Influence of belt speed, grit sizes and pressure on the sanding of Eucalyptus grandis wood

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chemical properties and decay resistance of eucalyptus grandis wood from steamed logs

The objective of this study was evaluate the effect of the log steaming on the chemical properties and decay resistance of Eucalyptus grandis wood. Logs with diameter between 20 and 22 cm were studied. Half of logs were kept in its on original condition, and the other half was steamed at 90°C for 13 hours. The holocellulosc, Klason lignin, total extractives content and the weight loss caused by the decay fungus Pycnoporus sanguineous were characterized. The results showed that the log steaming of E. grandis wood cause: (l)a significantly decreased in holocellulose content; (2) an increase of 4.8% and 4.4% in total extractives and lignin content, respectively; and (3) a decrease in its durability against the decay fungus P. sanguineus in order of 13.03%. Copyright © (2012) by WCTE 2012 Committee.

Source-driven remobilizations of nutrients within stem wood in Eucalyptus grandis plantations

Nutrient remobilizations in tree ligneous components have been little studied in tropical forests. A complete randomized block design was installed in Brazilian eucalypt plantations to quantify the remobilizations of phosphorus (P), potassium (K), calcium (Ca), magnesium (Mg), and sodium (Na) within stem wood. Three treatments were studied: control with neither K nor Na addition (C), 3 kmol ha-1 K applied (+K), and 3 kmol ha-1 Na applied (+Na). Biomass and nutrient contents were measured in the stem wood of eight trees destructively sampled at 1, 2, 3 and 4 years after planting in each treatment and annual rings were localized on discs of wood sampled every 3 m in half of the trees. Chemical analyses and wood density measurements were performed individually for each ring per level and per tree sampled. Nutrient remobilizations in annual rings were calculated through mass balance between two successive ages. Our results show that nutrient remobilizations within stem wood were mainly source-driven. Potassium and Na additions largely increased their concentration in the outer rings as well as the amounts remobilized in the first 2 years after the wood formation. The amount of Na remobilized in annual rings was 15 % higher in +Na than in +K the fourth year after planting despite a 34 % higher production of stem wood in +K leading to a much higher nutrient sink. A partial substitution of K by Na in the remobilizations within stem wood might contribute to enhancing Eucalyptus grandis growth in K-depleted soils. © 2013 Springer-Verlag Berlin Heidelberg.

Behavior of the brown-rot fungus Gloeophyllum trabeum on thermally-modified Eucalyptus grandis wood

In this study, we aimed evaluate the behavior of the brown-rot fungus Gloeophylum trabeum and white-rot fungus Pycnoporus sanguineus on thermally-modified Eucalyptus grandis wood. To this end, boards from five-year-eleven-month-old E. grandis trees, taken from the Duratex-SA company stock, were thermally-modified between 180 ºC and 220 ºC in the Laboratory of Wood Drying and Preservation at Universidade Estadual Paulista - UNESP, Botucatu, Sao Paulo state Brazil. Samples of each treatment were tested according to the ASTM D-2017 (2008) technical norm. The accelerated decay caused by the brown-rot fungus G. trabeum was compared with the decay caused by the white-rot fungus P. sanguineus, studied by Calonego et al. (2010). The results showed that (1) brown-rot fungus caused greater decay than white-rot fungus; and (2) the increase in temperature from 180 to 220 ºC caused reductions between 28.2% and 70.0% in the weight loss of E. grandis samples incubated with G. trabeum.

Quality of wood and pulp from a clone of Eucalyptus grandis planted at three locations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Simulação em uso dos pisos de madeira de Eucalyptus sp e Corymbia maculata

A caracterização anatômica, física, mecânica e química da madeira fornece informações importantes para sua melhor utilização. Contudo, para que madeiras se tornem boa opção para o mercado de pisos, adicionalmente é necessária a realização de ensaios que simulem suas reais condições em serviço. Esses ensaios simulam o pisoteio executado pelos sapatos de salto com pequenas áreas de pressão, o arraste e a queda de objetos, a resistência à abrasão da superfície e o atrito oferecido durante o deslocamento de pessoas que caminham sobre ele. Grande dificuldade da seleção de novas madeiras para pisos está na ausência de valores de referência físico-mecânicos. O presente trabalho visou a caracterizar as madeiras de Eucalyptus clöeziana F. Muell, de Eucalyptus microcorys F. Muell e de Corymbia maculata Hook, para as propriedades de densidade básica, retratibilidade, aplicação de carga rolante, de atrito estático e dinâmico, endentação causada por cargas aplicadas em pequenas áreas, impacto da esfera de aço cadente e resistência à abrasão. Foi observado que as madeiras estudadas podem ser utilizadas para a confecção de pisos, de acordo com seus resultados obtidos e por meio de comparações com resultados de literatura.

