Investigation on Surface Finishing of Components Ground with Lapping Kinematics: Lapgrinding Process

Over the last three decades, researchers have responded to the demands of industry to manufacture mechanical components with geometrical tolerance, dimensional tolerance, and surface finishing in nanometer levels. The new lapgrinding process developed in Brazil utilizes lapping kinematics and a flat grinding wheel dressed with a single-point diamond dresser in agreement with overlap factor (U(d)) theory. In the present work, the influences of different U(d) values on dressing (U(d) = 1, 3 e 5) and grain size of the grinding wheel made of silicon carbide (SiC = 800, 600 e 300 mesh) are analyzed on surface finishing of stainless steel AISI 420 flat workpieces submitted to the lapgrinding process. The best results, obtained after 10 minutes of machining, were: average surface roughness (Ra) 1.92 nm; 1.19 mu m flatness deviation of 25.4 mm diameter workpieces and mirrored surface finishing. Given the surface quality achieved, the lapgrinding process can be included among the ultra-precision finishing processes and, depending on the application, the steps of lapping followed by polishing can be replaced by the proposed abrasive process.

Waveshapes of continuing currents and properties of M-components in natural positive cloud-to-ground lightning

This work analyses the waveshapes of continuing currents and parameters of M-components in positive cloud-to-ground (CG) flashes through high-speed GPS synchronized videos. The dataset is composed of only long continuing currents (with duration longer than 40 ms) and was selected from more than 800 flashes recorded in Sao Jose dos Campos (45.864 degrees W, 23.215 degrees S) and Uruguaiana (29.806 degrees W, 57.005 degrees S) in Southeast and South of Brazil, respectively, during 2003 to 2007 summers. The videos are compared with data obtained by the Brazilian Lightning Location System (BrasilDAT) in order to determine the polarity of each flash and select only positive cases. There are only two studies of waveshapes of continuing currents in the literature. One is based on direct current measurements of triggered lightning, in which four different types of waveshapes were observed; and the other is based on measurements of luminosity variations in high-speed videos of CG negative lightning, in which besides the four types above mentioned two additional types were observed. The present work is an extension of the latter, using the same method but now applied to obtain the waveshapes of positive CG lightning. As far as the authors know, this is the first report on M-components in positive continuing currents. We also have used the luminosity-versus-time graphs to observe their occurrence and measure some parameters (duration, elapsed time and time between two successive M-components), whose statistics are presented and compared in detail to the data for negative flashes. We have plotted a histogram of the M-components elapsed time over the total duration of the continuing current for positive flashes, which presented an exponential decay (correlation coefficient: 0.83), similar to what has been observed for negative flashes. (C) 2008 Elsevier B.V. All rights reserved.

Improvement in the fatigue strength of chromium electroplated AISI 4340 steel by shot peening

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Real power losses reduction and loading margin improvement via continuation method

This letter presents an alternative approach for reducing the total real power losses by using a continuation method. Results for two simple test systems and for the IEEE 57-bus system show that this procedure results in larger voltage stability margin. Besides, the reduction of real power losses obtained with this procedure leads to significant money savings and, simultaneously, to voltage profile improvement. Comparison between the solution of an optimal power flow and the proposed method shows that the latter can provide near optimal results and so, it can be a reasonable alternative to power system voltage stability enhancement.

Spatial distribution of trachoma cases in the City of Bauru, State of São Paulo, Brazil, detected in 2006: defining key areas for improvement of health resources

Introduction: The objective of this study was to analyze the spatial behavior of the occurrence of trachoma cases detected in the City of Bauru, State of São Paulo, Brazil, in 2006 in order to use the information collected to set priority areas for optimization of health resources. Methods: the trachoma cases identified in 2006 were georeferenced. The data evaluated were: schools where the trachoma cases studied, data from the 2000 Census, census tract, type of housing, water supply conditions, distribution of income and levels of education of household heads. In the Google Earth® software and TerraView® were made descriptive spatial analysis and estimates of the Kernel. Each area was studied by interpolation of the density surfaces exposing events to facilitate to recognize the clusters. Results: of the 66 cases detected, only one (1.5%) was not a resident of the city's outskirts. A positive association was detected of trachoma cases and the percentage of heads of household with income below three minimum wages and schooling under eight years of education. Conclusions: The recognition of the spatial distribution of trachoma cases coincided with the areas of greatest social inequality in Bauru City. The micro-areas identified are those that should be prioritized in the rationalization of health resources. There is the possibility of using the trachoma cases detected as an indicator of performance of micro priority health programs.

