Compilação para arquitetura reconfigurável

Pós-graduação em Ciência da Computação - IBILCE

SW-V: modelo de streaming de software baseado em técnicas de virtualização e transporte peer-to-peer

Pós-graduação em Ciência da Computação - IBILCE

Analise de desempenho de um sistema híbrido de geração de energia solar-eólico-diesel considerando variações probabilísticas da carga e dos recursos renováveis

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Inversores integrados monofásicos e trifásicos para aplicações fotovoltaicas: técnicas para obtenção de mppt, detecção e proteção de ilhamento, sincronização e paralelismo com a rede de distribuição de energia elétrica

Pós-graduação em Engenharia Elétrica - FEIS

Aplicação de computação evolucionária na mineração de dados físico-químicos da água e do solo

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Integration of wireless sensor networks to the internet of things using a 6LoWPAN Gateway

The Internet of Things is a new paradigm where smart embedded devices and systems are connected to the Internet. In this context, Wireless Sensor Networks (WSN) are becoming an important alternative for sensing and actuating critical applications like industrial automation, remote patient monitoring and domotics. The IEEE 802.15.4 protocol has been adopted as a standard for WSN and the 6LoWPAN protocol has been proposed to overcome the challenges of integrating WSN and Internet protocols. In this paper, the mechanisms of header compression and fragmentation of IPv6 datagrams proposed in the 6LoWPAN standard were evaluated through field experiments using a gateway prototype and IEEE 802.15.4 nodes.

Abordagem icônica para modelagem e simulação de ambientes de computação em nuvem ?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Increasing Moodle Resources Through Cloud Computing

The increase of higher education offer is a basic need of developed and emerging countries. It requires increasing and ongoing investments. The offer of higher education, by means of Distance Learning, based on the Internet, is one of the most efficient manners for the massification of this offer, as it allows ample coverage and lower costs. In this scenario, we highlight Moodle, an open and low-cost environment for Distance Learning. Its utilization may be amplified through the adoption of an emerging Information and Communication Technology (ICT), Cloud Computing, which allows the virtualization of Moodle sites, cutting costs, facilitating management and increasing its service capacity. This article diffuses a public tool, opened and free, for automatic conversion of Moodle sites, such that these may be hosted on Azure: the Cloud Computing environment of Microsoft.

THE SERVICE LIFE of IMPLANT-RETAINED OVERDENTURE ATTACHMENT SYSTEMS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A case study of concurrent engineering application on the development of parts for the white goods industry in Brazil

This classical way to manage product development processes for massive production seems to be changing: high pressure for cost reduction, higher quality standards, markets reaching for innovation lead to the necessity of new tools for development control. Into this, and learning from the automotive and aerospace industries factories from other segments are starting to understand and apply manufacturing and assembly oriented projects to ease the task of generate goods and from this obtain at least a part of the expected results. This paper is intended to demonstrate the applicability of the concepts of Concurrent Engineering and DFM/DFA (Design for Manufacturing and Assembly) in the development of products and parts for the White Goods industry in Brazil (major appliances as refrigerators, cookers and washing machines), showing one case concerning the development and releasing of a component. Finally is demonstrated in a short term how was reached a solution that could provide cost savings and reduction on the time to delivery using those techniques.

Single stage converters for low power stand-alone and grid-connected PV systems

This work presents the evaluation of different power electronic integrated converters suitable for photovoltaic applications, in order to reduce complexity and improve reliability. The rated voltages available in Photovoltaic (PV) modules have usually low values for applications such as regulated output voltages in stand-alone or grid-connected configurations. In these cases, a boost stage or a transformer will be necessary. Transformers have low efficiencies, heavy weights and have been used only when galvanic isolation is mandatory. Furthermore, high-frequency transformers increase the converter complexity. Therefore, the most usual topologies use a boost stage and one inverter stage cascaded. However, the complexity, size, weight, cost and lifetime might be improved considering the integration of both stages. In this context, some integrated converters are analyzed and compared in this paper in order to support future evaluations and trends for low power single-phase inverters for PV systems. Power decoupling, MPPT and Tri-State modulations are also considered. Finally, simulation and experimental results are presented and compared for the analyzed topologies. © 2011 IEEE.

Improving the grid operation and reliability cost of distribution systems with dispersed generation

In this work, a mathematical model to analyze the impact of the installation and operation of dispersed generation units in power distribution systems is proposed. The main focus is to determine the trade-off between the reliability and operational costs of distribution networks when the operation of isolated areas is allowed. In order to increase the system operator revenue, an optimal power flow makes use of the different energy prices offered by the dispersed generation connected to the grid. Simultaneously, the type and location of the protective devices initially installed on the protection system are reconfigured in order to minimize the interruption and expenditure of adjusting the protection system to conditions imposed by the operation of dispersed units. The interruption cost regards the unsupplied energy to customers in secure systems but affected by the normal tripping of protective devices. Therefore, the tripping of fuses, reclosers, and overcurrent relays aims to protect the system against both temporary and permanent fault types. Additionally, in order to reduce the average duration of the system interruption experienced by customers, the isolated operation of dispersed generation is allowed by installing directional overcurrent relays with synchronized reclose capabilities. A 135-bus real distribution system is used in order to show the advantages of using the mathematical model proposed. © 1969-2012 IEEE.

Determining spatial resolution in spatial load forecasting using a grid-based model

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

An approach to mitigate denial of service attacks in ieee 802.11 networks

Wireless networks are widely deployed and have many uses, for example in critical embedded systems. The applications of this kind of network meets the common needs of most embedded systems and addressing the particularities of each scenario, such as limitations of computing resources and energy supply. Problems such as denial of service attacks are common place and cause great inconvenience. Thus, this study presents simulations of denial of service attacks on 802.11 wireless networks using the network simulator OMNeT++. Furthermore, we present an approach to mitigate such attack, obtaining significant results for improving wireless networks.