Influence of Implant Drill Materials on Wear, Deformation, and Roughness After Repeated Drilling and Sterilization

Purpose:The aim of this study was to evaluate deformation, roughness, and mass loss of stainless steel, diamond-like carbon (DLC)-coated and zirconia drills after multiple osteotomies with sterilization procedures.Materials and Methods:Drilling procedures were performed using stainless steel (G1), DLC-coated (G2), and zirconia (G3) drills. All groups were divided in subgroups 1, 2, 3, 4, and 5, corresponded to drills used 0, 10, 20, 30, and 40 times, respectively.Results:No significant differences in mass and roughness were detected among all groups and subgroups. In SEM images, all groups revealed signs of wear while coating delamination was detected in G2. Drills from G1 displayed more irregular surface, whereas cutting edges were more regular in G3.Conclusion:Zirconia drills presented more regular surfaces whereas stainless steel drills revealed more severe signs of wear. Further studies must be performed to evaluate the putative influence of these findings in heat generation.

Evaluation of Bone Heating, Drill Deformation, and Drill Roughness After Implant Osteotomy: Guided Surgery and Classic Drilling Procedure

Purpose: This study evaluated and compared bone heating, drill deformation, and drill roughness after several implant osteotomies in the guided surgery technique and the classic drilling procedure. Materials and Methods: The tibias of 20 rabbits were used. The animals were divided into a guided surgery group (GG) and a control group (CG); subgroups were then designated (G0, G1, G2, G3, and G4, corresponding to drills used 0, 10, 20, 30 and 40 times, respectively). Each animal received 10 sequential osteotomies (5 in each tibia) with each technique. Thermal changes were quantified, drill roughness was measured, and the drills were subjected to scanning electron microscopy. Results: Bone temperature generated by drilling was significantly higher in the GG than in the CG. Drill deformation in the GG and CG increased with drill use, and in the CG a significant difference between GO and groups G3 and G4 was observed. In the GG, a significant difference between GO and all other groups was found. For GG versus CG, a significant difference was found in the 40th osteotomy. Drill roughness in both groups was progressive in accordance with increased use, but there was no statistically significant difference between subgroups or between GG and CG overall. Conclusion: During preparation of implant osteotomies, the guided surgery technique generated a higher bone temperature and deformed drills more than the classic drilling procedure. The increase in tissue temperature was directly proportional to the number of times drills were used, but neither technique generated critical necrosis-inducing temperatures. Drill deformation was directly proportional to the number of times the drills were used. The roughness of the drills was directly proportional to the number of reuses in both groups but tended to be higher in the GG group.

Effect of Er:YAG laser and diamond drill on hybrid layer morphology obtained with self-etch adhesive: analysis by SEM and confocal laser scanning microscopy (CLSM)

This study aimed to evaluate the effect of Er:YAG (L) and diamond drills (DD) on: 1) the microshear bond strength (MPa); 2) the adhesive interface of two-step (TS) – Adper Scotchbond Multipurpose and one-step (OS) adhesives – Adper EasyOne, both from 3M ESPE. Material and methods: According to the preparation condition and adhesives, the samples were divided into four groups: DD_TS (control); DD_OS; L_TS and L_OS. 60 bovine incisors were randomly divided into experimental and groups: 40 for microshear bond strength (n = 10) and 20 for the adhesive interface morphology [6 to measure the thickness of the hybrid layer (HL) and length of tags (t) by CLSM (n = 3); 12 to the adhesive interface morphology by SEM (n = 3) and 2 to illustrate the effect of the instruments on dentine by SEM (n = 1)]. To conduct the microshear bond strength test, four cylinders (0.7 mm in diameter and 1 mm in height with area of adhesion of 0.38 mm) were constructed with resin composite (Filtek Z350 XT – 3M ESPE) on each dentin surface treated by either L or DD and after adhesives application. Microshear bond strength was performed in universal testing machine (EMIC 2000) with load cell of 500 kgf and a crosshead speed of 0.5 mm / min. Adhesive interface was characterized by thickness of hybrid layer (HL) and length of tags (t) in nm, with the aid of UTHSCSA ImageTool software. Results: Microshear bond strength values were: L_TS 34.10 ± 19.07, DD_TS 24.26 ± 9.35, L_OS 33.18 ± 12.46, DD_OS 21.24 ± 13.96. Two-way ANOVA resulted in statistically significant differences only for instruments (p = 0.047). Mann-Whitney identified the instruments which determined significant differences for HL thickness and tag length (t). Concerning to the adhesive types, these differences were only observed for (t). Conclusion: It can be concluded that 1) laser Er:YAG results in higher microshear bond strength values regardless of the adhesive system (TS and OS); 2) the tags did not significant affect the microshear bond strength; 3) the adhesive interface was affected by both the instruments for cavity preparation and the type of adhesive system used.

