Growth rates in modern speleothems from Santana Cave, Brazil, by the Pb-210-method

The Santana Cave is located at the Upper Ribeira Touristic State Park (PETAR-Parque Estadual Turistico do Alto Ribeira) in southern São Paulo State, Brazil. This paper describes Pb-210 activity concentration data in soda straw stalactites samples collected at Salao das Flores in Santana Cave that is a fossil tributary of the cave river. Non-expensive alpha counting following some analytical steps for extracting and depositing Pb-210 were used for providing the Pb-210 data. In the analyzed samples, Pb-210 values of increasingly older samples fitted an exponential curve, thus suggesting that the production of Pb-210 has been constant with time. Also, the near-ideal fit indicated that the growth was uniform and there was no break in the continuous growth. The soda straw growth rates were determined from the best fit to the exponential curve through the Pb-210 activity concentration. The results of the measurements allowed estimate a longitudinal rate corresponding to 1.3 mm/yr and a lateral rate of 0.01 mm/yr, which permitted calculate times of 70 years and 317-498 years for their formation, respectively. The lateral growth rate is compatible with values from studies of chemical weathering rates held under laboratory and natural conditions. (C) 2011 Elsevier Ltd. All rights reserved.

Controlling Excitation Inversion of a Cooper Pair Box Interacting with a Nanomechanical Resonator

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of cavity preparation and curing method on the marginal seal of resin composite restorations: an in vitro evaluation.

OBJECTIVE: To evaluate the influence of cavity design and photocuring method on the marginal seal of resin composite restorations. METHOD AND MATERIALS: Seventy-two bovine teeth were divided into 2 groups: group 1 received box-type cavity preparations, and group 2 received plate-type preparations. Each group was divided into 3 subgroups. After etching and bonding, Z250 resin composite (3M Espe) was applied in 2 equal increments and cured with 1 of 3 techniques: (1) conventional curing for 30 seconds at 650 mW/cm2; (2) 2-step photocuring, in which the first step was performed 14 mm from the restoration for 10 seconds at 180 mW/cm2 and the second step was performed in direct contact for 20 seconds at 650 mW/cm2; or (3) progressive curing using Jetlite 4000 (J. Morita) for 8 seconds at 125 mW/cm2 and then 22 seconds at 125 mW/cm2 up to 500 mW/cm2. The specimens were thermocycled for 500 cycles and then submitted to dye penetration with a 50% silver nitrate solution. Microleakage was assessed using a stereomicroscope. Data were analyzed using analysis of variance and Tukey test (5% level of significance). RESULTS: A statistically significant difference was found between groups when a double interaction between photocuring and cavity preparation was considered (P = .029). CONCLUSIONS: No one type of cavity preparation or photocuring method prevented micro-leakage. The plate-type preparation showed the worst dye penetration when conventional and progressive photocuring methods were used. The best results were found using the 2-step photocuring with the plate-type preparation.

An automatic method for segmentation of fission tracks in epidote crystal photomicrographs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The bias in reversing the Box-Cox transformation in time series forecasting: An empirical study based on neural networks

The Box-Cox transformation is a technique mostly utilized to turn the probabilistic distribution of a time series data into approximately normal. And this helps statistical and neural models to perform more accurate forecastings. However, it introduces a bias when the reversion of the transformation is conducted with the predicted data. The statistical methods to perform a bias-free reversion require, necessarily, the assumption of Gaussianity of the transformed data distribution, which is a rare event in real-world time series. So, the aim of this study was to provide an effective method of removing the bias when the reversion of the Box-Cox transformation is executed. Thus, the developed method is based on a focused time lagged feedforward neural network, which does not require any assumption about the transformed data distribution. Therefore, to evaluate the performance of the proposed method, numerical simulations were conducted and the Mean Absolute Percentage Error, the Theil Inequality Index and the Signal-to-Noise ratio of 20-step-ahead forecasts of 40 time series were compared, and the results obtained indicate that the proposed reversion method is valid and justifies new studies. (C) 2014 Elsevier B.V. All rights reserved.

Structural characterization of Li-MN doped powders prepared by Pechini's method

Pechini's method has been successfully used to prepare Li-doped MgNb2O6(MN) at short time and low temperature. It consists in the preparation of metal citrate solution, which is polymerized at 250°C to form a high viscous resin. This resin was burned in a box type furnace at 400°C/2h and ground in a mortar. Successive steps of calcination up to 900°C were used to form a crystalline precursor. SEM, DTA and XRD were used to characterize the powders. MN precursor powders containing from 0.1 to 5.0 mol% of LiNbO3 additive was prepared aiming better dielectric properties and microstructural characteristics of the PMN prepared from columbite route. SEM analysis showed that particles increased by sintering, forming large agglomerates. The surface area is also substantially reduced with the increase in additive amount above 1.0 mol%. In XRD pattern of the precursor material with 5.0 mol% of additive was observed the LiNbO3 phase of trigonal structure. XRD data were used for Rietveld refinement and a decrease in microstrain and pronounced increase in crystallite size with the increase of LiNbO3 were observed. It is in agreement with the particle morphologies observed by SEM analysis.