Force and displacement transmissibility of a nonlinear isolator with high-static-low-dynamic-stiffness

Engineers often face the challenge of reducing the level of vibrations experienced by a given payload or those transmitted to the support structure to which a vibrating source is attached. In order to increase the range over which vibrations are isolated, soft mounts are often used in practice. The drawback of this approach is the static displacement may be too large for reasons of available space for example. Ideally, a vibration isolator should have a high-static stiffness, to withstand static loads without too large a displacement, and at the same time, a low dynamic stiffness so that the natural frequency of the system is as low as possible which will result in an increased isolation region. These two effects are mutually exclusive in linear isolators but can be overcome if properly configured nonlinear isolators are used. This paper is concerned with the characterisation of such a nonlinear isolator comprising three springs, two of which are configured to reduce the dynamic stiffness of the isolator. The dynamic behaviour of the isolator supporting a lumped mass is investigated using force and displacement transmissibility, which are derived by modelling the dynamic system as a single-degree-of-freedom system. This results in the system dynamics being approximately described by the Duffing equation. For a linear isolator, the dynamics of the system are the same regardless if the source of the excitation is a harmonic force acting on the payload (force transmissibility) or a harmonic motion of the base (displacement transmissibility) on which the payload is mounted. In this paper these two expressions are compared for the nonlinear isolator and it is shown that they differ. A particular feature of the displacement transmissibility is that the response is unbounded at the nonlinear resonance frequency unless the damping in the isolator is greater than some threshold value, which is not the case for force transmissibility. An explanation for this is offered in the paper. (C) 2011 Elsevier Ltd. All rights reserved.

Novel active and passive anti-vibration mountings

This paper investigates a novel design approach for a vibration isolator for use in space structures. The approach used can particularly be applicable for aerospace structures that support high precision instrumentation such as satellite payloads. The isolator is a space-frame structure that is folded in on itself to act as a mechanical filter over a defined frequency range. The absence of viscoelastic elements in such a mounting makes the design suitable for use in a vacuum and in high temperature or harsh environments with no risk of drift in alignment of the structure. The design uses a genetic algorithm based geometric optimisation routine to maximise passive vibration isolation, and this is hybridised with a geometric feasibility search. To complement the passive isolation system, an active system is incorporated in the design to add damping. Experimental work to validate the feasibility of the approach is also presented, with the active/passive structure achieving transmissibility of about 19 dB over a range of 1-250 Hz. It is shown here that the use of these novel anti-vibration mountings has no or little consequent weight and cost penalties whilst maintaining their effectiveness with the vibration levels. The approach should pave the way for the design of anti-vibration mountings that can be used between most pieces of equipment and their supporting structure. Crown Copyright (C) 2011 Published by Elsevier Ltd. All rights reserved.

Effect of Passive Fit Absence in the Prosthesis/Implant/Retaining Screw System: A Two-Dimensional Finite Element Analysis

The misfit between prostheses and implants is a clinical reality, but the level that can be accepted without causing mechanical or biologic problem is not well defined. This study investigates the effect of different levels of unilateral angular misfit prostheses in the prosthesis/implant/retaining screw system and in the surrounding bone using finite element analysis. Four models of a two-dimensional finite element were constructed: group I (control), prosthesis that fit the implant; groups 2 to 4, prostheses with unilateral angular misfit of 50, 100, and 200 mu m, respectively. A load of 133 N was applied with a 30-degree angulation and off-axis at 2 mm from the long axis of the implant at the opposite direction of misfit on the models. Taking into account the increase of the angular misfit, the stress maps showed a gradual increase of prosthesis stress and uniform stress in the implant and trabecular bone. Concerning the displacement, an inclination of the system due to loading and misfit was observed. The decrease of the unilateral contact between prosthesis and implant leads to the displacement of the entire system, and distribution and magnitude alterations of the stress also occurred.

Changes in the stiffness of demineralized dentin following application of tooth whitening agents

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência da suspensão na segurança e no conforto de um pulverizador autopropelido

Para avaliar o comportamento da suspensão do pulverizador autopropelido, foram desenvolvidos modelos físicos e matemáticos em função da excitação ocasionada pelas irregularidades do solo. Neste trabalho, estas irregularidades são representadas por obstáculos de uma pista normalizada segundo a norma ISO 5008. As equações do movimento são obtidas a partir dos modelos matemáticos de meio veículo. As simulações numéricas são executadas nos softwares Matlab® e Simulink®. A partir da entrada conhecida, podem-se determinar as características dos elementos da suspensão para obter níveis desejáveis de conforto e segurança. Foram analisadas quatro diferentes configurações do sistema, variando-se a relação de rigidez a partir de um modelo considerado padrão. Constatou-se que o aumento da relação de rigidez resulta na redução da aceleração vertical e no aumento do curso da suspensão, melhorando o conforto e diminuindo a segurança.

