Low-cost PWM speed controller for an electric mini-baja type vehicle

This paperwork presents a Pulse Width Modulation (PWM) speed controller for an electric mini-baja-type car. A battery-fed 1-kW three-phase induction motor provides the electric vehicle traction. The open-loop speed control is implemented with an equal voltage/frequency ratio, in order to maintain a constant amount of torque on all velocities. The PWM is implemented by a low-cost 8-bit microcontroller provided with optimized ROM charts for distinct speed value implementations, synchronized transition between different charts and reduced odd harmonics generation. This technique was implemented using a single passenger mini-baja vehicle, and the essays have shown that its application resulted on reduced current consumption, besides eliminating mechanical parts. Copyright © 2007 by ABCM.

An investigation into the loss of the Brazilian space programme's launch vehicle VLS-1 V03

There has been a rapid increase in the complexity and integration of many safety-critical systems. In consequence, it is becoming increasingly difficult to identify the causes of incidents and accidents back through the complex interactions that lead to an adverse event. At the same time, there is a growing appreciation of the need to consider a broad range of contextual factors in the aftermath of any mishap. A number of regulators, operators and research teams have responded to these developments by proposing novel techniques to support the analysis of complex, safety-critical incidents. It is important to illustrate these different approaches by applying them to a number of common case studies. The following pages, therefore, show how STAMP and AcciMap might support the Serviço Público Federal investigation into the explosion and fire of the Brazilian launch vehicle VLS-1 VO3. © 2006 Elsevier Ltd. All rights reserved.

Power losses analysis and cooling system design of three topologies of multilevel inverters

This paper presents the comparison of three topologies of multilevel inverters applied to drive an induction motor of 500 kVA/4.16 kV. The multilevel inverters analyzed are: a neutral point clamped inverter, a symmetrical cascaded multilevel inverter and a hybrid asymmetrical cascaded multilevel inverter. The performance indexes used in the comparison are total harmonic distortion, first order distortion factor, semiconductors power losses distribution and heat-sink volume. The comparison is developed with the purpose of finding the efficiency and the heat-sink volume where the three systems present the same output filter. ©2008 IEEE.

Modeling of a MIT for the application of a frequency inverter of the electric vehicle

Nowadays, drives that use a combination of induction motors and frequency inverters are very common, a fact due to the financial practicality and viability in purchasing and operating that system. This system modeling and simulation becomes important when it wants to evaluate the performance, to calculate and correct parameters, and it has a fundamental role in functionality and viability analysis for application of new configurations and technologies. This work is about to elaborate a simple induction motor model based in the torque versus speed characteristic, using the linearization method for application in a specific operation range to be controlled by a frequency inverter. © 2011 Springer-Verlag Berlin Heidelberg.

Straightforward systematic approach for fuel efficiency and emissions assessment in automotive systems

At this time, each major automotive market bares its own standards and test procedures to regulate the vehicle green house gases emissions and, thus, fuel consumption. Hence, much are the ways to evaluate the overall efficiency of motor vehicles. The majority of such standards rely on dynamometer cycle tests that appraise only the vehicle as a whole, but fail to assess emissions for each component or sub-system. Once the amount of work generated by the power source of an ICE vehicle to overcome the driving resistance forces is proportional to the energy contained in the required amount of fuel, the power path of the vehicle can be straightforwardly modeled as a set of mechanical systems, and each sub-system evaluated for its share on the total fuel consumption and green house gases emission. This procedure enables the estimation of efficiency gains on the system due to improvement of particular elements on the vehicle's driveline. In this work a simple systematic mechanical model of an arbitrary smallsized hatch back was assembled and total required energy calculated for different regulatory cycles. All the modeling details of the energy balance throughout the system are presented. Afterward, each subsystem was investigated for its role on the fuel consumption and the generated emission quantified. Furthermore, the application of the modeling technique for different sets of sub-systems was introduced. Copyright © 2011 SAE International.

