After thermal cycling, shear bond tests were carried out by using a custom-made stainless steel apparatus. The results were analyzed using t-Student test and non-parametric Kruskal-Wallis test (p<0.01). Most of the polished-fired specimens were fractured during thermal cycling; thus, it was not possible to obtain the shear bond strength results for this group. Sandblasted-fired, polished-hot pressed, and sandblasted-hot pressed specimens presented the shear bond strength values of 76.2 +/- 15.9, 52.2 +/- 23.6, and 59.9 +/- 22.0 MPa, respectively. Statistical analysis indicated that thermal cycling affected the polished specimens processed by firing, whereas a significant difference was not observed on the other groups. (C) 2015 Elsevier Ltd. All rights reserved.

The effect of simvastatin treatment on bone repair of femoral fracture in animal model

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of furosemide treatment on the central and peripheral pressor responses to cholinergic and adrenergic agonists, angiotensin II, hypertonic solution and vasopressin

The present study was performed to investigate the effect of treatment with furosemide on the pressor response induced by intracerebroventricular (i.c.v.) injections of cholinergic (carbachol) and adrenergic (norepinephrine) agonists, angiotensin II (ANGII) and hypertonic saline (HS, 2 M NaCl). The changes induced by furosemide treatment on the pressor response to intravenous (i.v.) norepinephrine, ANGII and arginine vasopressin (AVP) were also studied. Rats with a stainless-steel cannula implanted into the lateral ventricle (LV) were used. Two injections of furosemide (30 mg/kg b.wt. each) were performed 12 and 1 h before the experiments. Treatment with furosemide reduced the pressor response induced by carbachol, norepinephrine and ANGII i.c.v., but no change was observed in the pressor response to i.c.v. 2 M NaCl. The pressor response to i.v. ANGII and norepinephrine, but not AVP, was also reduced after treatment with furosemide. These results show that the treatment with furosemide impairs the pressor responses induced by central or peripheral administration of adrenergic agonist or ANGII, as well as those induced by central cholinergic activation. The results suggest that the treatment with furosemide impairs central and peripheral pressor responses mediated by sympathetic activation and ANGII, but not those produced by AVP. © 1992.

Importance of the central nucleus of the amygdala on sodium intake caused by deactivation of lateral parabrachial nucleus

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of essential oils of Syzygium aromaticum and Cinnamomum zeylanicum and their major components on biofilm production in Staphylococcus aureus strains isolated from milk of cows with mastitis

Bovine mastitis is an inflammation of the mammary glands of cows and causes significant economic losses in dairy cattle. Staphylococcus aureus is one of the microorganisms most commonly isolated. Novel agents are required in agricultural industries to prevent the development of mastitis. The production of biofilm by Staph. aureus facilitates the adhesion of bacteria to solid surfaces and contributes to the transmission and maintenance of these bacteria. The effect of the essential oils of Syzygium aromaticum (clove; EOSA) and Cinnamomum zeylanicum (cinnamon; EOCZ) and their major components, eugenol and cinnamaldehyde, on Staph. aureus biofilm formation on different surfaces was investigated. The results showed a significant inhibition of biofilm production by EOSA on polystyrene and stainless steel surfaces (69.4 and 63.6%, respectively). However, its major component, eugenol, was less effective on polystyrene and stainless steel (52.8 and 19.6%, respectively). Both EOCZ and its major component, cinnamaldehyde, significantly reduced biofilm formation on polystyrene (74.7 and 69.6%, respectively) and on stainless steel surfaces (45.3 and 44.9%, respectively). These findings suggest that EOSA, EOCZ, and cinnamaldehyde may be considered for applications such as sanitization in the food industry.

Hydrogen peroxide centrally attenuates hyperosmolarity-induced thirst and natriuresis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da resistência à tração de cápsulas e troqueis metálicos cimentados, em função de alívio e retenção para o cimento

Pós-graduação em Odontologia Restauradora - ICT

Role of the medial septal area on the cardiovascular, fluid and electrolytic responses to angiotensin II and cholinergic activation into the subfornical organ in rats

In the present study we investigated the effect of electrolytic lesion of the medial septal area (MSA) on the pressor and dipsogenic response to cholinergic activation and angiotensin II (ANGII) injection into the subfornical organ (SFO) in rats. In addition the effect of MSA lesion on the natriuresis, kaliuresis and diuresis after cholinergic activation of the SFO was also investigated. Sham- and MSA-lesioned rats with a stainless steel cannula implanted into the SFO was used. The injection of ANGII (12 ng) into the SFO in sham rats produced pressor (24 ± 2 mmHg) and dipsogenic (9.6 ± 1.1 ml/h) responses. MSA lesion, both acute (2-6 days) and chronic (15-19 days), reduced the pressor (14 ± 2 mmHg) and dipsogenic (2.7 ± 1 ml/h) responses to ANGII into SFO. The injection of the cholinergic agonist carbachol (2 nmol) into the SFO in sham rats produced pressor (48 ± 4 mmHg), dipsogenic (10 ± 1.2 ml/h), natriuretic (457 ± 58 μEq/2 h) and kaliuretic (249 ± 16 μEq/2 h) responses. Acute, but not chronic MSA lesion reduced the pressor (27 ± 3 mmHg), natriuretic (198 ± 55 μEq/2 h) and kaliuretic (128 ± 16 μEq/2 h) responses to carbachol into SFO. No change in the dipsogenic response to carbachol into the SFO was observed in MSA-lesioned rats. Antidiuresis after carbachol was observed only in MSA-lesioned rats. The present results show that the MSA plays a role on the pressor, natriuretic and kaliuretic responses to cholinergic activation of the SFO in rats and on the pressor and dipsogenic responses to ANGII into the same area. In addition, they provide circumstancial evidence for separate circuits subserving the dipsogenic response to central cholinergic and angiotensinergic activation. A facilited diuresis after MSA lesion is also suggested.

Análise de materiais para sistemas de fechamento ósseo através da caracterização superficial e comportamento mecânico

Pós-graduação em Engenharia Mecânica - FEB

Ultra-precision face grinding with constant pressure, lapping kinematics, and SiC grinding wheels dressed with overlap factor

Several machining processes have been created and improved in order to achieve the best results ever accomplished in hard and difficult to machine materials. Some of these abrasive manufacturing processes emerging on the science frontier can be defined as ultra-precision grinding. For finishing flat surfaces, researchers have been putting together the main advantages of traditional abrasive processes such as face grinding with constant pressure, fixed abrasives for two-body removal mechanism, total contact of the part with the tool, and lapping kinematics as well as some specific operations to keep grinding wheel sharpness and form. In the present work, both U d-lap grinding process and its machine tool were studied aiming nanometric finishing on flat metallic surfaces. Such hypothesis was investigated on AISI 420 stainless steel workpieces U d-lap ground with different values of overlap factor on dressing (Ud=1, 3, and 5) and grit sizes of conventional grinding wheels (silicon carbide (SiC)=#800, #600, and #300) applying a new machine tool especially designed and built for such finishing. The best results, obtained after 10 min of machining, were average surface roughness (Ra) of 1.92 nm, 1.19-μm flatness deviation of 25.4-mm-diameter workpieces, and mirrored surface finishing. Given the surface quality achieved, the U d-lap grinding process can be included among the ultra-precision abrasive processes and, depending on the application, the chaining steps of grinding, lapping, and polishing can be replaced by the proposed abrasive process.