Determination of the numerical parameters of a continuous damage model for the structural analysis of clay brick masonry

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Hygrothermal effects on damping behavior of metal/glass fiber/epoxy hybrid composites

Continuous fiber/metal laminates (FML) offer significant improvements over current available materials for aircraft structures due to their excellent fatigue endurance and low density. Glass fibers/epoxy laminae and aluminum foil (Glare) are commonly used to obtain these hybrid composites. The environmental factors can limit the applications of composites by deteriorating the mechanical properties during service. Usually, epoxy resins absorb moisture when exposed to humid environments and metals are prone to surface corrosion. Therefore, the combination of the two materials in Glare (polymeric composite and metal). can lead to differences that often turn out to be beneficial in terms of mechanical properties and resistance to environmental influences. In this work. The viscoelastic properties. such as storage modulus (E') and loss modulus (E'), were obtained for glass fiber/epoxy composite, aluminum 2024-T3 alloy and for a glass fiber/epoxy/aluminum laminate (Glare). It was found that the glass fiber/epoxy (G/E) composites decrease the E' modulus during hygrothermal conditioning up to saturation point (6 weeks). However, for Glare laminates the E' modulus remains unchanged (49GPa) during the cycle of hygrothermal conditioning. The outer aluminum sheets in the Glare laminate shield the G/E composite laminae from moisture absorption. which in turn prevent, in a certain extent, the material from hygrothermal degradation effects. (c) 2005 Elsevier B.V. All rights reserved.

NOVEL CELLULOSE/NbOPO4 center dot nH(2)O HYBRID MATERIAL FROM SUGARCANE BAGASSE

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

An effortless hybrid method to solve economic load dispatch problem in power systems

This paper proposes a new approach and coding scheme for solving economic dispatch problems (ED) in power systems through an effortless hybrid method (EHM). This novel coding scheme can effectively prevent futile searching and also prevents obtaining infeasible solutions through the application of stochastic search methods, consequently dramatically improves search efficiency and solution quality. The dominant constraint of an economic dispatch problem is power balance. The operational constraints, such as generation limitations, ramp rate limits, prohibited operating zones (POZ), network loss are considered for practical operation. Firstly, in the EHM procedure, the output of generator is obtained with a lambda iteration method and without considering POZ and later in a genetic based algorithm this constraint is satisfied. To demonstrate its efficiency, feasibility and fastness, the EHM algorithm was applied to solve constrained ED problems of power systems with 6 and 15 units. The simulation results obtained from the EHM were compared to those achieved from previous literature in terms of solution quality and computational efficiency. Results reveal that the superiority of this method in both aspects of financial and CPU time. (C) 2011 Elsevier Ltd. All rights reserved.

Frequency synthesizer using a hybrid analog/digital loop filter: A low complexity approach

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Structure and microstructure of PbTiO3 thin films obtained from hybrid chemical method

PbTiO3 thin films were deposited on Si(100) via hybrid chemical method and crystallized between 400 and 700 degreesC to study the effect of the crystallization kinetics on structure and microstructure of these materials. X-ray diffraction (XRD) technique was used to study the structure of the crystallized films. In the temperature range investigated, the lattice strain (c/a) presented a maximum value (c/a = 1.056) for film crystallized at 600 degreesC for I h. Atomic force microscopy (AFM) was used in investigation of the microstructure of the films. The rms roughness of the films linearly increases with temperature and ranged from 1.25 to 9.04 nm while the grain sizes ranged from 130.6 to 213.6 nm. Greater grain size was observed for film crystallized at 600 degreesC for 1 h. (C) 2002 Elsevier B.V. S.A. All rights reserved.

