Use of scrap tire rubber in place of SBS in modified asphalt as an environmentally correct alternative for Brazil

Reusing scrap tires has become a worldwide challenge, especially due to the great difficulty in finding ecologically and economically feasible ways to dispose of them. This has led to the creation of specific programs and legislation for reusing scrap tires. Research has shown that a certain percentage of scrap tire rubber can be added to asphalt compositions, and this has become a worldwide practice. This paper describes the properties of four asphalt compositions modified with scrap tire rubber (STR) prepared in the laboratory. These properties are then compared with those of asphalt modified with styrene butadiene styrene (SBS), a synthetic polymer and one of the most common modifiers, to verify the feasibility of using scrap tire rubber as a substitute for SBS. The scope of this study does not include an analysis of how STR affects end-of-life asphalt. The main findings indicate that STR is a potential substitute of SBS in paving material, and although it does not meet some of the standard specifications when compared with SBS, these issues can be overcome by proper care during storage and transportation. The substitution of SBS by STR also showed the potential for about 10% in expenditure savings. (C) 2012 Elsevier Ltd. All rights reserved.

Investigation on Surface Finishing of Components Ground with Lapping Kinematics: Lapgrinding Process

Over the last three decades, researchers have responded to the demands of industry to manufacture mechanical components with geometrical tolerance, dimensional tolerance, and surface finishing in nanometer levels. The new lapgrinding process developed in Brazil utilizes lapping kinematics and a flat grinding wheel dressed with a single-point diamond dresser in agreement with overlap factor (U(d)) theory. In the present work, the influences of different U(d) values on dressing (U(d) = 1, 3 e 5) and grain size of the grinding wheel made of silicon carbide (SiC = 800, 600 e 300 mesh) are analyzed on surface finishing of stainless steel AISI 420 flat workpieces submitted to the lapgrinding process. The best results, obtained after 10 minutes of machining, were: average surface roughness (Ra) 1.92 nm; 1.19 mu m flatness deviation of 25.4 mm diameter workpieces and mirrored surface finishing. Given the surface quality achieved, the lapgrinding process can be included among the ultra-precision finishing processes and, depending on the application, the steps of lapping followed by polishing can be replaced by the proposed abrasive process.

Absence of gluonic components in axial and tensor mesons

A quarkonium-gluonium mixing scheme previously developed to describe the characteristic of the pseudoscalar mesons is applied to axial and tensor mesons. The parameters of the model are determined by fitting the eigenvalues of a mass matrix. The corresponding eigenvectors give the proportion of light quarks, strange quarks and glueball in each meson. However, the predictions of the model for the branching ratios and electromagnetic decays are incompatible with the experimental results. These results suggest the absence of gluonic components in the states of axial and tensor isosinglet mesons analyzed here.

Waveshapes of continuing currents and properties of M-components in natural positive cloud-to-ground lightning

This work analyses the waveshapes of continuing currents and parameters of M-components in positive cloud-to-ground (CG) flashes through high-speed GPS synchronized videos. The dataset is composed of only long continuing currents (with duration longer than 40 ms) and was selected from more than 800 flashes recorded in Sao Jose dos Campos (45.864 degrees W, 23.215 degrees S) and Uruguaiana (29.806 degrees W, 57.005 degrees S) in Southeast and South of Brazil, respectively, during 2003 to 2007 summers. The videos are compared with data obtained by the Brazilian Lightning Location System (BrasilDAT) in order to determine the polarity of each flash and select only positive cases. There are only two studies of waveshapes of continuing currents in the literature. One is based on direct current measurements of triggered lightning, in which four different types of waveshapes were observed; and the other is based on measurements of luminosity variations in high-speed videos of CG negative lightning, in which besides the four types above mentioned two additional types were observed. The present work is an extension of the latter, using the same method but now applied to obtain the waveshapes of positive CG lightning. As far as the authors know, this is the first report on M-components in positive continuing currents. We also have used the luminosity-versus-time graphs to observe their occurrence and measure some parameters (duration, elapsed time and time between two successive M-components), whose statistics are presented and compared in detail to the data for negative flashes. We have plotted a histogram of the M-components elapsed time over the total duration of the continuing current for positive flashes, which presented an exponential decay (correlation coefficient: 0.83), similar to what has been observed for negative flashes. (C) 2008 Elsevier B.V. All rights reserved.