Estudo histomorfométrico do processo de cicatrização óssea em defeitos cirúrgicos de camanho crítico em calvárias de ratos preenchidos com polímero de mamona

Objectives: The aim of this study was to evaluate the behavior of the polymer histomorphometrically castor during the healing process of defects of critical size calvarial preparations in rats. Materials and Methods: Twenty animals underwent a surgical procedure that was to be held in the calvaria of each animal a critical defect of 8 mm in diameter with a drill trephine. The rats were divided into two groups according to the following procedures: group C received no treatment and the bone defect site was filled with blood clot, group M, the bone defect was filled with castor oil polymer particles. The animals were sacrificed 180 days after the surgical procedures. After routine laboratory procedures the specimens were subjected to analysis histomorphometric. Results: In groups C the newly formed bone tissue was well developed, with adjacent areas of osteoid matrix rich in osteoblasts, and restricted to the vicinity of the edges of the defect. In animals of group M was observed newly formed lamellar bone tissue restricted to the vicinity of the defect edges and particles of polymer Castor distributed throughout the defect. There was a higher percentage of newly formed bone area was statistically significant in group C compared to animals in group M. Conclusions: Within the limits of this study can conclude that the castor oil polymer is biocompatible and had kept the area during the healing of critical size defects in surgically prepared rat calvariae.

Estudo histomorfométrico do processo de cicatrização óssea em defeitos cirúrgicos de tamanho crítico em calvárias de ratos preenchidos com polímero de mamona

Objectives: The aim of this study was to evaluate the behavior of the polymer histomorphometrically castor during the healing process of defects of critical size calvarial preparations in rats. Materials and Methods: Twenty animals underwent a surgical procedure that was to be held in the calvaria of each animal a critical defect of 8 mm in diameter with a drill trephine. The rats were divided into two groups according to the following procedures: group C received no treatment and the bone defect site was filled with blood clot, group M, the bone defect was filled with castor oil polymer particles. The animals were sacrificed 180 days after the surgical procedures. After routine laboratory procedures the specimens were subjected to analysis histomorphometric. Results: In groups C the newly formed bone tissue was well developed, with adjacent areas of osteoid matrix rich in osteoblasts, and restricted to the vicinity of the edges of the defect. In animals of group M was observed newly formed lamellar bone tissue restricted to the vicinity of the defect edges and particles of polymer Castor distributed throughout the defect. There was a higher percentage of newly formed bone area was statistically significant in group C compared to animals in group M. Conclusions: Within the limits of this study can conclude that the castor oil polymer is biocompatible and had kept the area during the healing of critical size defects in surgically prepared rat calvariae

Avaliação da incorporação de enxerto osseo homogeno fresco congelado em humanos: análise histologica e imuno-histoquímica