Modular hybrid total hip arthroplasty. Experimental study in dogs

Background: This prospective experimental study evaluated the surgical procedure and results of modular hybrid total hip arthroplasty in dogs.Methods: Ten skeletally mature healthy mongrel dogs with weights varying between 19 and 27 kg were used. Cemented modular femoral stems and uncemented porous-coated acetabular cups were employed. Clinical and radiographic evaluations were performed before surgery and at 30, 60, 90, 120, 180 and 360 days post-operation.Results: Excellent weight bearing was noticed in the operated limb in seven dogs. Dislocation followed by loosening of the prosthesis was noticed in two dogs, which were therefore properly treated with a femoral head osteotomy. Femoral fracture occurred in one dog, which was promptly treated with full implant removal and femoral osteosynthesis.Conclusions: The canine modular hybrid total hip arthroplasty provided excellent functionality of the operated limb.

Hybrid layer thickness and resin tag length of a self-etching adhesive bonded to sound dentin

Objectives: the purpose of this study is to employ optical microscopy to measure the thickness of the hybrid layer and the penetration (tags) of an aggressive self-etching adhesive system into sound dentin.Methods: occtusat cavities were prepared in 40 extracted human posterior teeth. The prepared teeth were randomly assigned to four experimental groups with 10 specimens each. The self-etching adhesive system Adper Prompt L-Pop was applied to the dentin surface as follows: Group 1: cavosurface enamel was etched for 60 s and dentin for 20 s with 35% phosphoric acid get, immediately followed by application of the self -etching adhesive with a brush to the entire cavity for 15 s; Groups 2, 3, and 4: no pre-etching was performed, and the self -etching adhesive was applied to both enamel and dentin for 15, 30 and 45 s, respectively. After curing, the cavities were fitted with composite resin Fittek Z250. Afterwards, the teeth were decalcified and the restorations were carefully removed for later embedding in paraffin. The specimens were serially sectioned at 6 mu m of thickness and sequentially mounted in glass slides. These sections were stained with Brown and Brenn staining for posterior analysis and measurement of the hybrid layer and resin tags on a tight microscope with a micrometric ocular 40/075. The results were submitted to analysis of variance at the 5% level.Results: whenever there was significance, the Tukey test was applied at the 5% level. The specimens receiving application of acid etching before the selfetching. adhesive displayed a larger thickness of the hybrid layer; on the other hand, specimens receiving only application of the self -etching adhesive on dentin for 15, 30 and 45 s exhibited similar thickness of the hybrid layer. As regards the resin tags, no statistically significant differences could be found between the study groups.Conclusions: it could be concluded that the increase in the time of application of the self-etching adhesive Adper Prompt L-Pop did not significantly influence the formation and thickness of hybrid layer, as well as its penetration into the sound dentin surface. (c) 2005 Elsevier Ltd. All rights reserved.

Evaluation of the Smear Layer and Hybrid Layer in Noncarious and Carious Dentin Prepared by Air Abrasion System and Diamond Tips

Purpose: To analyze the smear layer and the hybrid layer in noncarious and carious dentin prepared by different cutting instruments and restored with composite resin. Study design: Cavities were randomly prepared in 160 specimens (noncarious and artificial carious dentin) by high-speed diamond tips (KG Sorensen 1013), air abrasion system (Prepstart, Danville Engineering), ultrasonic tip (CVDentus 8.3231-1), and ultrasonic tip associated with ultrasonic cavitation by water for 10 s. Half of the cavities in each group were conditioned with 37% phosphoric acid for 15 s. The amount of smear layer and dentinal tubules present were analyzed using scanning electron microscopy and graded from 0 to 3. Cavities were prepared in another 20 noncarious specimens and 20 carious specimens and restored with adhesive composite resin system. The restorations were hemisected longitudinally and analyzed using scanning electron microscopy to evaluate the hybrid layer and resinous prolongation characteristics, using scores ranging from 1 to 6. Results: The data were statistically analyzed using Kruskal-Wallis and Dunn tests at 5% of significance level. There was evidence that the most efficient smear layer removal was the acid etching in the noncarious dentin and the water ultrasonic cavitation in the carious dentin. The hybrid layer formed on the noncarious and carious dentin prepared by the ultrasonic tip was more regular than in the specimens prepared by high-speed diamond tip, with many resinous prolongations. Conclusion: The ultrasonic tip seems to be a promising tool for carious dentin cavity preparation. Microsc. Res. Tech. 73:597-605, 2010. (C) 2009 Wiley-Liss, Inc.

