Influência do aparelho fotoativador na resistência ao desgaste de compósitos restauradores

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise termoeconômica e ecológica da incorporação do processo de produção de hidrogênio em uma planta de produção de biodiesel

Pós-graduação em Engenharia Mecânica - FEG

Estudo da viabilidade técnica, econômica e ambiental da substituição de um banco de resistências elétricas de aquecedores por uma caldeira alimentada por biomassa de paletes residuais na indústria de laminação

Given the increasing demand for fossil fuels to power the engines of the global economy, and also the slow process of synthesis of oil, it becomes necessary to develop new sources of renewable energy in addition to improve promising sources that already exist, turning them competitive. Based on this, biomass is shown very promising between the most popular energy sources due to its availability, applicability, and above all, the fact of not emitting green house gases when analyzing the whole carbon cycle. In this sense, this work presents, through an environmental, technical and economic analysis, the impact in an aluminum mill of replacing the use of electricity, in one process, by a boiler fueled with biomass from waste process of packaging the finished product with pallets. Thus, besides the reduction of CO2 emissions, financial gains are targeted, since the main goal of the corporations that require such power is to maximize its profits

Aspectos técnicos e ambientais da incorporação de novas tecnologias no setor sucroalcooleiro: produção de hidrogênio e gaseificação do bagaço

The purpose of this work is to study the incorporation of hydrogen production (Case A) and the process of gasification of sugarcane bagasse associated with combined cycle gas turbine and steam turbine (Case B) for Distillery Pioneers process. These technologies can be used to improve the energy supply in the sugarcane mill. Initially the processes for obtaining sugar and ethanol from sugarcane is discussed, with a theoretical introduction to hydrogen, the process of steam reforming and gasification of biomass (bagasse) by inserting a turbine associated with the recovery boiler gas. Subsequently makes up the energy and exergy analysis of the incorporation of the above technologies. In end stage makes it an ecological analysis considering or not the carbon cycle (photosynthesis), to determine the levels of emissions of pollutants, carbon dioxide equivalent, indicators of pollution and ecological efficiencies associated with technological developments proposed. It is concluded that hydrogen production by steam reforming of ethanol and gasification of bagasse are viable alternatives from the point of view of technical and environmental applications in the biofuels industry, contributing to the development of the sector in the country

Análise funcional de um consórcio microbiano de solo e prospecção de genes envolvidos na desconstrução da biomassa

Pós-graduação em Microbiologia Agropecuária - FCAV

Estrutura e funcionamento da alça microbiana nos sedimentos da Baía do Araçá, São Sebastião - SP

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The calcium looping cycle study for capturing carbon dioxide applied to the energy generation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Electrically, Chemically, and Photonically Powered Torsional and Tensile Actuation of Hybrid Carbon Nanotube Yarn Muscles

Artificial muscles are of practical interest, but few types have been commercially exploited. Typical problems include slow response, low strain and force generation, short cycle life, use of electrolytes, and low energy efficiency. We have designed guest-filled, twist-spun carbon nanotube yarns as electrolyte-free muscles that provide fast, high-force, large-stroke torsional and tensile actuation. More than a million torsional and tensile actuation cycles are demonstrated, wherein a muscle spins a rotor at an average 11,500 revolutions/minute or delivers 3% tensile contraction at 1200 cycles/minute. Electrical, chemical, or photonic excitation of hybrid yarns changes guest dimensions and generates torsional rotation and contraction of the yarn host. Demonstrations include torsional motors, contractile muscles, and sensors that capture the energy of the sensing process to mechanically actuate.

Combined cycle versus one thousand diesel power plants: pollutant emissions, ecological efficiency and economic analysis

The increase in the use of natural gas in Brazil has stimulated public and private sectors to analyse the possibility of using combined cycle systems for generation of electrical energy. Gas turbine combined cycle power plants are becoming increasingly common due to their high efficiency, short lead times, and ability to meet environmental standards. Power is produced in a generator linked directly to the gas turbine. The gas turbine exhaust gases are sent to a heat recovery steam generator to produce superheated steam that can be used in a steam turbine to produce additional power. In this paper a comparative study between a 1000 MW combined cycle power plant and 1000 kW diesel power plant is presented. In first step, the energetic situation in Brazil, the needs of the electric sector modification and the needs of demand management and integrated means planning are clarified. In another step the characteristics of large and small thermoelectric power plants that use natural gas and diesel fuel, respectively, are presented. The ecological efficiency levels of each type of power plant is considered in the discussion, presenting the emissions of particulate material, sulphur dioxide (SO2), carbon dioxide (CO2) and nitrogen oxides (NOx). (c) 2006 Elsevier Ltd. All rights reserved.