A metallurgical study of aluminium alloys used as aircraft components

The effects of heat treatment on morphologies and microstructures of Al 2024 and Al 7050 alloys, used as aircraft components, were studied by metallographic techniques. Light microscopy (LM) and quantitative image analysis were used to characterize the precipitate dispersion and morphology for these alloys. The application of the scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) combined techniques for studying these multiphase systems makes it possible to distinguish and quantify the different phases in the surface structure. Xray diffraction also permitted a qualitative comparison of the structures before and after heat treatments.

Time-dependent alterations of soluble and cellular components in human milk

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Brazilian natural dietary components (annatto, propolis and mushrooms) protecting against mutation and cancer

Considering the high number of new cancer cases in Brazil (approximately 470 000 cases in 2005) and the remarkable differences in the incidence of this disease around the world, the development of chemopreventive strategies using foods widely consumed would have a huge impact, both medically and economically. This review summarizes some of our studies conducted to verify the anti-mutagenic and anti-carcinogenic potential of some Brazilian natural dietary constituents (annatto, mushrooms, and propolis). Overall data have shown a clear role for these compounds in preventing mutation and specific preneoplastic lesions. Taken together, these agents indicate a favorable side-effect profile and may prove to be a promising alternative for cancer prevention strategies, although more investigation is needed to fully explore this issue.

Dietary components may prevent mutation-related diseases in humans

Since it is not always possible to reduce human exposure to mutagens, attempts have been directed to identify potential antimutagens and anticarcinogens for use in protecting the population against environmental disease. The purpose of this paper is to provide the reader with information about the antimutagenic and anticarcinogenic potentials of some dietary constituents and foods widely consumed in Brazil, and to reinforce diet as a key factor in determining genomic stability and preventing human diseases. In this report, we have summarized data that show interactive effects between some dietary components and specific chemical mutagens or carcinogens using in vitro and in vivo short- or medium-term assays. The summary indicates that certain dietary compounds may be useful agents for disease prevention. (C) 2003 Elsevier B.V. All rights reserved.

Expression of cell cycle regulatory proteins in epithelial components of dental follicles

Dental follicle is a component of tooth germs, which remain adjacent to the crown of unerupted or impacted teeth. Under the influence of pathologic changes, however, dental follicles that possess reduced epithelium can proliferate into stratified squamous epithelium as far as originate dental cysts. In order to clarify the role of apoptosis and cellular proliferation herein, expression of p53 and PCNA was examined in epithelial components of dental follicles associated with impacted third molars by means of immunohistochemistry. A total of 40 cases was included in this study being 22 cases with reduced epithelium and 18 cases with stratified epithelium. Expression of p53 expression was weak or not detected in dental follicles with reduced and stratified squamous epithelium. By contrast, PCNA positive cells were evidenced in basal and supra basal layers of the stratified squamous epithelium and in reduced epithelium of dental follicles, but without any significant statistically differences between them (P > 0.05). In conclusion, these data suggest that dental follicles possess proliferative activity as depicted by PCNA-positive nuclei in some epithelial cells. However, the biological behavior of dental follicles during the late stage of dental eruptive process may not be associated with deregulation of death and/or cell proliferation.

Metabolic syndrome and dietary components are associated with coronary artery disease risk score in free-living adults: a cross-sectional study

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Mapping quantitative trait loci in Gallus gallus using principal components

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Vasectomy effect on canine seminal plasma biochemical components and their correlation with seminal parameters