In vitro growth of Brassocattleya orchid hybrid in different concentrations of KNO3, NH4NO3 and benzylaminopurine

Entre as maiores aplicações da cultura de tecidos de plantas está a propagação massal de mudas de plantas ornamentais. O objetivo deste trabalho foi avaliar o cultivo in vitro de um híbrido de orquídea Brassocattleya em diferentes concentrações de NH4NO3, KNO3 e BAP. Foram utilizadas sementes do híbrido de orquídea Brassocattleya 'Pastoral' e as plantas foram cultivadas em meio MS com redução pela metade das fontes de P, Mg e Ca e adição de 25 g L-1 de sacarose, 100 mg L-1 de mio-inositol, 1,5 g L-1 de carvão ativo e 6,5 g L-1 de ágar-ágar, sendo o pH ajustado para 5,8. Como tratamentos foram usados quatro concentrações dos sais NH4NO3 e KNO3 (2x; 1x; ½ e ¼ do meio MS) e três concentrações de BAP (0,0; 0,5 e 1,0 mg L-1). Avaliou-se a multiplicação, o crescimento em altura, massa fresca e seca, além dos teores de açucares redutores na massa seca das mudas. Observou-se grande influência das doses de NH4NO3 e KNO3 sobre o crescimento em altura das mudas, massa fresca e seca e teores de açucares redutores em Bc. ('Pastoral' x Auto). A dose de ¼ da utilizada no meio MS promoveu aumento significativo do crescimento das plantas. Para multiplicação, houve melhor resultado com a dose de ½ dos sais NH4NO3 e KNO3 utilizados no meio MS e 1,0 mg L-1 de BAP.

Gibberellic acid in vegetative and reproductive development of Phalaenopsis orchid hybrid genus

O setor de floricultura movimenta cerca de um bilhão de dólares no Brasil e o desenvolvimento de técnicas direcionadas ao controle do florescimento é necessário. O presente trabalho avaliou a influência do ácido giberélico (GA3) no desenvolvimento vegetativo e reprodutivo de plantas jovens de Phalaenopsis FSNT 'Dai-Itigo', híbrido de coloração rósea. A aplicação do GA3 foi feita via pulverização foliar nas concentrações de 0, 125, 250, 500 e 1.000 mg L -1. O comprimento das folhas aumentou consideravelmente com o uso do GA3 em baixas concentrações, porém houve diminuição da largura foliar das plantas tratadas com esse fitorregulador. A aplicação do GA3 na concentração de 125 mg L -1 apresentou os melhores resultados para a promoção do florescimento e qualidade da floração deste híbrido de orquídea. Nesse tratamento, aproximadamente 50% das plantas pulverizadas apresentaram floração cerca de 6-12 meses antes da floração das plantas sem aplicação do fitorregulador. em conclusão, a qualidade da floração e das flores foi melhor no tratamento com 125 mg L -1 de GA3.

First radiation hybrid map of the river buffalo X chromosome (BBUX) and comparison with BTAX

We report the first radiation hybrid map of the river buffalo X chromosome generated from a recently constructed river buffalo (Bubalus bubalis) whole-genome radiation hybrid panel (BBURH5000). This map contains a total of 33 cattle-derived markers, including 10 genes, four ESTs and 19 microsatellites. The markers are distributed in two linkage groups: LG1 contains eight markers spanning 125.6 cR, and LG2 contains 25 markers spanning 366.3 cR. LG1 contains six markers in common with bovine sequence assembly BUILD 3.1. With the exception of BMS2152, the order of these markers on our BBUX map is shuffled when compared to the cow X chromosome (Bos taurus; BTAX). From LG2, two markers (AMELX and BL22) map to a more distal portion of BTAX compared to BBUX. In addition, two pairs of LG2 markers exhibit inversions compared to BTAX (ILSTS017 and ATRX; XBM38 and PPEF1). Alternatively, when compared to the most recent bovine RH map (Bov-Gen 3000rads), BL1098 and BMS2227 from LG1 as well as PLS3 and BMS1820 from LG2 showed inverted positions on the BBUX map. These discrepancies in buffalo and cattle maps may reflect evolutionary divergence of the chromosomes or mapping errors in one of the two species. Although the set of mapped markers does not cover the entire X chromosome, this map is a starting point for the construction of a high-resolution map, which is necessary for characterization of small rearrangements that might have occurred between the Bubalus bubalis and Bos taurus X chromosomes.

