Micro-inverter for integrated grid-tie photovoltaic module using resonant controller

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Microinversor integrado ao módulo fotovoltaico para sistemas conectados à rede elétrica utilizando controlador ressonante

This paper shows the modeling and control of a single-phase full-bridge inverter with high-frequency transformer that may be used as part of a two-stage converter with transformerless DC-DC side or as a single-stage converter (simple DC-AC converter) for grid-connected PV applications. The inverter is modeled in order to obtain a small-signal transfer function used to design the P+Resonant current controller. A highfrequency step-up transformer results in reduced voltage switches and better efficiency compared with converters in which the transformer is used on the DC-DC side. Simulations and experimental results with a 200 W prototype are shown. 1

A novel voltage step-down/up ZCS-PWM Zeta converter

This paper presents an analysis of a novel pulse-width-modulated (PWM) voltage step-down/up Zeta converter, featuring zero-current-switching (ZCS) at the active switches. The applications in de to de and ac to de (rectifier) operation modes are used as examples to illustrate the performance of this new ZCS-PWM Zeta converter. Regarding to the new ZCS-PWM Zeta rectifier proposed, it should be noticed that the average-current mode control is used in order to obtain a structure with high power-factor (HPF) and low total harmonic distortion (THD) at the input current.Two active switches (main and auxiliary transistors), two diodes, two small resonant inductors and one small resonant capacitor compose the novel ZCS-PWM soft-commutation cell, used in these new ZCS-PWM Zeta converters. In this cell, the turn-on of the active switches occurs in zero-current (ZC) and their turn-off in zero-current and zero-voltage (ZCZV). For the diodes, their turn-on process occurs in zero-voltage (ZV) and their reverse-recovery effects over the active switches are negligible. These characteristics make this cell suitable for Insulated-Gate Bipolar Transistors (IGBTs) applications.The main advantages of these new Zeta converters, generated from the new soft-commutation cell proposed, are possibility of obtaining isolation (through their accumulation inductors), and high efficiency, at wide load range. In addition, for the rectifier application, a high power factor and low THD in the input current ran be obtained, in agreement with LEC 1000-3-2 standards.The principle of operation, the theoretical analysis and a design example for the new de to de Zeta converter operating in voltage step-down mode are presented. Experimental results are obtained from a test unit with 500W output power, 110V(dc) output voltage, 220V(dc) input voltage, operating at 50kHz switching frequency. The efficiency measured at rated toad is equal to 97.3%for this new Zeta converter.Finally, the new Zeta rectifier is analyzed, and experimental results from a test unit rated at 500W output power, 110V(dc) output voltage, 220V(rms) input voltage, and operating at 50kHz switching frequency, are presented. The measured efficiency is equal to 96.95%, the power-factor is equal to 0.98, and the input current THD is equal to 19.07%, for this new rectifier operating at rated load.

Establishing common elements among some science education references as a resource to design a Didactics of Physics program for teachers initial education

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The benefits of ethanol use for hydrogen production in urban transportation

The purpose of this paper is to describe the benefits of sugar cane ethanol in Brazil, appointing the productivity of this type of fuel based on hectares of plantation, its carbon dioxide cycle and the contribution to reduce the greenhouse effect. In the following step the uses of ethanol for hydrogen production by steam reforming is analyzed and some comparison with natural gas steam reforming is performed. The sugar cane industry in Brazil, in a near future, in the hydrogen era, could be modified according to our purpose, since besides the production of sugar, and ethylic and anhydric alcohol, Brazilian sugar cane industry will also be able to produce biohydrogen.Fuel cells appear like a promising technology for energy generation. Among several technologies in the present, the PEMFC (proton exchange membrane fuel cell) is the most appropriate for vehicles application, because it combines durability, high power density, high efficiency, good response and it works at relatively low temperatures. Besides that it is easy to turn it on and off and it is able to support present vibration in vehicles. A PEMFC's problem is the need of noble catalysts like platinum. Another problem is that CO needs to be in low concentration, requiring a more clean hydrogen to avoid fuel cell deterioration.One part of this paper was developed in Stockholm, where there are some buses within the CUTE (clean urban transport for Europe) project that has been in operation with FC since January 2004. Another part was developed in Guaratingueta, Brazil. Brazil intends to start up a program of FC buses. As conclusion, this paper shows the economical analysis comparing buses moved by fuel cells using hydrogen by different kinds of production. Electrolyze with wind turbine, natural gas steam reforming and ethanol steam reforming. (C) 2009 Elsevier Ltd. All rights reserved.