Development of a sensitive passive sampler using indigotrisulfonate for the determination of tropospheric ozone

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Improving the passive doppler geolocation system through extension of the data reception network

O objetivo deste trabalho e apresentar uma investigação preliminar da precisão nos resultados do sistema de localização geográfica de transmissores desenvolvido utilizando o software da rede brasileira de coleta de dados. Um conjunto de medidas de desvio Doppler de uma única passagem do satélite, considerando uma Plataforma de Coleta de Dados (PCD) e uma rede de estações de recepção terrestrês, e denominado uma rede de recepção de dados. Assim, a rede brasileira de coleta de dados com o uso de múltiplas estações de recepção permitira o incremento na quantidade de dados coletados com consequente melhora na precisão e na confiabilidade das localizações fornecidas. Consequentemente uma maior quantidade de localizações válidas e mais precisas. Os resultados e análises foram obtidos sob duas condições: na primeira foi considerada uma condição prática com dados reais e dados ideais simulados, para comparar os resultados considerando a mesma passagem do satélite, transmissor e duas estações de recepção conhecidas; na segunda foram consideradas as condições ideais simuladas a partir de medidas de um transmissor fixo, três estações de recepção e dois satélites. Os resultados utilizando a rede de recepção de dados foram bastante satisfatórios. O estudo realizado mostrou a importãncia da instalação de novas estações de recepção terrenas distribuídas no territorio nacional, para um aumento na quantidade de medidas e consequentemente uma maior quantidade de localizações válidas e mais precisas.

Endocrine profiles and ovulation rate of cows superovulated with FSH following passive immunization against steroid free-bovine follicular fluid

Dez vacas multíparas, secas, foram distribuídas aleatoriamente em dois grupos de cinco animais cada. Nos dias 8 a 12 do diestro, o primeiro grupo recebeu 100 ml de anti-soro contra líquido folicular livre de esteróides (anti-LFb) produzido em ovelhas ovariectomizadas. O segundo grupo (controle) recebeu 100 ml de soro de ovelhas não-imunizadas. Seis horas após a aplicação, os dois grupos foram superovulados com FSH (18 NIH-FSH-S1 unidades) e LH (0,29 NIH-LH-S1 unidades) administrados em quantidades decrescentes durante quatro dias. Na manhã do terceiro dia, foi administrada uma dose luteolítica de cloprostenol. Duas inseminações foram realizadas 48 e 60 horas após. Os embriões foram recuperados pelo método cervical 7 dias após a primeira inseminação. Amostras de sangue foram coletadas durante todo o período experimental para determinar, por radioimunoensaio, as concentrações plasmáticas de FSH, LH e progesterona. Todas as vacas do grupo imunizado e 3 do grupo controle apresentaram mais de 2 CL. Não existiu diferença significativa (P>0,05) na taxa de ovulação entre os grupos imunizado e controle (14,4 e 9,9, respectivamente). O número de embriões recuperado não foi significativamente diferente (P>0,05) entre os grupos, embora o grupo imunizado tenha apresentado maior número de embriões transferíveis (3,4 ± 1,0 versus 0,8 ± 0,4, P<0,05). As concentrações de gonadotrofinas plasmáticas não foram correlacionadas com a taxa de ovulação ou com o número de embriões recuperados. As concentrações de progesterona plasmática foram positivamente correlacionadas (r = 0,88, P<0,01) com a taxa de ovulação. Os resultados sugerem que o anti-LFb, aplicado antes da superovulação, não reduz a variabilidade da resposta ovariana.

Effect of the passive recovery period on the lactate minimum speed in sprinters and endurance runners

The objective of this study was to verify the effect of the passive recovery time following a supramaximal sprint exercise and the incremental exercise test on the lactate minimum speed (LMS). Thirteen sprinters and 12 endurance runners performed the following tests: 1) a maximal 500 m sprint followed by a passive recovery to determine the time to reach the peak blood lactate concentration; 2) after the maximal 500 m sprint, the athletes rested eight mins, and then performed 6 x 800 m incremental test, in order to determine the speed corresponding to the lower blood lactate concentration (LMS1) and; 3) identical procedures of the LMS1, differing only in the passive rest time, that was performed in accordance with the time to peak lactate (LMS2). The time (min) to reach the peak blood lactate concentration was significantly higher in the sprinters (12.76+/-2.83) than in the endurance runners (10.25+/-3.01). There was no significant difference between LMS1 and LMS2, for both endurance (285.7+/-19.9; 283.9+/-17.8 m/min; r= 0.96) and sprint runners (238.0+/-14.1; 239.4+/-13.9 m/min; r= 0.93), respectively. We can conclude that the LMS is not influenced by a passive recovery period longer than eight mins (adjusted according with the time to peak blood lactate), although blood lactate concentration may differ at this speed. The predominant type of training (aerobic or anaerobic) of the athletes does not seem to influence the phenomenon previously described.