Construction of a river buffalo (Bubalus bubalis) whole-genome radiation hybrid panel and preliminary RH mapping of chromosomes 3 and 10

The buffalo (Bubalus bubalis) not only is a useful source of milk, it also provides meat and works as a natural source of labor and biogas. To establish a project for buffalo genome mapping a 5,000-rad whole genome radiation hybrid panel was constructed for river buffalo and used to build preliminary RH maps from two chromosomes (BBU 3 and BBU10). The preliminary maps contain 66 markers, including coding genes, cattle ESTs and microsatellite loci. The RH maps presented here are the starting point for mapping additional loci, in particular, genes and expressed sequence tags that will allow detailed comparative maps between buffalo, cattle and other species to be constructed. A large quantity of DNA has been prepared from the cell lines forming the RH panel reported here and will be made publicly available to the international community both for the study of chromosome evolution and for the improvement of traits important to the role of buffalo in animal agriculture.

Effect of Biomimetic Remineralization on the Dynamic Nanomechanical Properties of Dentin Hybrid Layers

The mineral and organic phases of mineralized dentin contribute co-operatively to its strength and toughness. This study tested the null hypothesis that there is no difference in nano-dynamic mechanical behavior (complex modulus-E*; loss modulus-E ''; storage modulus-E'; in GPa) of dentin hybrid layers (baseline: E*, 3.86 +/- 0.24; E '', 0.23 +/- 0.05; E', 3.85 +/- 0.24) created by an etch-and-rinse adhesive in the presence or absence of biomimetic remineralization after in vitro aging. Using scanning probe microscopy and nano-dynamic mechanical analysis, we demonstrated that biomimetic remineralization restored the nano-dynamic mechanical behavior of heavily remineralized, resin-sparse regions of dentin hybrid layers (E*, 19.73 +/- 3.85; E '', 8.75 +/- 3.97; E', 16.02 +/- 2.58) to those of the mineralized dentin base (E*, 19.20 +/- 2.42; E '', 6.57 +/- 1.96; E', 17.39 +/- 2.0) [p > 0.05]. Conversely, those resin-sparse, water-rich regions degraded in the absence of biomimetic remineralization, with significant decline [p < 0.05] in their complex and storage moduli (E*, 0.83 +/- 0.35; E '', 0.88 +/- 0.24; E', 0.62 +/- 0.32). Intrafibrillar apatite deposition preserves the integrity of resin-sparse regions of hybrid layers by restoring their nanomechanical properties to those exhibited by mineralized dentin.

Status of a hybrid three-neutrino interpretation of neutrino data

We re-analyse the non-standard interaction (NSI) solutions to the solar neutrino problem in the light of the latest solar as well as atmospheric neutrino data. The latter require oscillations (OSC), while the former do not. Within such a three-neutrino framework the solar and atmospheric neutrino sectors are connected not only by the neutrino mixing angle theta(13) constrained by reactor and atmospheric data, but also by the flavour-changing (FC) and non-universal (NU) parameters accounting for the solar data. Since the NSI solution is energy-independent the spectrum is undistorted, so that the global analysis observables are the solar neutrino rates in all experiments as well as the Super-Kamiokande day-night measurements. We find that the NSI description of solar data is slightly better than that of the OSC solution and that the allowed NSI regions are determined mainly by the rate analysis. By using a few simplified ansatzes for the NSI interactions we explicitly demonstrate that the NSI values indicated by the solar data analysis are fully acceptable also for the atmospheric data. (C) 2002 Elsevier B.V. B.V. All rights reserved.