Electrochemical Determination of Inorganic Contaminants in Automotive Fuels

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Polycyclic aromatic hydrocarbons from wood pyrolyis in charcoal production furnaces

Polycyclic aromatic hydrocarbons (PAH) were measured in smoke samples from wood carbonization during charcoal production, in both particulate matter (PM) and gaseous phases. Samples were acquired using a medium-volume air sampler at 1.5 m distance from the furnace. Particle-bound PAH were collected on Fluoropore polytetrafluoroethylene filters and gas-phase PAH were collected into sorbent tubes with XAD-2 resin. PAH were extracted with dichloromethane-methanol and analyzed using gas chromatography-mass spectrometry. The results showed total emission from the furnace of 26 mu g/m(3) for the 16 PAH and 2.8 mu g/m(3) for the 10 genotoxic PAH (from fluoranthene to benzo[g,h,i]perylene). High emission of 16 PAH in the first 8 h of wood carbonization was detected (64 mu g/m(3); 56% of the total emission). Associated with PM, 11% of the total emission of 16 PAH (in both phases) and 60% of 10 genotoxic PAH were found. Relative ratios (for example, [Phe]/[Phe] + [Ant]) for the PAH of the same molecular weight were obtained and compared with the published data. The concentrations of benzo[a]pyrene equivalent (BaPeq) were estimated using the list of toxic equivalent factors suggested by Nisbet and LaGoy, 1992. The values of 0.30 and 0.06 mg/m3 were obtained for the total concentrations of BaPeq in PM and gaseous phase, respectively. (c) 2006 Elsevier B.V. All rights reserved.

Identification of polycyclic aromatic hydrocarbons and methoxylated phenols in wood smoke emitted during production of charcoal

More than 130 organic substances in dichloromethane-methanol (4: 1) extracts of particulate matter and the gaseous phase from wood burning for the production of charcoal have been identified by capillary gas chromatography coupled with low-resolution mass spectrometry (GC-MS), use of GC retention indices, and comparison with authentic standards. Many of the substances identified are methoxyphenols (derivatives of syringol and guaiacol), polycyclic aromatic hydrocarbons (PAH), oxidized PAH (oxy-PAH), and levoglucosan, the last being a monosoccharide derivative from the thermal breakdown of cellulose. The amount of unsubstituted PAH was greater than that of methyl- and dimethyl-substituted homologs.

A square-wave voltammetric method for analysing the colour marker quinizarine in petrol and diesel fuels

This work presents an electroanalytical method based on square-wave voltammetry (SWV) for the determination of quinizarine (QNZ) in a mixture of Britton-Robinson buffer 0.08 mol L-1 with 30% of acetonitrile. The QNZ was oxidized at glassy carbon electrode in and the well-defined peak at +0.45 V vs. Ag/AgCl can be used for its determination as colour marker in fuel samples. All parameters were optimized and analytical curves can be constructed for QNZ concentrations ranging from 2.0 x 10(-6) mol L-1 to 1.4 x 10(-5) mol L-1, using f = 60 Hz and E-sw = 25 mV. The method offers a limit detection of 4.12 x 10(-7) mol L-1 and a standard deviation of 4.5% when six measurements of 1.25 x 10(-5) mol L-1 are compared. The method was successfully applied for determining QNZ in gasoline and diesel oil and the obtained results showed good agreement with those reported previously. (c) 2006 Elsevier Ltd. All rights reserved.

Comparative wood anatomy of root and stem in Styrax camporum (Styracaceae)

Styrax camporum Pohl is a shrub common in the cerrado vegetation of south-eastern Brazil. Root and stem wood in Styrax camporum differ quantitatively and qualitatively. Quantitative differences follow normal expectations: roots have wider and longer vessel elements, a lower vessel frequency, a lower ray frequency, and wider rays. Qualitative features of the roots are: simple perforation plates, vestured pits, and septate libriform fibres; qualitative features of the stems are: multiple perforation plates, non-vestured pits, and non-septate fibre-tracheids. Based on generally accepted evolutionary trends, root wood of Styrax camporum has more specialized features than stem wood. Additional comparative studies of stem and root anatomy are needed to determine if such differences between root and stem anatomy are widespread, and consistent with the lines of specialization observed in monocotyledons.

