Análises tectono-estratigráfica e faciológico-diagenética da coquina-reservatório Lagoa Feia, Campo de Linguado, Bacia de Campos

A tectono-stratigraphic study of bivalve coquina-reservoir of Linguado Field allowed to identify two trends of permoporosity development. The delineation of these depositional-diagenetic traps were made through structural and stratigrafic cross-sections and maps. It resulted in the identification of shelf-ramp systems (tilted to SSE), it tickens from 60 to 70 meters and ends against an antithetic fault. The main coquina is bounded by fine siliciclastic units, white clay (low Gamma Ray values) or shale (high Gamma Ray values) lithologies, influencing diagenesis of basal or top coquina limestones (cimented, non-porous). Also in the middle of coquina-reservoir the “clayer” material is also associated with cemented carbonates, with also compartimentalize the reservoir into two subzones. The coquina porosity of the subzones is taken from density-neutron logs, while induction log estimates permeabilities and fluid saturations. It’s noticed the porosity development into pairs, good one followed by a regular/poor one and vice versa. These pairs form verticals succession, pair cycles where porosity improves or decreases upwards. These two scales of pore heterogeneity impose strong layering to the reservoir, and influences fluid saturations, oil-water contacts and porosity cut-offs. In a cross-section with density and induction logs, it can be observed the porosity variation along the shelf-ramp coquina (between 3LI_0004_RJS e 3RJS_0157C_RJ), the porosity is better developed in a downdip direction in the case of the two shelf wells, and also be the three ramp wells. The southern west downdip, 3RJS_0157C_RJ well, has best porosity pairs-cycles; however, its lowest structural conditions favour water saturation. Therefore it is fundamental for reservoir fluid evaluation a cross-plot analysis of RHOB-NPHI and Induction logs

Influência do condicionamento ambiental sobre as propriedades viscoelásticas de compósitos aramida/epóxi

The increasing application of structural composites in the aerospace industry is mainly due to its low specific weight coupled with its excellent mechanical properties when in service. As a result of climatic variations that pass the aircraft is of paramount importance to study the influence of weathering on this type of material when subjected to such changes. The purpose of this work is to evaluate the mechanical behavior of specimens of kevlar fiber /epoxy matrix composites, by dynamic mechanical thermal analysis (DMA) and interlaminar shear strength tests (ILSS), after passing through three environmental conditioning: saline fog, hygrothermal and ultraviolet radiation. From the results, we concluded that the laminate was molded supplied homogeneously, not presenting problems such as porosity, delaminations or cracks inside. After a period of 625 hours of exposure to hygrothermal conditioning, we observed a 1,2% maximum of absorption of moisture. Samples subjected to the conditioning by UV irradiation (600 hours) and salt spray showed a reduction of about 24,30% and 32,30%, respectively, on the shear strength (ILSS). In DMA analysis is not observed significant changes on the glass transition temperature. However, when considering the storage modulus of the samples conditioned by UV radiation (1200 hours), salt spray and hygrothermal conditioning there is an increase of 5,34% , 7,19% and 5,57% respectively

Estudo das características fluidodinâmicas do bagaço de cana de açúcar para aplicações da gaseificação no setor sucroalcooleiro

In this work is studied the fluid dynamic characteristics of sugarcane bagasse for gasification applications and use of syngas in the sugarcane sector. This is an experimental work, which is initially performed the particle size separation of sugarcane bagasse particles, using appropriate equipment. Through the experiment is possible to determine the average diameter of particles pomace typical sugarcane mill. The equipment used for the grading sieve separation assembly consists of several dimensions, arranged vertically and which shows adequate for good separation from the pulp. Later, it makes immediate analysis for the determination of moisture, ash, volatile materials and fixed carbon. The study also determines the gross calorific value and allows analysis of densities of particles of sugar cane bagasse. Also studied the bagasse morphology using electron microscopes, where it was possible to visualize the geometry of the particles of bagasse. The use of Electronic Scanning Microscopy (SEM) provided better understand the morphology and particle size measured by using photography methods. Two methods for determining the sphericity of the particles were also used. The experiments carried out using appropriate standards and specific equations, allowing compare the present results with the values found by several researchers. Subsequently, fluid dynamic simulations were performed for the determination of porosity and minimum fluidization velocity theoretical. It follows that the sphericity and porosity of the bagasse particles influence the minimum fluidization velocity of biomass