Reproductive responses of rabbit does to a supplemental lighting program

The objective was to investigate whether the productivity of rabbit does can be improved, when natural photoperiod is decreasing, by adopting a supplemental lighting program. Three experiments were conducted involving two groups: control, submitted to the natural decreasing photoperiod, and supplemented with a lighting program which provided 14 h light/24 h beginning at 10 weeks of age. In the first experiment, 20 nulliparous does, 10 from each group, were euthanized 8 h after being presented to a buck; the overall number of follicles, whose diameter exceeded I mm, was determined macroscopically. The right ovaries were collected, histologically analyzed, and electronically measured. In the second experiment, 30 nulliparous does, 15 from each group, were presented to a buck (day 1). Receptive does were euthanized on day 8 to evaluate embryonic survival (number of normal embryos/ovulation rate). In the third experiment, 48 nulliparous does, 24 from each group, were followed from the first presentation to the buck until the weaning of the first litter. The effect of treatment on reproductive and body weight traits of does, and litter performance traits, at birth and weaning, was evaluated. The average number of follicles whose diameter exceeded 1 mm was higher in the treatment group (12.05 +/- 1.07 vs. 8.63 +/- 1.00, P=0.03 7). Receptive does of the treatment group had heavier ovaries relative to those of the control group (790 +/- 59 vs. 470 +/- 64 mg, P=0.004), whereas no treatment difference regarding this trait was found for non-receptive ones. Treatment had a favorable effect on pregnancy rate of total exposed and of receptive does (80.0% vs. 33.3%, P=0.01, and 92.3% vs. 50.0%, P=0.02, respectively). The number of underdeveloped embryos was lower (0.067 +/- 0.380 vs. 2.500 +/- 0.455, P=0.004), embryonic survival up to day 8, and uterus weight was higher in the treatment group (0.839 +/- 0.075 vs. 0.534 +/- 0.087, P=0.033 and 13.83 +/- 0.72 vs. 10.99 +/- 0.84, P=0.037, respectively). Number of presentations tended to be lower (1.32 +/- 0.17 vs. 1.75 +/- 0.16, P=0.077) and adjusted litter size in the first reproductive cycle tended to be higher (7.09 +/- 0.89 vs. 5.22 +/- 0.68, P=0.091) in the treatment group relative to the control.

Insertion and follow-up of complete dentures: a literature review

Insertion and follow-up of complete dentures: a literature reviewObjective: The aim of this study was to present the importance of clinical procedures related to insertion and follow-up of complete dentures in elderly patients.Materials and Methods: The success of rehabilitation with complete dentures results from the accuracy of clinical and laboratorial procedures that makes the denture insertion an important step of treatment.Conclusion: The follow-up and professional maintenance of function and hygiene facilitates long-term efficiency.