Modificações na produtividade e nas características físicas e químicas da madeira de Eucalyptus grandis causadas pela adubação com lodo de esgoto tratado

O Eucalyptus grandis é uma das espécies mais cultivadas no Brasil devido à sua produtividade e qualidade da madeira. Avaliaram-se o efeito da aplicação de lodo de esgoto tratado (0 a 40 t ha-1 base seca) e uma dose de adubo mineral nos atributos físicos e químicos da madeira de Eucalyptus grandis de árvores com cinco anos de idade, no Município de Itatinga, São Paulo, Brasil. O tipo de solo foi caracterizado como Latossolo Vermelho-Amarelo Distrófico (argila = 120 g kg-1 na camada de 0-20 cm) e o clima, como mesotérmico úmido (Cwa), segundo a classificação de Köeppen. O delineamento experimental foi o de blocos ao acaso, com seis tratamentos e quatro repetições. O diâmetro à altura do peito (DAP), a altura das árvores e o volume de madeira foram obtidos em todas as parcelas de oito árvores com DAP na classe de maior freqüência. As caracterizações físicas e químicas da madeira foram realizadas de acordo com as normas da ABTCP, TAPPI e ABNT. O lodo de esgoto diminuiu a densidade básica da madeira, mas não afetou os teores de celulose, lignina, extrativos e o poder calorífico da madeira. O decréscimo de densidade da madeira pela adubação com lodo de esgoto foi compensado pela maior produtividade de madeira.

Viabilidade de aplicação da seleção precoce em testes clonais de Eucalyptus spp

Com o objetivo de avaliar a eficiência da seleção precoce em Eucalyptus spp. foram usados dados de dois testes clonais avaliados quanto ao crescimento em altura (ALT), diâmetro à altura do peito (DAP) e volume individual de madeira (VOL) aos 25, 50 e 72 meses de idade. O delineamento experimental nos dois testes clonais foi o de blocos casualizados, com trinta tratamentos (clones), seis repetições, sendo um deles com seis e o outro com dez plantas em linha por parcela, no espaçamento de 3,0 m x 3,0 m. Foi feita a análise de variância para cada caracter e idade. Foram obtidas as estimativas de coeficiente de determinação genotípico e de correlações genotípicas entre os caracteres nas idades juvenis e na idade de rotação. Para verificar a viabilidade da aplicação da seleção precoce, foi simulada a seleção de 30% dos clones nas idades juvenis e na idade de rotação para cada um dos caracteres e idades avaliadas, obtendo-se as estimativas de ganhos genéticos com a seleção direta e indireta. Houve diferenças significativas entre os clones avaliados nos dois experimentos para todos os caracteres e idades. Com base nos resultados obtidos, é possível efetuar a seleção precoce aos 2 anos de idade sobre o caracter DAP em testes clonais de eucalipto.

Influência da densidade básica da madeira de clones de Eucalyptus grandis x Eucalyptus urophylla na qualidade da polpa branqueada.

The study analyzed the wood basic density effect in two Eucalyptus grandis x Eucalyptus urophylla hybrid clones (440 kg/m(3) e 508 kg/m(3)) on bleached pulp quality (fiber dimensions and physical-mechanical properties). The woods performance on pulping, bleaching and beating results were analyzed. The Kraft pulping was carried out in forced circulation digester in order to obtain 17 +/- 1 kappa number targets. The pulps were bleached to 90 +/- 1 using delignification oxygen and D0EOPD1 bleaching sequence. Bleached pulp of low basic density clone showed, significantly, lowest revolutions number in the PFI mill to reach tensile index of 70 N.m/g, low Schopper Riegler degree and generated sheets with higher values to bulk and opacity. These characteristics and properties allow concluding that bleached pulp of low basic density clone was the most indicated to produce printing and writing sheets. The bleached pulp of high basic density clone showed higher values of bulk and capillarity Klemm and lower water retention value when analyzed without beating. The bleached pulp of high basic density clone showed more favorable characteristics to the production of tissue papers.

Propriedades físicas dos lenhos juvenil e adulto de Pinus elliottii Engelm var. elliottii e de Eucalyptus grandis Hill ex Maiden

The juvenile wood presents great difference in its anatomical and physical properties in relation to the mature wood. That heterogeneity of the wood causes a series of upset for the processing industry. The present research had as objective the study of the physical properties of the juvenile and mature wood of Pinus elliottii Engelm var. elliottii, with 25 years of age and of Eucalyptus grandis Hill ex Maiden, with 30 years of age, coming from the Experimental Station of Itapetininga and State Forest of Santa Barbara, belonging to the Forest Institute of the state of São Paulo. From both species there were taken from radial boards, specimens with dimensions of 20x30x50 mm, for the determination of density, swelling and swelling coefficient of the juvenile and mature wood. The results of the species showed that the mature compared with the juvenile wood presented: (1) an increase in the values of the basic density, at 0% and at 12% of moisture content and of the volumetric, radial and tangential swelling at 12% moisture content and maximum coefficient of radial and tangential swelling; (2) a reduction in the values of longitudinal swelling at 12% and maximum and of the longitudinal swelling coefficient.

