Colorimetric determination of ammonia in air using a hanging drop

A simple and sensitive method for determining atmospheric ammonia (NH3), using a hanging drop, is described. A colorimetric sensor is composed of two optical fibers and the source of monochromatic light implemented was a red light emitting diode (LED) (635 nm). Preliminary experiments were carried out in order to optimize the geometry of the sensor. These tests showed that the best signal absorbance was obtained using a 22 muL deionized water drop for sampling the gas and as addition of 4 muL of each of the reactants to form the blue dye (indophenol). Some important analytical parameters were also studied, including sampling time and flow rate. The analytical curve was constructed with a concentration range of 3-20 ppbv of gaseous NH3 standard. The detection limit reached was of ca 0.5 ppbv. It was observed that formaldehyde and diethylamine did not interfere. However, studies showed that hydrogen sulfide caused a negative interference of 20%, when present in the atmosphere in a concentration equal to that of NE3. The method considered here was shown to be easy to apply, making it possible to make a determination every 17 min.

Construction and performance of a drop cell for the nephelometric determination of sulfur dioxide

A nephelometric technique based on a liquid drop is described for the measurement of atmospheric sulfur dioxide. A 40-mul drop of barium chloride and hydrogen peroxide solution is suspended in a flowing-air sampling stream. The sulfur (IV) collected is oxidized to sulfur (VI) and finally precipitated as barium sulfate. Nephelometric detection of drop is achieved by an appropriate arrangement consisting of an optical fiber contacting the drop and a photodiode placed at 90degrees relative to the fiber. The design and characteristics of this drop-based gas sensor system are described. The analytical response, as photocurrent, is proportional to the product of the sampling period and the sulfur dioxide concentration. The detection limit is ca. 1.1 mg m(-3) for a 10-min sampling time. The present technique is fairly rapid and simple, uses a small amount of reagent and is set up with low-cost equipment, making this system economically viable. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Measurement of atmospheric formaldehyde using a drop collector and in-situ colorimetry

A sensitive and affordable approach is described for the in-situ measurement of ambient formaldehyde. Air is sampled around a 100 microliter aqueous drop containing 3-methyl-2-benzothiazoline hydrazone. After a desired period of sampling (typ. 5 min) and a waiting period of 10 min for the reaction to be completed, a second reagent (FeCl3) is added to the drop by means of a conjoined conduit. A blue product is formed and is read after an additional 10 min of reaction by a fiber-optic/light emitting diode based photodetector. A fresh drop is then formed and the process begins anew. As demonstrated here, the limit of detection is similar to 6.25 mu g m(-3) HCHO but can be significantly improved by using longer sampling times and a sampling rate higher than 100 mi min(-1) used in most of this work. This is the first example of a chromogenic drop sensor that utilizes sequential reagent addition.

Effect of apparent viscosity on the pressure drop during fluidized bed drying of soursop pulp

Pressure drop and minimum fluidization velocity were experimentally studied in a vibro-fluidized bed of inert particles subjected to different vibration intensities during drying of soursop pulp. Maltodextrin was added to the pulp in order to prevent stickiness between particles and the consequent bed collapse. Pulps were initially concentrated, resulting in pastes with different soluble solids content, and a constant fraction of maltodextrin was guaranteed in the final pulp samples. The pulp theological behavior as affected by temperature and total soluble solids content, including maltodextrin, was evaluated and the effect of pulp apparent viscosity on pressure drop and minimum vibro-fluidization velocity were investigated. Two types of inert particles -3.6 mm glass beads and 3 mm Teflon cylinders (length and diameter) - were tested and, due to lower pressure drop presented by Teflon cylinders during operation of the dry vibro-fluidized bed, these particles were adopted for pulp drying process. Increasing pulp apparent viscosity caused a considerable increase in the vibro-fluidized bed pressure drop during pulp drying and, as a consequence resulted in a larger value of minimum vibro-fluidization velocity. on the other hand, the negative effect of increasing apparent viscosity could be attenuated by increasing the fluidized bed vibration intensity, which could prevent stickiness between particles. (c) 2006 Elsevier B.V. All rights reserved.