Ground annatto seeds (Bixa orellana L.) in sorghum-based commercial layer diets and their effects on performance, egg quality, and yolk pigmentation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Serum progesterone concentration and conception rate of beef cows supplemented with ground corn after a fixed-time artificial insemination protocol

Avaliaram-se os efeitos de diferentes níveis de ingestão de suplemento com milho moído finamente (MF) em vacas de corte, mantidas em pasto, após inseminação artificial em tempo fixo (IATF), sobre a concentração sérica de progesterona (P4) no dia 7, e sobre a concepção no dia 28 pós IATF. Trezentas e sessenta e quatro vacas Brangus, multíparas lactantes, tiveram as atividades folicular e luteal sincronizadas por tratamento com benzoato de estradiol (Estrogin; 2,0mg IM) e inserção de dispositivo intravaginal de P4 (CIDR) no dia -11, seguido por tratamento com PGF2 α (Lutalyse; 25mg IM) no dia - 4, retirada do CIDR e remoção temporária de bezerros no dia -2, e tratamento com GnRH (Fertagyl; 100 µ g IM), IATF e retorno dos bezerros no dia 0. No dia 0, as vacas foram aleatoriamente distribuídas para receber um dos quatro tratamentos: G1 -2kg/dia de MF do dia 0 ao dia 21; G2 -2kg/dia de MF do dia 0 ao dia 7, e 6kg/dia de MF do dia 8 ao dia 21; G3 -6kg/dia de MF do dia 0 ao dia 7, e 2kg/dia de MF do dia 8 ao dia 21; G4 -6kg/dia de MF do dia 0 ao dia 21. Amostras de sangue foram colhidas no dia 7, e o diagnóstico de gestação foi realizado por ultrassonografia no dia 28. As vacas suplementadas com 2kg/dia de MF apresentaram maior concentração sérica de P4 no dia 7 em relação às vacas suplementadas com 6kg/dia (1,58 vs. 1,28ng/mL; P<0,01, EPM=0,08). As vacas do G4 apresentaram maior taxa de concepção em relação às vacas do G1 (58,4 vs. 41,9%, respectivamente; P<0,05). O nível de consumo do suplemento energético após a IATF é negativamente associado às concentrações séricas de P4, porém positivamente associado à taxa de concepção em vacas de corte em pasto.

Improvement of embryo production by the replacement of the last two doses of porcine follicle-stimulating hormone with equine chorionic gonadotropin in Sindhi donors

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Improvement in embryo recovery using double uterine flushing

The objective of the present study was to evaluate the effects of double uterine flushing on the recovery of embryos/ova in cattle. Two hundred and ten embryo recovery procedures were conducted using a double uterine flushing method, and the results were compared with 432 conventional single-flushing procedures. Cyclic Limousin (n = 403) and Guzera (n = 239) donor cows received an intravaginal progesterone releasing device and 2 mg of estradiol benzoate on Day 0. Between Days 5 and 9, donors received decreasing doses of FSH, which ranged from 200 to 300 IU (Bos indicus) and 300 to 500 IU (Bos taut-us). on the afternoon of Day 7, donors received an injection of 500 mu g cloprostenol and progesterone implants were removed 12 It later (morning of Day 8). Artificial insemination was performed between 14 and 26 h after first detection of behavioral estrus. Cows were randomly assigned to have embryos recovered by a double-flushing method (n = 210) or the conventional single-flushing procedure (n = 432). For the double-flushing procedure, after first flushing the whole uterus with 1 L of Dubelco's Phosphate Buffered Saline (DPBS), a Foley catheter was positioned in the uterine body to permit refilling of the uterus with fresh DPBS (80-150 mL). The catheter was closed with the plunger of a disposable 5 mL syringe, and the donors were allowed to rest in a holding area for 30 min. Thereafter, a second flush was performed to recover the solution remaining in the uterus. Animals from the control group were subjected to a single uterine flush. From 2 10 double-flushing procedures, 1409 viable embryos were recovered. In comparison, from 432 cows receiving the single-flushing procedure, 1993 embryos were recovered. Double flushing increased (P < 0.05) the number of embryos recovered per procedure compared to single flushing (6.7 +/- 0.4 versus 4.6 +/- 0.2, respectively; mean +/- S.E.M.). When double flushing was performed, average recovered embryos/ova increased (P < 0.05) from 8.3 +/- 0.4 to 12.7 +/- 0.7 in Limousin and from 7.9 to 11.5 in Guzera. Also, utilization of double flushing increased (P < 0.05) the number of viable embryos from 4.7 +/- 0.3 to 6.9 +/- 0.5 in Limousin and from 4.5 +/- 0.4 to 6.4 +/- 0.7 in Guzera. Mean total embryos/ova was similar (P > 0.05) between the control group and after the first uterine flushing in the double-flushing group; therefore, both flushings were conducted efficiently. In conclusion, double uterine flushing increased embryo recovery in cattle. (C) 2004 Elsevier B.V. All rights reserved.