Comportamento de adesão da madeira de um híbrido clonal de Eucalyptus urophylla x Eucalyptus grandis proveniente de três condições de manejo

This study aimed to evaluate the adhesion ability of eucalyptus lumber from three tillage systems, using adhesives: resorcinol formaldehyde and two adhesives in water emulsion based on vinyl poly-acetate. The management systems were characterized by three strata, the stratum one (E1) characterized by wood from coppice and 70 months of age, the stratum two (E2) characterized by wood and retirement age of 166 months and stratum three (E3), also characterized by retirement at 70 months of age. The wood was derived from a random mixture of the first two sawn logs, each three feet from the base, which comprised three treatments on the adhesive used. We evaluated the shear strength by compression tests and the percentage of wood failure in the glue line. Based on the results obtained, it can be said that the adhesion had satisfactory performance with all the resins used, and the average values of shear strength of the glue line were shown to be equivalent to the shear strength of solid wood only for the samples which adhered with 'Wonderbond' adhesive and also provide higher values for wood failure (97.64%). The highest density present in the wood of the second stratum (E2) influenced only sticking with the resorcinol formaldehyde resin. For polyvinyl acetate (Cascorez 2590), shear values decreased in the third management condition (E3).

Physical and mechanical properties of thermally modified wood from E. grandis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades físicas e mecânicas de painéis LVL de Eucalyptus grandis

This paper mainly aimed to evaluate the physical and mechanical properties of LVL panels made from Eucalyptus grandis, from reforestation at the region of Senges, in Parana state, Brazil. LVL panels were manufactured using 23 veneers (2,4mm thick each one) in commercial dimension of 2.500 mm long and 1,200 mm wide. The properties of static bending were analyzed (strength and rigidity) in beams of the LVL, in the flatwise and edgewise positions. The properties of compression parallel to grain and shear parallel in the plans L-X and L-Y and density in this LVL panels were also analyzed according to ASTM-D 5456/4761 and ASTM-D 198 codes. The mean values to flatwise bending MOE and MOR were 13114 MPa and 88.76 MPa, respectively, and for edgewise bending MOE and MOR were 15871 MPa and 88.63 MPa, respectively. The density (12%) of the LVL panels and of the veneers were 690 kg/m(3) and 649 kg/m(3). The mean values to parallel compression MOE and MOR were 16856 MPa and 58.05 MPa, respectively. The mean values of the maximum resistance to shear parallel in the plans L-X and L-Y were 5.96 MPa and 591 MPa, respectively. All these values reached partially or they passed the medium limits of reference (normative codes, researches and commercial catalogs) established for LVL panels and original solid wood, attesting overall the quality of those panels produced with this wood.

Selection of fungi for accelerated decay in stumps of Eucalyptus spp.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Can Eucalyptus invade native forest fragments close to commercial stands?

Some Eucalyptus species are widely used as a plantation crop in tropical and subtropical regions. One reason for this is the diversity of end uses, but the main reason is the high level of wood production obtained from commercial plantings. With the advancement of biotechnology it will be possible to expand the geographical area in which eucalypts can be used as commercial plantation crops, especially in regions with current climatic restrictions. Despite the popularity of eucalypts and their increasing range, questions still exist, in both traditional planting areas and in the new regions: Can eucalypts invade areas of native vegetation, causing damage to natural ecosystems biodiversity?The objective of this study it was to assess whether eucalypts can invade native vegetation fragments in proximity to commercial stands, and what factors promote this invasive growth. Thus, three experiments were established in forest fragments located in three different regions of Brazil. Each experiment was composed of 40 plots (1 m(2) each one), 20 plots located at the border between the forest fragment and eucalypts plantation, and 20 plots in the interior of the forest fragments. In each experimental site, the plots were paired by two soil exposure conditions, 10 plots in natural conditions and 10 plots with soil exposure (no plant and no litter). During the rainy season, 2 g of eucalypts seeds were sown in each plot, including Eucalyptus grandis or a hybrid of E. urophylla x E. grandis, the most common commercial eucalypt species planted in the three region. At 15, 30, 45, 90, 180, 270 and 360 days after sowing, we assessed the number of seedlings of eucalypts and the number of seedlings of native species resulting from natural regeneration. Fifteen days after sowing, the greatest number of eucalypts seedlings (37 m(-2)) was observed in the plots with lower luminosity and exposed soil. Also, for native species, it was observed that exposed soil improved natural germination reaching the highest number of 163 seedlings per square meter. Site and soil exposure were the factors that have the greatest influence on seed germination of both eucalypt and native species. However, 270 days after sowing, eucalypt seedlings were not observed at any of the three experimental sites. The result shows the inability of eucalypts to adapt to condition outside of their natural range. However, native species demonstrated their strong capacity for natural regeneration in forest fragments under the same conditions where eucalypts were seeded. (C) 2011 Elsevier B.V. All rights reserved.