A case study of compact cogeneration using various fuels

A method for studying the technical and economic feasibility of absorption refrigeration systems in compact cogenerators is presented. The system studied consists of an internal combustion engine, an electric generator and a heat exchanger to recover residual heat from the refrigeration water and exhaust gases. As an application, a computer program simulates the cogeneration system in a building which already has 75 kW of installed electric power. The maximum electric and refrigeration demands are 45 kW and 76 kW respectively. This study simulates the system performance, utilizing diesel oil, sugar cane alcohol and natural gas as possible fuels. (C) 1997 Elsevier B.V. Ltd.

Estimating the aboveground biomass and wood volume of savanna woodlands in Brazil's Pantanal wetlands based on allometric correlations

The quantity and distribution of vegetal biomass are important aspects to consider in ecosystem studies. However, little information is available about Brazil's Pantanal woodland savannas. This work involved the development of regression equations of the aerial biomass and wood volume of native tree species in a region of woodland savanna on Rio Negro farm in the Pantanal of Nhecolandia, Brazil. Samples were taken from 10 trees of each of five species: Protium heptaphyllum (Aub1.) Marchand, Magonia pubescens A. St.-Hil., Diptychandra aurantiaca Tul., Terminalia argentea Mart. and Zucc. and Licania minutiflora (Sagot) Fritsch and from a miscellaneous group of I I different species. Linear and nonlinear regression analyses were developed relating the diameter at breast height to the dry weight of wood, branches and leaves, wood volume and total aerial biomass. All the regressions showed a significance of P < 0.05 and an R-2 close to or above 0.8. The biomass curve predicted by linear regression analysis of the studied species was similar to the nonlinear regression, with the exception of L. minutiflora and the miscellaneous group. The breast height diameter proved a good choice for estimating biomass and wood volume. The estimated wood volume and biomass of the Pantanal woodland savanna is crucial information for understanding the carbon cycle and for ensuring the region's conservation and sustainable use. (c) 2006 Elsevier B.V. All rights reserved.

Influence of Wood Moisture Content on the Modulus of Elasticity in Compression Parallel to the Grain

Brazilian Standard ABNT NBR7190:1997 for timber structures design, adopts a first degree equation to describe the influence of wood moisture content. Periodically, when necessary, the referred standard is revised in order to analyze inconsistencies and to adopt considerations according new realities verified. So, the present paper aims to examine the adequacy of its equation which corrects to 12% of moisture the values of rigidity properties obtained on experimental tests. To quantify the moisture influence on modulus of elasticity, it was applied tests of compression parallel to the grain for six specimens of different strength classes, considering nominal moisture of 12; 20; 25; 30%. As results, modulus of elasticity in the moisture range 25-30% showed statistically equivalents, and was obtained a first degree equation to correlate the studied variables which leads to statically equivalent estimations when compared with results by ABNT NBR7190:1997 equation. However, it was indicated to maintain the current expression for the next text of the referred document review, without prejudice to statistical significance of the estimates.

Development of successive cambia and structure of wood in Gallesia integrifolia (Spreng.) Harms (Phytolaccaceae)

Stem diameter in Gallesia integrifolia (Spreng.) Harms (Phytolaccaceae) increases by forming concentric rings of xylem alternating with phloem, which show frequent anastomoses. After a period of primary growth and the formation of first (normal) ring of vascular cambium, further successive rings are initiated outside this cambium. The second ring of cambium originates from the pericycle parenchyma located between the proto-phloem, and the pericycle fibres. Each cambium produces centripetally secondary xylem and centrifugally secondary phloem. Differentiation of xylem precedes that of phloem and the first elements formed are always xylem fibres. Structurally, the vascular cylinder is composed by successive rings of secondary xylem and phloem. These rings are separated by wide bands of conjunctive parenchyma tissue. Presence of collateral vascular bundles with irregular orientation is observed in the region of anastomoses of two or more bands of conjunctive tissue. These bundles are surrounded by isodiametric, lignified and thick-walled cells. In some of the cambial rings, occurrence of polycentric rays was also noticed; these rays are tall, and characterized by the presence of meristematic regions that differentiated into thick-walled elements of secondary xylem. Origin and development of the successive cambia and the structure of xylem are discussed.