Mobile application as a tool for urban traffic data collection and generation to advanced traveler information systems using Wi-Fi networks available in urban centers

This paper presents an Advanced Traveler Information System (ATIS) developed on Android platform, which is open source and free. The developed application has as its main objective the free use of a Vehicle-to- Infrastructure (V2I) communication through the wireless network access points available in urban centers. In addition to providing the necessary information for an Intelligent Transportation System (ITS) to a central server, the application also receives the traffic data close to the vehicle. Once obtained this traffic information, the application displays them to the driver in a clear and efficient way, allowing the user to make decisions about his route in real time. The application was tested in a real environment and the results are presented in the article. In conclusion we present the benefits of this application. © 2012 IEEE.

Improvement and evaluation of the MS2SV for mixed systems design described in abstraction high level

This paper presents an important improvement of the MS2SV tool. The MS2SV performs the translation of mixed systems developed in MATLAB / Simulink for a structural or behavioral description in VHDL-AMS. Previously, the MS2SV translated only models of the LIB MS2SV library. This improvement allows designer to create your own library to translation. As case study was used a rudder controller employed in an unmanned aerial vehicle. For comparison with the original model the VHDL-AMS code obtained by the translation was simulated in SystemVision environment. The results proved the efficiency of the tool using the translation improvement proposed in this paper.

Nasal administration of liquid crystal precursor mucoadhesive vehicle as an alternative antiretroviral therapy

The purpose of this study was to develop a mucoadhesive stimuli-sensitive drug delivery system for nasal administration of zidovudine (AZT). The system was prepared by formulating a low viscosity precursor of a liquid crystal phase, taking advantage of its lyotropic phase behavior. Flow rheology measurements showed that the formulation composed of PPG-5-CETETH-20, oleic acid and water (55, 30, 15% w/w), denominated P, has Newtonian flow behavior. Polarized light microscopy (PLM) revealed that formulation P is isotropic, whereas its 1:1 (w/w) dilution with artificial nasal mucus (ANM) changed the system to an anisotropic lamellar phase (PD). Oscillatory frequency sweep analysis showed that PD has a high storage modulus (G′) at nasal temperatures. Measurement of the mucoadhesive force against excised porcine nasal mucosa or a mucin disk proved that the transition to the lamellar phase tripled the work of mucoadhesion. Ex vivo permeation studies across porcine nasal mucosa exhibited an 18-fold rise in the permeability of AZT from the formulation. The Weibull mathematical model suggested that the AZT is released by Fickian diffusion mechanisms. Hence, the physicochemical characterization, combined with ex vivo studies, revealed that the PPG-5-CETETH-20, oleic acid, and water formulation could form a mucoadhesive matrix in contact with nasal mucus that promoted nasal absorption of the AZT. For an in vivo assessment, the plasma concentrations of AZT in rats were determined by HPLC method following intravenous and intranasal administration of AZT-loaded P formulation (PA) and AZT solution, respectively, at a dose of 8 mg/kg. The intranasal administration of PA resulted in a fast absorption process (Tmax = 6.7 min). Therefore, a liquid crystal precursor formulation administered by the nasal route might represent a promising novel tool for the systemic delivery of AZT and other antiretroviral drugs. In the present study, the uptake of AZT absorption in the nasal mucosa was demonstrated, providing new foundations for clinical trials in patients with AIDS. © 2012 Elsevier B.V. All rights reserved.

Effective synchronization of a class of chua's chaotic systems using an exponential feedback coupling

A robust exponential function based controller is designed to synchronize effectively a given class of Chua's chaotic systems. The stability of the drive-response systems framework is proved through the Lyapunov stability theory. Computer simulations are given to illustrate and verify the method. © 2013 Patrick Louodop et al.

ATP in the locus coeruleus as a modulator of cardiorespiratory control in unanaesthetized male rats

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Otimização da estrutura metalica para um carro alegórico

Carnival is a unique opportunity for the associations demonstrate the community’s annual work and the float is a major component of this celebration, responsible for pitch the samba using allegories and carry important figures. The excess weight of the floats which are mostly manufactured from truck and bus structures requires larger amount of people to push the vehicle in addition to increased efforts on the steering systems, suspension and wheels, raising the probability of breakage and loss of one year work. The objective of this study is to use the concepts of strength of materials combined with computer simulation to obtain a structure that has the lowest possible weight without compromising the safety of transported components and that is also easy to manufacture, drive and store