Activity of benomyl for control of postbloom fruit drop of citrus caused by Colletotrichum acutatum

Postbloom fruit drop (PFD) of citrus caused by Colletotrichum acutatum produces orange-brown lesions on petals and induces the abscission of young fruitlets and the retention of the calyces. Despite the fact that C. acutatum is not highly sensitive to benomyl in culture, this fungicide provides good control of the disease under field conditions. This study was undertaken to determine the effect of benomyl on various stages of disease development to understand the basis for its effectiveness in the field. We found that benomyl at 1.0 μg/ml reduced colony area of C. acutatum by about 75% and completely inhibited growth of C. gloeosporioides. Benomyl did not prevent conidial germination even at 100 μg/ml, but reduced germ tube elongation at 10 and 100 μg/ml. When benomyl was applied to flower clusters on screen-house-grown plants before inoculation, disease severity was greatly reduced. Applications at 24 and 48 h, but not at 72 h, after inoculation reduced PFD severity. Application of benomyl to symptomatic petals not bearing conidia did not prevent or reduce production of inoculum. Application to petals bearing conidia reduced viability of these fungal propagules by only about 50%. The viability of appressoria on mature leaves was not affected by benomyl application. Even when appressoria on mature leaves were stimulated to germinate by treatment with flower extracts, subsequent application of benomyl did not reduce propagule numbers below original levels. Benomyl appears to act by preventing infection and early development of the fungus in petals. However, once symptoms have developed, this fungicide has only minimal effects on further disease development and spread.

Evaluation of systems for timing of fungicide sprays for control of postbloom fruit drop of citrus in Brazil

Postbloom fruit drop (PFD) of citrus, caused by Colletotrichum acutatum, infects petals of citrus flowers and produces orange-brown lesions that induce the abscission of young fruitlets and the retention of calyces. Proper timing of fungicide applications is essential for good disease control. Different systems for timing of fungicide applications for control of PFD in a major citrus-growing region in southern São Paulo state in Brazil were evaluated from 1999 to 2002. The following programs were compared to an unsprayed control using counts of diseased flowers, persistent calyces, or fruit: (i) a phenology-based program currently recommended in Brazil with one application at early and another at peak bloom; (ii) the Florida PFD model; (iii) the postbloom fruit drop-fungicide application decision system (PFD-FAD), a new computer-assisted decision method; and (iv) grower's choice. In 1999, no disease developed, sprays applied with the phenology-based program had no effect, and the Florida PFD model saved two sprays compared with the phenology-based program. In 2000, PFD was moderate and the phenology-based and growers' choice treatments had a significantly lower number of persistent calyces and higher fruit numbers than the control, but no differences were found between those treatments and the PFD model. In 2001, PFD was severe with considerable yield loss. The PFD model, the phenology-based program, and the grower's choice reduced flower blight and the number of persistent calyces, and improved fruit yields with two to three applications, but the PFD-FAD achieved comparable yields with only one spray. In 2002, the disease was mild, with no yield loss, and the Florida PFD model and the PFD-FAD saved one spray compared with the other systems. The PFD model and the PFD-FAD were equally effective for timing fungicide applications to control PFD in Brazil. Scouting of trees is simpler with PFD-FAD; therefore, this system is recommended and should eliminate unnecessary sprays and reduce costs for growers.