Allogeneic, fresh-frozen bone has been used in order to replace bone autografts. However, its osteoinduction and osteoconduction properties are not well-defined in the scientific literature. This work aimed to evaluate samples of homogenous bone grafts in humans by qualitative histological and immunohistochemical analysis. For this, ten pre-selected patients underwent surgical augmentation of bone defects. The homogenous fresh frozen block bone graft was stabilized and fixed by bicortical screws. After six months, the reopening procedure was performed for installation of osseointegrated implants. At this time surgical bone graft samples were removed by means of drill trephine. The samples were fixed in 10% formalin, processed with decalcified paraffin, and stained with hematoxylin and eosin. Immunohistochemistry was performed for the expression of Caspase 3 enzyme. The slides were brought to light microscopy for qualitative histology and immunohistochemistry. The results showed non-vital bone tissue, with few areas of deposition of new bone formation on the amorphous matrix, presence of chronic inflammatory infiltrate with areas of osteomyelitis, and expressive immunolabeling of Caspase 3. Given the methods employed and the results it was concluded that the allograft fresh-frozen block is not incorporated into the recipient bed after a healing period of six months.

Evaluation of the Integrity of Horse Hoof Dermal and Epidermal Tissues Collected by Dorsal Transmural Access

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Semeadura direta de milho com dois tipos de sulcadores de adubo, em nível e no sentido do declive do terreno

O presente estudo teve como objetivo avaliar parâmetros operacionais de um conjunto mecanizado envolvendo trator e semeadora, assim como o rendimento da cultura do milho semeada nas diferentes configurações das máquinas e combinações com o ambiente de produção. Os tratamentos consistiram de tipos de sulcadores (discos duplos e hastes), os quais foram avaliados em experimentos em que a operação de semeadura direta do milho foi efetuada transversalmente ao declive (em nível) e em aclive e declive. A semeadura contra o declive e o uso de haste sulcadora implicaram maior demanda de esforço de tração, patinagem do trator e consumo de combustível por área trabalhada e não influenciaram o volume de solo mobilizado, a população de plantas e a produtividade de grãos do milho, em relação à operação realizada em declive e uso de sulcador de discos duplos, respectivamente. A utilização de sulcador do tipo haste resultou em menor número de plantas acamadas e quebradas, em relação ao uso de discos duplos, independentemente do sentido da operação. A principal diferença entre semear em nível ou em declive é a formação de sulcos orientados no sentido do terreno, pela ação de sulcadores do tipo haste e elevada patinagem dos rodados do trator, já que o consumo de combustível por área trabalhada e capacidade operacional não foram afetados por aquelas variáveis.

Análise espacial da distribuição longitudinal de sementes de milho em uma semeadora-adubadora de precisão

In the operation of sowing with planter numerous factors interfere with the establishment of the plant stand, among them, the longitudinal distribution of seeds depending on the displacement speed can significantly affect crop productivity.The present study aimed the evaluation of longitudinal distribution of maize seeds in two different speeds of dislocation of a precision grain drill, through classical and geostatistics. A regular grid sample, totalizing 100 points in each area, was built with 10-meter distance among the points. Each sample point comprised 3.6m(2) (1.8 x 2.0) where the percentage of acceptable, double and fail spacing among the plants was measured after sowing at 4.58 and 5.94 km h(-1) speed of dislocation. Classical and geostatistics were used for data analyses. The percentage of acceptable and failed spacing has shown significant difference between 4.58 and 5.94 km h(-1) speed. The results has shown absence of spatial dependence regarding the percentage of the studied spacing (acceptable, fail and double) at both speeds, showing that studies and statistical inferences can occur based on parameters of classical statistics for distances higher than the shortest one used in the sampling.