Cogasification of solid fuels

High efficiency gas turbine based systems, utility deregulation and more stringent environmental regulations strongly favor the use of natural gas over coal and other solid fuels in new electricity generators. Solid fuels could continue to compete, however, if a low cost gasifier fed by low cost feedstocks can be coupled with a gas turbine system. We examine on-site gasification of coal with other domestic fuels in an indirectly heated gasifier as a strategy to lower the costs of solid fuel systems. The systematics of gaseous pyrolysis yields assembled with the help of thermal measurement data and molecular models suggests blending carbonaceous fuels such as coal, coke or char with oxygenated fuels such as biomass, RDF, MSW, or dried sewage sludge. Such solid fuel blending can, with the help of inexpensive catalysts, achieve an optimum balance of volatiles, heating values and residual char thus reducing the technical demands upon the gasifier. Such simplifications should lower capital and operating costs of the gasifier to the mutual benefit of both solid fuel communities.

Screening for pectinolytic activity of wood-rotting basidiomycetes and characterization of the enzymes

Seventy-five fungal strains from different groups of basidiomycetes, newly isolated from rotten wood, were screened for pectinolytic activity. Despite the fact that basidiomycetes are scarcely referred to as pectinase producers, the polygalacturonase (PG) activity was detected in 76 % of the strains; 16 % with activity higher than 40 nkat/g, 40 % between 13.3 and 40 nkat/g, and 44 % with activity lower than 13.3 nkat/g. The highest productions were obtained among the fungi from order Aphyllophorales, family Polyporaceae. The characterization of the enzymes from the highest PG producers (Lentinus sp., Gloeophyllum striatum, Pycnoporus sanguineus, Schizophyllum commune) showed optimum temperature for catalytic activity at 60-70°C and two peaks of pH optimum (3.5-4.5 and 8.5-9.5). The enzymes exhibited high pH stability (3.0-11.0) but after incubation at 40°C for 1 h their activity dropped by 18-73 %.

Remarks on orthotropic elastic models applied to wood

Wood is generally considered an anisotropic material. In terms of engineering elastic models, wood is usually treated as an orthotropic material. This paper presents an analysis of two principal anisotropic elastic models that are usually applied to wood. The first one, the linear orthotropic model, where the material axes L (Longitudinal), R(radial) and T(tangential) are coincident with the Cartesian axes (x, y, z), is more accepted as wood elastic model. The other one, the cylindrical orthotropic model is more adequate of the growth caracteristics of wood but more mathematically complex to be adopted in practical terms. Specifically due to its importance in wood elastic parameters, this paper deals with the fiber orientation influence in these models through adequate transformation of coordinates. As a final result, some examples of the linear model, which show the variation of elastic moduli, i.e., Young's modulus and shear modulus, with fiber orientation are presented.

Actual Brazilian habitations in wood: A technology in development or a question of fashion?

Over the past few years there have significantly been increased the articles that approach the constructions in wood or with structure in wood in the specialized Brazilian magazines. This increase brings up indications that the incorporated values to these habitations are modifying, however it is not so simple to conclude that these issues can be associated to the development of incorporated technologies to the constructive system. The work presents, firstly, a survey performed in these publications that had the objective to verify which the constructive systems in wood is being more executed, under which cultural and technician standards. From that survey it was performed a study of the habitations constructed in mixing system whose structures are timbers and walls in masonry. The aesthetic and cultural questions involved are argued considering mainly that these habitations belong to a social class whose purchasing power increased.

The wood for the civil engineering: A proposal of distance education

The majority of the Brazilian schools of Civil Engineering have taught the subject works with wood in the traditional only by disciplines of Metallic Structures and Wood at a topic in the content of the program on disciplines at the Materials of Civil Construction. To extend of the wood studies is being made possible that all the pupils have a wider understanding of this material and its adapted use is the goal of the proposal, that by the means of the education modality e-learning, disclosing the first one: Module I - Introduction to the Study of the Wood. This methodology tries to use the theoretical beddings in projects that are related to the pupil daily tasks and its practical professional. The article presents the theoretical bases of the conception proposal and its structure, and at the conclusions, the problems found during its application are displayed. Basically, the methodology considers that the professor and the pupil must share the learning, and adopt it as main in the interdisciplinary.