Bond Strength of Two-Step Etch-and-Rinse Adhesive Systems to the Dentin of Primary and Permanent Teeth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of chlorhexidine on bond strength of two-step etch-and-rinse adhesive systems to dentin of primary and permanent teeth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nd:YAG Laser Irradiation of Etched/Unetched Dentin Through an Uncured Two-step Etch-and-Rinse Adhesive and its Effect on Microtensile Bond Strength

Purpose: To evaluate whether Nd:YAG laser irradiation of etched and unetched dentin through an uncured adhesive affected the microtensile bond strength (pTBS).Materials and Methods: Flat dentin surfaces were created in 19 extracted human third molars. Adper Single Bond (SB) adhesive was applied over etched (groups 1 to 3) or unetched dentin (groups 4 to 6). The dentin was then irradiated with a Nd:YAG laser through the uncured adhesive, using 0.75 or 1 W power settings, except for the control groups (groups 1 and 4). The adhesive was light cured and composite crowns were built up. After 24 h, the teeth were sectioned into beams, with cross-sectional areas of 0.49 mm(2), and were stressed under tension. Data were statistically analyzed using two-way ANOVA and Tukey's test (alpha = 5%). Dentin surfaces of fractured specimens and the interfaces of untested beams were observed under scanning electron microscopy (SEM).Results: Acid etching, laser irradiation, and their interaction significantly affected bonding (p < 0.05). Laser irradiation did not improve bonding of etched dentin to resin (p > 0.05). However, higher pTBS means were found on unetched lased dentin (groups 5 and 6), but only in comparison to group 4, where neither lasing nor etching was performed. Groups 4 to 6 showed the lowest pTBS means among all groups tested (p < 0.05). Laser irradiation did not change the characteristics of the hybrid layers created, while solidification globules were observed on lased dentin surfaces under SEM.Conclusion: Laser irradiation of dentin through the uncured adhesive did not significantly improve the pTBS in comparison to the suggested manufacturer's technique.

Oral cleft prevention program (OCPP)

Background: Oral clefts are one of the most common birth defects with significant medical, psychosocial, and economic ramifications. Oral clefts have a complex etiology with genetic and environmental risk factors. There are suggestive results for decreased risks of cleft occurrence and recurrence with folic acid supplements taken at preconception and during pregnancy with a stronger evidence for higher than lower doses in preventing recurrence. Yet previous studies have suffered from considerable design limitations particularly non-randomization into treatment. There is also well-documented effectiveness for folic acid in preventing neural tube defect occurrence at 0.4 mg and recurrence with 4 mg. Given the substantial burden of clefting on the individual and the family and the supportive data for the effectiveness of folic acid supplementation as well as its low cost, a randomized clinical trial of the effectiveness of high versus low dose folic acid for prevention of cleft recurrence is warranted.Methods/design: This study will assess the effect of 4 mg and 0.4 mg doses of folic acid, taken on a daily basis during preconception and up to 3 months of pregnancy by women who are at risk of having a child with nonsyndromic cleft lip with/without palate (NSCL/P), on the recurrence of NSCL/P. The total sample will include about 6,000 women (that either have NSCL/P or that have at least one child with NSCL/P) randomly assigned to the 4 mg and the 0.4 mg folic acid study groups. The study will also compare the recurrence rates of NSCL/P in the total sample of subjects, as well as the two study groups (4mg, 0.4 mg) to that of a historical control group. The study has been approved by IRBs (ethics committees) of all involved sites. Results will be disseminated through publications and presentations at scientific meetings.Discussion: The costs related to oral clefts are high, including long term psychological and socio-economic effects. This study provides an opportunity for huge savings in not only money but the overall quality of life. This may help establish more specific clinical guidelines for oral cleft prevention so that the intervention can be better tailored for at-risk women.