Hygrothermal effects on the shear properties of carbon fiber/epoxy composites

The environmental factors, such as humidity and temperature, can limit the applications of composites by deteriorating the mechanical properties over a period of time. Environmental factors play an important role during the manufacture step and during composite's life cycle. The degradation of composites due to environmental effects is mainly caused by chemical and/or physical damages in the polymer matrix, loss of adhesion at the fiber/matrix interface, and/or reduction of fiber strength and stiffness. Composite's degradation can be measure by shear tests because shear failure is a matrix dominated property. In this work, the influence of moisture in shear properties of carbon fiber/epoxy composites ( laminates [0/0](s) and [0/90](s)) have been investigated. The interlaminar shear strength (ILSS) was measured by using the short beam shear test, and Iosipescu shear strength and modulus (G(12)) have been determinated by using the Iosipescu test. Results for laminates [0/0](s) and [0/90](s), after hygrothermal conditioning, exhibited a reduction of 21% and 18% on the interlaminar shear strenght, respectively, when compared to the unconditioned samples. Shear modulus follows the same trend. A reduction of 14.1 and 17.6% was found for [0/0](s) and [0/90](s), respectively, when compared to the unconditioned samples. Microstructural observations of the fracture surfaces by optical and scanning electron microscopies showed typical damage mechanisms for laminates [0/0](s) and [0/90](s).

Monitoring of cure kinetic prepreg and cure cycle modeling

Cure kinetic model is an integral part of composite process simulation, which is used to predict the degree of curing and the amount of the generated heat. The parameters involved in kinetic models are usually determined empirically from isothermal or dynamic differential scanning calorimetry (DSC) data. In this work, DSC and rheological techniques were used to investigate some of the kinetic parameters of cure reactions of carbon/F161 epoxy prepreg and to evaluate the cure cycle used to manufacture polymeric composites for aeronautical applications. As a result, it was observed that the F161 prepreg presents cure kinetic with total order 1.2-1.9. (c) 2006 Springer Science + Business Media, Inc.

Evaluation of fatigue behavior on repaired carbon fiber/epoxy composites

The continuous use of structural polymer composites in aeronautical industry has required the development of repairing techniques of damages found in different types of laminates. The most usually adopted procedure to investigate the repair of composite laminates has been by repairing damages simulated in laminated composite specimens. This work shows the influence of structural repair technique on mechanical properties of a typical carbon fiber/epoxy laminate used in aerospace industry. When analyzed by tensile test, the laminates with and without repair present tensile strength values of 670 and 892 MPa, respectively, and tensile modulus of 53.0 and 67.2 GPa, respectively. By this result, it is possible to observe a decrease of the measured mechanical properties of the repaired composites. When submitted to fatigue test, it is observed that in loads higher than 250 MPa, this laminate presents a low life cycle (lower than 400,000 cycles). The fatigue performance of both laminates is comparable, but the non-repaired laminate presented higher tensile and fatigue resistance when compared with the repaired laminate.

Stripping voltammetry of mercury(II) with a chemically modified carbon paste electrode containing silica gel functionalized with 2,5-dimercapto-1,3,4-thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5-dimercapto-1,3,4-thiadiazole (DTTPSG-CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range -0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L-1 KNO3; nu=20 mV s(-1)) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG-CPE. The anodic wave peak at 0.31 V is well-defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, cleaning solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg (L)-(1) Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.

Muscle delta C-13 change in Nile tilapia (Oreochromis niloticus): Effects of growth and carbon turnover

The contribution of growth and turnover to the muscle delta C-13 change process was investigated using mathematical models which associate delta C-13 change to time of intake of a new diet or increase in body mass. Two groups of Nile tilapia (Oreochromis niloticus) were fed on diets based on C3 (sigma C-13 = - 25.64 +/- 0.06 parts per thousand) or C4 (delta C-13= -16.01 +/- 0.06 parts per thousand) photosynthetic cycle plants to standardize the muscle delta C-13. After establishing the carbon isotopic equilibrium, fish (mean mass 24.12 +/- 6.79 g) then received the other treatment diet until a new carbon isotopic equilibrium could be established, characterizing T1 (C3-C4) and T2 (C4-C3) treatments. No significant differences were observed in fish productive performance. Good fits were obtained for the models that associated the delta C-13 change to time, resulting in carbon half-life values of 23.33 days for T1 and 25.96 days for T2. Based on values found for the muscle delta C-13 change rate from growth (0.0263 day(-1) and 0.0254 day(-1)) and turnover (0.0034 day(-1) and 0.0013 day(-1)), our results indicate that most of the delta C-13 change could be attributed to growth. The application of model that associated the delta C-13 change to body mass increase seems to produce results with no apparent biological explanation. The delta C-13 change rate could directly reflect the daily ration and growth rate, and consequently the isotopic change rates of carbon and other tissue elements can be properly used to assess different factors that may interfere in nutrient utilization and growth. (c) 2006 Published by Elsevier B.V.

Carbon isotope analysis in apple nectar beverages

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)