Ventricular remodeling and diastolic myocardial dysfunction in rats submitted to protein-calorie malnutrition

The effects of protein-calorie malnutrition (PCM) on heart structure and function are not completely understood. We studied heart morphometric, functional, and biochemical characteristics in undernourished young Wistar rats. They were submitted to PCM from birth (undernourished group, UG). After 10 wk, left ventricle function was studied using a Langendorff preparation. The results were compared with age-matched rats fed ad libitum (control group, CG). The UG rats achieved 47% of the body weight and 44% of the left ventricular weight (LVW) of the CG. LVW-to-ventricular volume ratio was smaller and myocardial hydroxyproline concentration was higher in the UG. Left ventricular systolic function was not affected by the PCM protocol. The myocardial stiffness constant was greater in the UG, whereas the end-diastolic pressure-volume relationship was not altered. In conclusion, the heart is not spared from the adverse effects of PCM. There is a geometric alteration in the left ventricle with preserved ventricular compliance despite the increased passive myocardial stiffness. The systolic function is preserved.

Rotor support stiffness estimation by sensitivity analysis

In the present work, a method for rotor support stiffness estimation via a model updating process using the sensitivity analysis is presented. This method consists in using the eigenvalues sensitivity analysis, relating to the rotor support stiffnesses variation to perform the adjustment of the model based on the minimization of the difference between eigenvalues of reference and eigenvalues obtained via mathematical model from previously adopted support bearing stiffness values. The mathematical model is developed by the finite element method and the method of adjustment should converge employing an iterative process. The performance and robustness of the method have been analyzed through a numerical example.

Electrochemical impedance spectroscopy characterization of passive film formed on implant Ti-6Al-7Nb alloy in Hank's solution

The influence of potential on electrochemical behavior of Ti-6Al-7Nb alloy under simulate physiological conditions was investigated by electrochemical impedance spectroscopy (EIS). The experimental results were compared with those obtained by potentiodynamic polarization curves. All measurements were carried out in Hank's aerated solution at 25degreesC, at pH 7.8 and at different potentials (corrosion potential, 0 mV(SCE), 1000 mV(SCE), and 2000 mV(SCE)). The EIS spectra exhibited a two-step or a two-time constant system, suggesting the formation of a two-layer oxide film on the metal surface. The high corrosion resistance, displayed by this alloy in electrochemical polarization tests, is due to the dense inner layer, while its osseointegration ability can be ascribed to the presence of the outer porous layer. (C) 2004 Kluwer Academic Publishers.

THE LONG-TERM EVOLUTION OF IMMUNE DEPOSITS IN PASSIVE HEYMANN NEPHRITIS

1. To study the long term course of passive Heymann nephritis (PHN), 42 adult male Wistar rats were injected with rabbit anti-FX1A serum (PHN group) and 42 rats received normal rabbit serum (control group). Two animals from each group were sacrificed 2 weeks after the inoculation and 10 animals each from the control and PHN groups were sacrificed 4, 13, 25 and 53 weeks later.2. The PHN group exhibited a significant elevation in 20-h proteinuria which lasted from the first week (control group, 9.19 +/- 0.87; PHN group, 25.3 +/- 2.66) to the 25th week (control group, 22.6 +/- 2.15; PHN group, 66.7 +/- 10.4) except for week 17. From week 29 to week 53 there was no statistical difference between the 2 groups.3. Light microscopy showed no difference between the kidneys of PHN and control rats. Immunofluorescence microscopy in PHN rats showed granular deposition of autologous and heterologous IgG on the glomerular basement membrane (GBM), whose intensity and pattern did not change during 53 weeks of observation.4. When examined by electron microscopy the glomeruli of PHN rats showed: a) electron-dense deposits which were initially subepithelial and homogeneous and later intramembranous, granular and often surrounded by an electron-transparent halo; b) focal thickening of the GBM at the sites of intramembranous deposits; c) effacement of podocytes located close to the deposits; d) penetration of the podocytes into the GBM associated with the deposits; e) presence of osmiophilic granules in the cytoplasm of the podocyte located inside the GBM similar to the granules of the deposits next to them. The association of the penetration of the podocytes into the GBM with the deposits and the presence of the osmiophilic granules inside the foot process have not been described previously in PHN.5. The results suggest that the podocytes play a role in the clearing of intramembranous deposits in PHN.