Effect of different methods of cutting fluid application on turning of a difficult-to-machine steel (SAE EV-8)

In this study, different methods of cutting fluid application are used in turning of a difficult-to-machine steel (SAE EV-8). Initially, a semisynthetic cutting fluid was applied using a conventional method (i.e. overhead flood cooling), minimum quantity of cutting fluid, and pulverization. A lubricant of vegetable oil (minimum quantity of lubricant) was also applied using the minimum quantity method. Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface, top surface of the chip (between workpiece and chip) and tool-workpiece contact. Moreover, two other methods were used: an interflow between conventional application and chip-tool interface jet (combined method) and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high-pressure system using a piston pump for generating a cutting fluid jet, a venturi for fluid application (minimum quantity of cutting fluid and minimum quantity of lubricant) and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. Among the results, it can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure, such as minimum quantity of volume and pulverization, when considering just the cutting tool wear. © 2013 IMechE.

Different methods of cutting fluid application on turning of a difficult-to-machine steel

Different methods of cutting fluid application are used on turning of a difficult-tomachine steel (SAE EV-8). A semi-synthetic cutting fluid was applied using a conventional method, minimum quantity of cutting fluid (MQCF), and pulverization. By the minimum quantity method was also applied a lubricant of vegetable oil (MQL). Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface; top surface of the chip; and tool-workpiece contact. Two other methods were used: an interflow between conventional application and chip-tool interface jet and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high pressure system using a piston pump for generating a cutting fluid jet, a Venturi for fluid application (MQCF and MQL), and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. It can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure. © (2013) Trans Tech Publications, Switzerland.

Effect of s/g ratio on kraft pulping and ecf bleaching of some poplars and eucalyptus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effects of plant regulators on the growth and flowering of Saint Augustine grass plants

The objective of this work was to evaluate the effects of three plant growth inhibitors on the development and emission of floral rachis of Saint Augustine grass [Stenotaphrum secundatum (Walt.) Kuntzel] plants. The study was carried out in a 15 month old lawn with the experimental plots being distributed in accordance with a complete randomized block design with four replications. The treatments consisted of sole application of trinexapac-ethyl (113, 226, 452, 678, and 904 g ai ha(-1)), prohexadione-calcium (100 and 200 g ai ha(-1)), and bispyribac-sodium (40 and 60 g ai ha(-1)) plus a check treatment in which the plants were not submitted to any of the plant growth inhibitors. The effects of those products were evaluated in terms of visual signs of plant intoxication, plant height, emission and height of floral rachises, and chip total dry matter production. All the plant growth inhibitors resulted in visible injury to the plants but these intoxication signs practically disappeared 28 days after the application. Trinexapac-ethyl at the dose of 904 g ai ha(-1) reduced plant height by 59.7%, the emission of floral rachis by 96.4%, and the amount of chip dry matter production by 87.7%. Plant growth inhibitors may reduce the number of times of lawn plants cutting up to 119 days after their application with no harmful effects on the plants visual aspect.