Desempenho operacional de uma semeadora-adubadora de precisão, em função do preparo do solo e do manejo da cobertura de inverno

Avaliou-se o desempenho operacional de campo de uma semeadora-adubadora de precisão, equipada com seis linhas espaçadas de 550 mm, em um solo muito argiloso, classificado como Nitossolo Vermelho Distrófico Latossólico, na semeadura do feijoeiro (Phaseolus vulgaris L.). Os tratamentos consistiram de três métodos de preparo do solo: a) convencional (uma aração com arado de discos e duas gradagens niveladoras); b) escarificação (uma passagem de escarificador conjugado com rolo destorroador), e c) semeadura direta. Esses procedimentos foram combinados com quatro condições de cobertura do solo no inverno (consórcio aveia-preta + nabo forrageiro manejados com rolo-faca, triturador de palhas, herbicida e solo em pousio). Os métodos de preparo do solo e os manejos da cobertura foram repetidos por três anos consecutivos. Os valores de força e pico de força de tração na barra, patinagem dos rodados motrizes e consumo de combustível foram maiores no preparo com escarificador em relação aos obtidos no preparo convencional e na semeadura direta. A capacidade de campo efetiva foi maior na semeadura direta em relação aos outros tratamentos. Os manejos efetuados nas coberturas vegetais e o solo mantido em pousio não influenciaram em nenhuma das variáveis.

Fertilizer distribution mechanisms and side dress nitrogen fertilization in upland rice under no-tillage system

Algumas culturas têm pouca adaptação ao sistema plantio direto (SPD), em vista da alta compactação da camada superficial do solo. Nesse caso, o mecanismo utilizado na semeadora para a abertura dos sulcos para deposição do fertilizante pode ter grande importância no sentido de facilitar a penetração das raízes. Avaliouse a influência do mecanismo de distribuição de fertilizante e da adubação nitrogenada na cultura do arroz de terras altas (Oryza sativa) no sistema plantio direto. O experimento foi conduzido nos anos agrícolas 2001/2002 e 2002/2003, em Botucatu-SP, Brasil. O delineamento experimental foi em blocos casualizados, com parcelas subdivididas e quatro repetições. As parcelas foram constituídas por dois mecanismos de distribuição de fertilizantes (haste sulcadora e disco duplo). Nas subparcelas, quatro níveis de N foram aplicados em cobertura (0, 40, 80 e 120 kg ha-1). Avaliou-se a profundidade de abertura do sulco e de deposição das sementes, a população de plantas, a altura de plantas, o número de colmos e de panículas m-2, o número total de espiguetas por panícula, a fertilidade das espiguetas, a massa de 1.000 grãos, a matéria seca da parte aérea, a produtividade e o teor de N na folha bandeira. O sucesso no estabelecimento da cultura do arroz de terras altas no SPD nas regiões de inverno seco do Brasil está diretamente ligado ao mecanismo de distribuição das semeadoras-adubadoras. A haste sulcadora promoveu maior profundidade de deposição de sementes, conseqüentemente reduzindo o estande, o número de panículas por área e a produtividade. A aplicação de N em cobertura no arroz de terras altas em SPD proporciona maiores produtividades quando a semeadura é realizada com mecanismo de disco duplo.

Evaluation of Centrifuged Bone Marrow on Bone Regeneration Around Implants in Rabbit Tibia

Objective: To evaluate the bone regeneration of cervical defects produced around titanium implants filled with blood clot and filled with centrifuged bone marrow (CBM) by means of histomorphometric analysis.Materials and Methods: Twelve rabbits received 2 titanium implants in each right tibia, with the upper cortical prepared with a 5-mm drill and the lower cortex with a 3-mm-diameter drill. Euthanasia was performed to allow analysis at 7, 21, and 60 days after operation. The samples were embedded in light curing resin, cut and stained with alizarin red and Stevenel blue for a histomorphometric analysis of the bone-to-implant contact (BIC) and the bone area around implant (BA). The values obtained were statistically analyzed using the nonparametric Kruskal-Wallis test (P = 0.05).Results: At 60 days postoperation, the groups had their cervical defects completely filled by neo-formed bone tissue. There was no statistically significant difference between the groups regarding BIC and BA during the analyzed periods.Conclusion: There was no difference in the bone repair of periimplant cervical defects with or without the use of CBM. (Implant Dent 2012;21:481-485)