Foreign Body in Preauricular Region

Foreign bodies, although they are often found throughout the body, to a lesser degree in the face, still constitute a diagnostic challenge for the trauma surgeon. Its removal means danger of damaging important facial anatomic structures, even if its exact position from the image data was known. So, the objective is to describe a clinical report of a patient (42 years of age, male sex) who experienced falling to the ground, attended by the Department of Surgery and Traumatology Bucco-Maxillo-Facial Surgery, Faculty of Dentistry of Aracatuba, São Paulo State University, and 2 days after the trauma, he reported difficulty in mouth opening and pain. After clinical evaluation, we observed the presence of injury in the left preauricular region already in the process of healing. During the intraoral physical examination, a limitation of the mouth opening was noted. Radiographic posteroanterior and profile of the face showed 2 radiopaque foreign bodies in the left side, lying apparently at the region of the mandibular condylar process. Under local anesthesia, foreign body removal was carried from there with access to it through the preexisting facial injury. Further clinical examinations showed an improvement in mouth opening, absence of pain complaints, and/or functional complaints.

Analysis of Masticatory Cycle Efficiency in Complete Denture Wearers

Purpose: This study assessed masticatory efficiency and duration of the masticatory cycle in 14 asymptomatic patients with severe bone resorption. All patients had worn complete dentures for over 10 years. Recall visits were scheduled at 5 months and 1 year after receiving new dentures.Materials and Methods: Fourteen patients were evaluated in this study. The Research Diagnostic Criteria questionnaire and tests of the efficiency and duration of the masticatory cycle were performed with artificial food before, 5 months after, and 1 year after new dentures were delivered. Masticatory efficiency was assessed using a sieve system; artificial food was ground for 35 masticatory cycles and monitored by the operator.Results: Masticatory efficiency at 5 months was significantly improved for the 0.42-mm mesh. An improvement in masticatory efficiency and a reduction in mastication time were observed with the new dentures after 1 year.Conclusion: The results of this study indicated that 5 months did not allow enough time to demonstrate improved muscular capacity and ability after receiving new dentures. After 1 year, the duration of the masticatory cycle was reduced, and masticatory efficiency was significantly improved.

The influence of temperature of three adhesive systems on bonding to ground enamel

This study evaluated the microtensile bond strength test (mu T), micromorphology of resin-enamel interface (RET) and etching patterns (EP) promoted by the etch-and-rinse adhesive, Prime&Bond NT (PB), and two self-etching adhesives, Clearfil SE Bond (SE) and Adper Prompt L-Pop (APR), to ground bovine enamel surfaces' when applied at temperatures of 5 degrees C (C), 40 degrees C (H) and 20 degrees C (R). Materials and Methods. Sixty-three bovine incisors were randomly divided into nine experimental groups (n=7) according to adhesive systems and temperatures. The buccal enamel surfaces were flattened with 600-grit SiC paper and abraded with a diamond bur under water-cooling. The adhesive systems were applied according to the manufacturer's instructions. After the restorative procedures, the specimens were sectioned into five slabs. Four slabs were prepared for mu T and one for interface analysis. For etching pattern analysis, the remaining 16 bovine enamel fragments were used (n=2). The adhesives were applied and the surfaces were rinsed with organic solvents after application. The specimens for RET and EP analysis were prepared for SEM analysis. Results. No significant differences among the adhesives were found at R temperature. However, at 5 degrees C, PB and APR presented lower bond strength than SE. At H temperature, higher bond strength was observed for PB than for APR and SE. At C and H temperature, formation of the interdiffusion zone was impaired and the treated enamel surfaces presented an undefined EP.

IMPROVEMENT TO THE MARGINAL COPING FIT of COMMERCIALLY PURE TITANIUM CAST IN PHOSPHATE-BONDED INVESTMENT BY USING A SIMPLE PATTERN COATING TECHNIQUE

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)