Three semen samples were collected at 48 It intervals from 20 mature research dogs previously conditioned to manual semen collection. Vasectomy was performed in all dogs, and 15 days after surgery, another three ejaculates were similarly collected. The semen was evaluated, and centrifuged to obtain seminal plasma for measurement of pH, and concentrations of total proteins (TP), total chlorides (Cl), calcium (Ca), potassium (K), and sodium (Na). The seminal plasma protein profile was evaluated by SDS-PAGE; molecular weights and the integrated optical density (IOD) of each band were estimated. There was a negative correlation between K concentration and progressive motility (r = -0.49, P = 0.027), sperm vigor (r = -0.60, P = 0.0053), and plasma integrity, evaluated by both the hypo-osmotic swelling test (r = -0.50, P = 0.026) and a fluorescent stain (r = -0.45, P = 0.046). Positive correlations between Na and K pre- and post-vasectomy (r = 0.88, P < 0.001; r = 0.56, P < 0.01, respectively) were verified. There were a total of 37 bands pre-vasectomy and 35 post-vasectomy (range, 100.6-3.6 kDa). Bands B9 and B13 (42.6 and 29.2 kDa) were not present post-vasectomy. The IOD of band B3 (73.5 kDa) was higher (P 0.03) pre-vasectomy, compared to post-vasectomy; conversely, the IODs of bands B29 and B37 (7.8 and 3.6 kDa) increased (P 0.026 and 0.047). Pre-vasectomy, there was a positive correlation (r = 0.49, P = 0.029) between band B37 band (3.6 kDa) and the Na:K ratio. In conclusion, K appeared to be involved in sperm motility in dogs and could be a tool to evaluate sperm function. The prostate contributed several elements to canine seminal plasma. Vasectomy changed Ca concentrations and the protein profile of the seminal plasma. Further studies must be performed to clarify the function of these elements on the in vivo fertility of dogs. (c) 2006 Elsevier B.V. All rights reserved.

Characterization of S3Pvac Anti-Cysticercosis Vaccine Components: Implications for the Development of an Anti-Cestodiasis Vaccine

Background: Cysticercosis and hydatidosis seriously affect human health and are responsible for considerable economic loss in animal husbandry in non-developed and developed countries. S3Pvac and EG95 are the only field trial-tested vaccine candidates against cysticercosis and hydatidosis, respectively. S3Pvac is composed of three peptides (KETc1, GK1 and KETc12), originally identified in a Taenia crassiceps cDNA library. S3Pvac synthetically and recombinantly expressed is effective against experimentally and naturally acquired cysticercosis.Methodology/ Principal Findings: In this study, the homologous sequences of two of the S3Pvac peptides, GK1 and KETc1, were identified and further characterized in Taenia crassiceps WFU, Taenia solium, Taenia saginata, Echinococcus granulosus and Echinococcus multilocularis. Comparisons of the nucleotide and amino acid sequences coding for KETc1 and GK1 revealed significant homologies in these species. The predicted secondary structure of GK1 is almost identical between the species, while some differences were observed in the C terminal region of KETc1 according to 3D modeling. A KETc1 variant with a deletion of three C-terminal amino acids protected to the same extent against experimental murine cysticercosis as the entire peptide. on the contrary, immunization with the truncated GK1 failed to induce protection. Immunolocalization studies revealed the non stage-specificity of the two S3Pvac epitopes and their persistence in the larval tegument of all species and in Taenia adult tapeworms.Conclusions/ Significance: These results indicate that GK1 and KETc1 may be considered candidates to be included in the formulation of a multivalent and multistage vaccine against these cestodiases because of their enhancing effects on other available vaccine candidates.

Long-term nano-mechanical properties of biomodified dentin-resin interface components

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Skeletal and dental components of Class II correction with the bionator and removable headgear splint appliances

The purpose of this study was to differentiate the dentoalveolar and skeletal effects to better understand orthodontic treatment. We evaluated the treatment changes associated with the bionator and the removable headgear splint (RHS). Methods: The sample comprised 51 consecutively treated Class II patients from 1 office who had all been successfully treated with either a bionator (n = 17) or an RHS appliance (n = 17). Class II patients waiting to start treatment later served as controls (n = 17). A modified version of the Johnston pitchfork analysis was used to quantify the dentoalveolar and skeletal contributions to the anteroposterior correction at the levels of the molars and the incisors. Results: Both appliances significantly improved anteroposterior molar relationships (2.15 mm for the bionator, 2.27 mm for the RHS), primarily by dentoalveolar modifications (1.49 and 2.36 mm for the bionator and the RHS, respectively), with greater maxillary molar distalization in the RHS group. Overjet relationships also improved significantly compared with the controls (3.11 and 2.12 mm for the bionator and the RHS, respectively), due primarily to retroclination of the maxillary incisors (2.2 and 2.38 mm for the bionator and the RHS, respectively). The differences between overall corrections and dentoalveolar modifications for both molar and overjet relationships were explained by skeletal responses, with the bionator group showing significantly greater anterior mandibular displacement than the RHS group. Conclusions: The bionator and the RHS effectively corrected the molar relationships and overjets of Class II patients primarily by dentoalveolar changes. (Am J Orthod Dentofacial Orthop 2008; 134: 732-41)