Bone regeneration in surgically created defects filled with autogenous bone: an epifluorescence microscopy analysis in rats

Although the search for the ideal bone substitute has been the focus of a large number of studies, autogenous bone is still the gold standard for the filling of defects caused by pathologies and traumas, and mainly, for alveolar ridge reconstruction, allowing the titanium implants installation. Objectives: The aim of this study was to evaluate the dynamics of autogenous bone graft incorporation process to surgically created defects in rat calvaria, using epifluorescence microscopy. Material and methods: Five adult male rats weighing 200-300 g were used. The animals received two 5-mm-diameter bone defects bilaterally in each parietal bone with a trephine bur under general anesthesia. Two groups of defects were formed: a control group (n=5), in which the defects were filled with blood clot, and a graft group (n=5), in which the defects were filled with autogenous bone block, removed from the contralateral defect. The fluorochromes calcein and alizarin were applied at the 7th and 30th postoperative days, respectively. The animals were killed at 35 days. Results: The mineralization process was more intense in the graft group (32.09%) and occurred mainly between 7 and 30 days, the period labeled by calcein (24.66%). Conclusions: The fluorochromes showed to be appropriate to label mineralization areas. The interfacial areas between fluorochrome labels are important sources of information about the bone regeneration dynamics.

Histologic evaluation of the use of membrane, bone graft, and MTA in apical surgery

The aim of this study was to evaluate the periapical healing after the use of membrane, bone graft, and mineral trioxide aggregate (MTA) in apical surgery of dogs' teeth. Apical lesions were induced in 48 roots of 6 dogs after coronal access and pulpal removal. Apical surgery consisted of osteotomy with trephine bur for the standardization of the critical surgical cavities, followed by apicoectomy, curettage, preparation of the root-end cavities with the aid of the ultrasonic device, and retrofilling with MTA. The surgical sites were divided into: group 1-filled with blood; group 2-filled with blood and recovered with membrane; group 3-filled with bone graft; and group 4-filled with bone graft and recovered with membrane. The results showed that the inflammatory infiltrate, the periapical healing process, and the behavior of MTA was the same in all groups, including the mineralization stimulation. It was concluded that the use of membranes and bone graft materials isolated or associated in apical surgery did not alter the periapical healing process after the root-end filling with MTA. (Oral Surg Oral Med Oral Pathol Oral Radiol Endod 2010; 109: 309-314)

Use of bovine bone graft and bone membrane in defects surgically created in the cranial vault of rabbits. Histologic comparative analysis

Purpose: This study was proposed to analyze histologically the process of repairing bone defects created surgically in the cranial vaults of rabbits. Materials and Methods: Thirty adult male rabbits (Oryctolagus cunilicus) received, under general anesthesia, bilateral parietal osteotomies by means of a 6mm-diameter trephine. The bony defects were divided into 4 groups. In group 1 the defect did not receive any treatment; in group 2 the defect was filled with lyophilized bovine bone (Biograft); in group 3 it was filled with bovine bone and covered with a bone matrix membrane (Bioplate); in group 4 it was covered with a bone matrix membrane. Animals were sacrificed in 3 equal groups at 15, 30, and 60 days. The specimens were subjected to routine laboratory procedures to evaluate the degree of bone repair. Results: After 60 days, new bone formation in group 2 was not satisfactory when compared to that of group 3. Large amounts of new bone formation in maturation were seen in group 3. In the defects covered with a membrane the results were similar to those of group 1 (ie, the cavity was filled with fibrous connective tissue). The implanted bone and membranes were totally resorbed. Discussion and Conclusions: the use of a membrane served as a barrier against the migration of cells from the adjacent tissue and the bone graft/membrane preserved the cavity space, resulting in an enhanced osteogenic effect.