Using shifts in the electronic emission curve to evaluate polymer surface degradation

The polymer surface degradation and/or modification evolution of Teflon FEP and Mylar C films caused by a low energy electron beam were analyzed using a new method that consists in measuring the second crossover energy shift in the electronic emission curve. Upon prolonged irradiation, the second crossover energy shifts irreversibly to lower values in Teflon FEP but to higher values in Mylar C, indicating distinct mechanisms of surface degradation for the two polymers. The method represents a relatively inexpensive way to monitor early stages of surface degradation since the secondary electron emission comes from a maximum depth below the geometric surface of 100 mn in insulators. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Electrogravimetric Real-Time and in Situ Michaelis-Menten Enzimatic Kinetics: Progress Curve of Acetylcholinesterase Hydrolysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparison of proton energy loss in thick absorbers in terms of a reduced calibration curve

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Application of dissociation curve analysis to radiation hybrid panel marker scoring: generation of a map of river buffalo (B-bubalis) chromosome 20

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Characteristics of the double-torsion test to determine the R-curve of ceramic materials

Double-torsion tests were carried out on a commercial ceramic floor tile to verify whether this test is suitable for determining the R-curve of ceramics. The instantaneous crack length was obtained by means of compliance calibration, and it was found that the experimental compliance underestimates the real crack length. The load vs. displacement curves were also found to drop after maximum loading, causing the stress intensity factor to decline. The R-curves were calculated by two methods: linear elastic fracture mechanics and the energetic method. It was obtained that the average values of crack resistance, R, and the double of the work of fracture, 2 · γwof, did not depend on notch length, a0, which is a highly relevant finding, indicating that these parameters were less dependent on the test specimen's geometry. The proposal was to use small notches, which produce long stable crack propagation paths that in turn are particularly important in the case of coarse microstructures.

Reduced calibration curve for proton computed tomography

The pCT deals with relatively thick targets like the human head or trunk. Thus, the fidelity of pCT as a tool for proton therapy planning depends on the accuracy of physical formulas used for proton interaction with thick absorbers. Although the actual overall accuracy of the proton stopping power in the Bethe-Bloch domain is about 1%, the analytical calculations and the Monte Carlo simulations with codes like TRIM/SRIM, MCNPX and GEANT4 do not agreed with each other. A tentative to validate the codes against experimental data for thick absorbers bring some difficulties: only a few data is available and the existing data sets have been acquired at different initial proton energies, and for different absorber materials. In this work we compare the results of our Monte Carlo simulations with existing experimental data in terms of reduced calibration curve, i.e. the range - energy dependence normalized on the range scale by the full projected CSDA range for given initial proton energy in a given material, taken from the NIST PSTAR database, and on the final proton energy scale - by the given initial energy of protons. This approach is almost energy and material independent. The results of our analysis are important for pCT development because the contradictions observed at arbitrary low initial proton energies could be easily scaled now to typical pCT energies. © 2010 American Institute of Physics.

Comparison of the GEANT4 releases 8.2 and 9.2 in terms of a pCT reduced calibration curve

The GEANT4 simulations are essential for the development of medical tomography with proton beams pCT. In the case of thin absorbers the latest releases of GEANT4 generate very similar final spectra which agree well with the results of other popular Monte Carlo codes like TRIM/SRIM, or MCNPX. For thick absorbers, however, the disagreements became evident. In a part, these disagreements are due to the known contradictions in the NIST PSTAR and SRIM reference data. Therefore, it is interesting to compare the GEANT4 results with each other, with experiment, and with diverse code results in a reduced form, which is free from this kind of doubts. In this work such comparison is done within the Reduced Calibration Curve concept elaborated for the proton beam tomography. © 2010 IEEE.

Interval multivariate curve resolution in the dereplication of HPLC-DAD data from Jatropha gossypifolia

Introduction Jatropha gossypifolia has been used quite extensively by traditional medicine for the treatment of several diseases in South America and Africa. This medicinal plant has therapeutic potential as a phytomedicine and therefore the establishment of innovative analytical methods to characterise their active components is crucial to the future development of a quality product. Objective To enhance the chromatographic resolution of HPLC-UV-diode-array detector (DAD) experiments applying chemometric tools. Methods Crude leave extracts from J. gossypifolia were analysed by HPLC-DAD. A chromatographic band deconvolution method was designed and applied using interval multivariate curve resolution by alternating least squares (MCR-ALS). Results The MCR-ALS method allowed the deconvolution from up to 117% more bands, compared with the original HPLC-DAD experiments, even in regions where the UV spectra showed high similarity. The method assisted in the dereplication of three C-glycosylflavones isomers: vitexin/isovitexin, orientin/homorientin and schaftoside/isoschaftoside. Conclusion The MCR-ALS method is shown to be a powerful tool to solve problems of chromatographic band overlapping from complex mixtures such as natural crude samples. Copyright © 2013 John Wiley & Sons, Ltd. Extracts from J. gossypifolia were analyzed by HPLC-DAD and, dereplicated applying MCR-ALS. The method assisted in the detection of three C-glycosylflavones isomers: vitexin/isovitexin, orientin/homorientin and schaftoside/isoschaftoside. The application of MCR-ALS allowed solving problems of chromatographic band overlapping from complex mixtures such as natural crude samples. Copyright © 2013 John Wiley & Sons, Ltd.

Estudo comparativo do modelo linear de Heffron e Phillips e modelo de sensibilidade de potência com a inclusão dos dispositivos FACTS SVC e TCSC

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Multivariate curve resolution analysis applied to time-resolved synchrotron X-ray Absorption Spectroscopy monitoring of the activation of copper alumina catalyst

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influence of salts on the coexistence curve and protein partitioning in nonionic aqueous two-phase micellar systems

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparison of growth curve parameters of organs and body components in meat- (Coturnix coturnix coturnix) and laying-type (Coturnix coturnix japonica) quail show interactions between gender and genotype

The objective of this study was to estimate growth parameters of carcass components (wing, thighs and drumsticks, back and breast) and organs (heart, liver, gizzard and gut) in males and females of one meat-type quail strain (Coturnix coturnix coturnix) and two laying strains (Coturnix coturnix japonica) designated either yellow or red.A total of 1350 quail from 1 to 42d old were distributed in a completely randomised design, with 5 replicates of each strain. The carcass component weights and body organs were analysed weekly and evaluated using the Gompertz function; growth rates were evaluated through derivative equations.The meat-type strain presented the highest growth rates in carcass components and organs. Across strains, females showed the highest weight of internal organs at maturity compared to males.Females had greater growth potential in breast, wings and back than males for both yellow and red laying quail.