Determination of the force systems produced by different configurations of tear drop orthodontic loops

Objective: To determine the mechanical characteristics of teardrop loop with and without helix fabricated using different metal alloy compositions (stainless steel and beta-titanium), submitted to different intensities of bends preactivation (0° and 40°), and with different cross-sectional dimension of the wire used to build these loops (0.017 x 0.025-in and 0.019 x 0.025-in). Methods: Eighty loops used to close spaces were submitted to mechanical tests. The magnitudes of horizontal force, the moment/force ratio, and the load/deflection ratio produced by the specimens were quantified. Loops were submitted to a total activation of 5.0 mm and the values were registered for each 1.0 mm of activation. For statistic data analysis, a analysis of variance was performed and a Tukey's Multiple Comparison test was used as supplement, considering a 5% level of significance. Results: In general, teardrop loops with helix produced lower magnitudes of horizontal force and load/deflection ratio, and higher moment/force ratio than teardrop loops without helix. Among all analyzed variables, metal alloy composition presented greater influence in the horizontal force and in the load/deflection ratio. The moment/force ratio showed to be more influenced by the preactivation of loops for space closure. © 2013 Dental Press Journal of Orthodontics.

INFLUENCE OF NOZZLE TYPE AND SPRAY RATES ON CORN AND WEED PLANTS DROP DEPOSITIONS

The objective of this study was to evaluate different nozzles and spray rates on drop deposition in corn (Zea mays), Euphorbia heterophylla and Brachiaria plantaginea, both weeds located at and between crop rows. The experimental design established was complete random blocks with treatments arranged at 2 x 2 factorial scheme (2 nozzles types: DG11002VS flat flan and medium droplets, TXVK08 cone and very fine droplets; and 2 rates: 100 and 200 L ha(-1)) with four replications. The spray applications occurred at 13 days after corn germination (3-5 expanded leaves), when E. heterophylla and B. plantaginea plants had 2-4 and 2-3 leaves, respectively. Solution of Brilliant Blue (FD&C-1) dye at 3,000 ppm was used as spray tracer. It was concluded that the greatest average deposits in corn plants was provided by TXVK08, independently of the spray rates used. The most uniform deposits occurred when the spray rates of 200 L ha(-1) was used. Spray deposits were most uniform in B. plantaginea compared to E. heterophylla when both weds were located at crop row, independently of nozzle or spray rates. However, the DG 11002VS spray nozzle provided the most uniform drop deposition on B. plantaginea located between the rows, while the most efficient deposition over E. heterophylla located between rows was TXVK08.

Utilização do cavaco de madeira como combustível alternativo para a produção de vapor de água em uma caldeira aquatubular com grelha fixa do tipo PIN HOLE

The steady increase in the price of oil and its derivatives, carbon credits, the concern with the environment combined with the precipitation of rain water and lack of water resources that Brazil has suffered in 2014 caused a migration of participation sources of energy in the Brazilian energy matrix. The hydropower sector suffered big drop at 2013 and is suffering so far, contributing thus to the generation and cogeneration of thermal energy using renewable energy sources such as: sugarcane bagasse, wood chips, rice husks, among others. The selling price of the electricity market reached the level of R$ 807, 00 MWh in January 2014 (Source: ANEEL), heating the Brazilian thermoelectric sector. Although thermoelectric use in bulk water as vaporizing fluid to produce electricity and use in various processes, water reuse plans have become an important factor in these industries. The increased use of biomass has been the bagasse which is allied to the sugarcane sector, strong market in Brazil, and consists basically use the rest of sugar cane, sugarcane industries that would play out. The sugar and ethanol industry is very unstable and only lasts for 6-8 months a year, and the remaining time in the period known as between crop that corresponds to the planting and harvesting of sugarcane and then enter the period of vintage which is the constant cane harvesting and crushing it. This instability of the market and the thermoelectric idle period leads the thermoelectric industries to seek other sources of renewable energy, such as wood chips (pine, Eucalyptus, Orange), rice husk, sorghum among others, to not be dependent on alcohol sector. The present work aims to study the use of wood chips as an alternative biomass for burning a fuel that essentially uses bagasse, the thermoelectric in question consists of two boilers that produce together 350 t / h ... (Complete Abstract click electronic access below)

Capacitive DNA detection driven by electronic charge fluctuations in a graphene nanopore

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)