Aplicação da membrana de látex natural (NRL) como suporte para cultura das células osteogênicas MC3T3-E1 para regeneração óssea guiada (GBR)

Pós-graduação em Biotecnologia - IQ

Estudo de propriedades da resina acrílica termoativada por energia de micro-ondas frente às variações nos procedimentos de inclusão

On heat cured acrylic resins by microwaves energy the action of electromagnetic waves on methylmethacrylate promote the polymerization process. However, part of this energy is absorbed by the gypsum present in the flask and the function of this gypsum is to maintain the characteristics of specimen, nevertheless is unknown in the literature as the amount of water present in this gypsum affects the characteristics of acrylic resin. The proposal of this study was verified if dried gypsum influenced in some properties of the acrylic resins thermally activated by microwaves: presence of porosity, microhardness, roughness, flexural strength and dimensional change. Two different types of acrylic resin for complete denture were utilized: Lucitone 550 e Vipi-Wave and groups were formed: Lucitone 550, polymerization by microwave energy without gypsum treatment; Lucitone 550, polymerization by microwave energy with pretreatment gypsum; Vipi-Wave by microwave energy without gypsum treatment; Vipi Wave, polymerization by microwave energy with pretreatment gypsum; Lucitone 550 control group polymerization in hot water bath. For both situations were performed analysis of microhardness and porosity three different metallic shaped specimens were formed with followed dimensions: 2,0x2,0x2,0cm (8cm3); 2,0x2,0x1,0 (4cm3) e 2,0x2,0x0,5 (2cm3). Standardized wax specimens was used to prepare groups (n=9) and included in glass fiber flasks. The gypsum dry was made by microwave oven cycle (10min and 600W) and then the flasks were maintained in dry oven during two hours. Polymerizations of specimens were made and then polished. Wax patterns #7 obtained from the metal were embedded in plastic flask and following the processes of pressing and polymerization of the resin according to established groups. To evaluate the flexural strength, specimens 65mm x 10mm x 3.0mm from metallic patterns in bar format were made. ...

Evaluation of the bleached human enamel by scanning electron microscopy

Since bleaching has become a popular procedure, the effect of peroxides on dental hard tissues is of great interest in research. Purpose: The aim of this in vitro study was to perform a qualitative analysis of the human enamel after the application of in-office bleaching agents, using Scanning Electron Microscopy (SEM). Materials and Methods: Twenty intact human third molars extracted for orthodontic reasons were randomly divided into four groups (n=5) treated as follows: G1- storage in artificial saliva (control group); G2- four 30-minute applications of 35% carbamide peroxide (total exposure: 2h); G3- four 2-hour exposures to 35% carbamide peroxide (total exposure: 8h); G4- two applications of 35% hydrogen peroxide, which was light-activated with halogen lamp at 700mW/cm2 during 7min and remained in contact with enamel for 20min (total exposure: 40min). All bleaching treatments adopted in this study followed the application protocols advised by manufacturers. Evaluation of groups submitted to 35% carbamide peroxide was carried out after two time intervals (30 minutes and 2 hours per session), following the extreme situations recommended by the manufacturer. Specimens were prepared for SEM analysis performing gold sputter coating under vacuum and were examined using 15kV at 500x and 2000x magnification. Results: Morphological alterations on the enamel surface were similarly detected after bleaching with either 35% carbamide peroxide or 35% hydrogen peroxide. Surface porosities were characteristic of an erosive process that took place on human enamel. Depression areas, including the formation of craters, and exposure of enamel rods could also be detected. Conclusion: Bleaching effects on enamel morphology were randomly distributed throughout enamel surface and various degrees of enamel damage could be noticed. Clinical significance: In-office bleaching materials may adversely affect enamel morphology and therefore should be used with caution.

Para além da heteronormatividade: uma análise dos eunucos representados por Estácio, Marcial e Suetônio (Roma, 80-121 d. C)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)