Stretching Exercise Program Improves Gait in the Elderly

Background: Ageing is characterized by a number of physical changes that contribute to a decline in the ability to perform daily tasks. Stretching has been proposed to reduce hip flexion contracture and increase hip and pelvis range of motion, thus improving gait performance. Objective: The purpose of this study was to determine whether a supervised stretching program designed to improve the range of motion of the lower limbs alters gait kinematics in older adults. Methods: Twenty healthy older adult women (65.9 +/- 4.2 years old and BMI 24.9 +/- 3.5) were divided into 2 groups. The experimental group undertook 12 sessions of stretching exercises, whereas the control group did not engage in any physical activity. Gait performance was assessed at the beginning of the experiment and after the 4-week intervention period. Results: Those in the experimental group showed increased step length, higher velocity and reduced double support time after training. In addition, participants involved in the stretching program showed greater anterior and lateral pelvis tilt and also greater rotation (p < 0.05). Conclusions: Based on our results, we can suggest that a supervised stretching program is effective to alter a number of gait variables. Moreover, after the stretching protocol, aged participants displayed gait parameters which were similar to those reported in young healthy adults. Therefore, stretching can be used as an effective means to improve range of motion and reverse some age-related changes that influence gait performance. Copyright (C) 2009 S. Karger AG, Basel

Extraction and clean-up procedure for analysis of organochlorine pesticide residues in ethoxylated lanolin

In the present study an evaluation was made of a method for the determination of organochlorine pesticide residues in ethoxylated lanolin. Samples were homogenized with Celite, transferred to chromatographic columns, prepacked with silica gel deactivated to 10%. The pesticide elution was processed with n-hexane-dichloromethane and the concentrated eluate was analyzed using gas-liquid chromatography (GC) with electron capture detection (ECD). The composition of the elution solvent was a significant factor for the recovery of the pesticides. Mean recoveries obtained for fortified samples ranged from 87 to 94% for p,p'-DDE, dieldrin, endrin, p,p'-DDD and p,p'-DDT. Optimization of the experimental conditions resulted in a small-scale method that combines extraction and cleanup in a single step. (C) 2000 Elsevier B.V. S.A. All rights reserved.

TRICUT: a program to clip triangle meshes using the rapid and triangle libraries and the visualization toolkit

An efficient technique to cut polygonal meshes as a step in the geometric modeling of topographic and geological data has been developed. In boundary represented models of outcropping strata and faulted horizons polygonal meshes often intersect each other. TRICUT determines the line of intersection and re-triangulates the area of contact. Along this line the mesh is split in two or more parts which can be selected for removal. The user interaction takes place in the 3D-model space. The intersection, selection and removal are under graphic control. The visualization of outcropping geological structures in digital terrain models is improved by determining intersections against a slightly shifted terrain model. Thus, the outcrop line becomes a surface which overlaps the terrain in its initial position. The area of this overlapping surface changes with respect to the strike and dip of the structure, the morphology and the offset. Some applications of TRICUT on different real datasets are shown. TRICUT is implemented in C+ + using the Visualization Toolkit in conjunction with the RAPID and TRIANGLE libraries. The program runs under LINUX and UNIX using the MESA OpenGL library. This work gives an example of solving a complex 3D geometric problem by integrating available robust public domain software. (C) 2002 Elsevier B.V. Ltd. All rights reserved.

UV-visible absorption characteristics of TEOS-derived and Cr-doped silica sonogels aged in different pH solutions and heat treated up to 600 degrees C

Cr-doped xerogels were obtained by sol-gel process from the acid-catalyzed and ultrasound-stimulated hydrolysis of tetraethoxysilane (TEOS) with addition of CrCl3.6H(2)O in water solution during the liquid step of the process. The gels were aged immersed in different pH solutions for about 30 days, after that they were allowed to dry. The samples were annealed at temperatures ranging from 40 to 600degreesC and analyzed by UV-visible absorption spectroscopy. Cr3+ is the preferable oxidation state of the chromium ion in the gels annealed up to 250-300degreesC, in the case of aging in solutions of pH=5 and 11. A high UV absorption below similar to320 nm, due to the host gel, and different absorption bands, depending on the temperature, due to the chromium ion were observed in the xerogels at temperatures below similar to250degreesC, in the case of aging in solutions of pH=1 and 2. These absorption bands have not been assigned. Above 300degreesC up to 600degreesC, Cr5+, and possibly Cr6+, are the preferable oxidation states of the chromium ion independent of the pH of the aging solution, so the xerogels turn to a yellowish appearance in all cases.