Determination of the oxygen and nitrogen interstitial diffusion coeficient in niobium by mechanical spectroscopy

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermodynamic analysis of direct steam reforming of ethanol in molten carbonate fuel cell

Fuel cell as molten carbonate fuel cell (MCFC) operates at high temperatures. Thus, cogeneration processes may be performed, generating heat for its own process or for other purposes of steam generation in the industry. The use of ethanol is one of the best options because this is a renewable and less environmentally offensive fuel, and is cheaper than oil-derived hydrocarbons, as in the case of Brazil. In that country, because of technical, environmental, and economic advantages, the use of ethanol by steam reforming process has been the most investigated process. The objective of this study is to show a thermodynamic analysis of steam reforming of ethanol, to determine the best thermodynamic conditions where the highest volumes of products are produced, making possible a higher production of energy, that is, a more efficient use of resources. To attain this objective, mass and energy balances were performed. Equilibrium constants and advance degrees were calculated to get the best thermodynamic conditions to attain higher reforming efficiency and, hence, higher electric efficiency, using the Nernst equation. The advance degree (according to Castellan 1986, Fundamentos da Fisica/Quimica, Editora LTC, Rio de Janeiro, p. 529, in Portuguese) is a coefficient that indicates the evolution of a reaction, achieving a maximum value when all the reactants' content is used of reforming increases when the operation temperature also increases and when the operation pressure decreases. However, at atmospheric pressure (1 atm), the advance degree tends to stabilize in temperatures above 700 degrees C; that is, the volume of supplemental production of reforming products is very small with respect to high use of energy resources necessary. The use of unused ethanol is also suggested for heating of reactants before reforming. The results show the behavior of MCFC. The current density, at the same tension, is higher at 700 degrees C than other studied temperatures such as 600 and 650 degrees C. This fact occurs due to smaller use of hydrogen at lower temperatures that varies between 46.8% and 58.9% in temperatures between 600 and 700 degrees C. The higher calculated current density is 280 mA/cm(2). The power density increases when the volume of ethanol to be used also increases due to higher production of hydrogen. The highest produced powers at 190 mA/cm(2) are 99.8, 109.8, and 113.7 mW/cm(2) for 873, 923, and 973 K, respectively. The thermodynamic efficiency has the objective to show the connection among operational conditions and energetic factors, which are some parameters that describe a process of internal steam reforming of ethanol.

Pressure drop correlation for oil-refrigerant R134a mixture flashing flow in a small diameter tube

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of the photoinduced birefringence and of the refractive index by Brewster method of epoxy resin doped with CdS

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Association of diabetes and cigarette smoke exposure on the glycemia and liver glycogen of pregnant Wistar rats

Purpose: To evaluate cigarette smoke exposure and/or diabetes association effects on the glycemia and liver glycogen levels of pregnant Wistar rats. Methods: 60 adult rats were randomly distributed into (n= 10/group): non-diabetic exposed to filtered air (G1); non-diabetic exposed to cigarette smoke only before pregnancy (G2); non-diabetic exposed to cigarette smoke before and during pregnancy (G3); diabetic exposed to filtered air (G4); diabetic exposed to cigarette smoke only before pregnancy (G5), and diabetic exposed to cigarette smoke before and during pregnancy (G6). Glycemia was determined at days 0 and 21 of pregnancy. Liver samples were collected for liver glycogen determinations. Results: At day 21 of pregnancy, glycemia was higher in G5 and G6 compared to G4 group. G2 (2.43 +/- 0.43), G3 (3.20 +/- 0.49), G4 (2.62 +/- 0.34), G5 (2.65 +/- 0.27) and G6 groups (1.94 +/- 0.35) presented decreased liver glycogen concentrations compared to G1 (4.20 +/- 0.18 mg/100mg liver tissue) (p<0.05). G5 and G6 groups presented decreased maternal weight gain and litter weight. Conclusions: Severe diabetes and cigarette smoke exposure, alone or associated, caused impairment in liver glycogen storage at term pregnancy. Due to the fact that liver glycogen storages were considered determinant for glucose tolerance, it is relevant to point out a rigid clinical glycemic control and to stop smoking so earlier in pregnancy programming.

Relação entre a esfericidade, a função ventricular e o tamanho do infarto em ratos

FUNDAMENTO: A esfericidade do ventrículo esquerdo (VE) é fator associado com disfunção ventricular, mas não está bem caracterizada no modelo de ratos infartados. OBJETIVO: Analisar a relação entre o índice de esfericidade, a função ventricular e a área infartada no modelo experimental em ratos. MÉTODOS: Seis meses após infarto (IAM, n=33) ou cirurgia simulada (SHAM, n=18), os animais foram submetidos a ecocardiograma. O índice de esfericidade foi obtido pela razão entre as áreas diastólicas nos eixos maior e menor do VE. RESULTADOS: O grupo IAM apresentou menor índice de esfericidade (1,32 × 0,23 vs 1,57 × 0,33; p=0,002), de função sistólica e espessura relativa (0,13 × 0,003 vs 0,18 × 0,04; p<0,001) e maior índice de estresse parietal (1,27 × 0,33 vs 0,88 × 0,25; p<0,001). Houve correlação significativa entre tamanho do infarto e esfericidade (p=0,046). Na análise de regressão linear, o tamanho de infarto (p=0,014), mas não a esfericidade (p=0,683) e o estresse parietal (p=0,176), foi fator de predição da função sistólica. Remodelação excêntrica (p=0,011), mas não a esfericidade (p=0,183) ou o tamanho de infarto (p=0,101), foi fator preditor do estresse parietal. Adicionalmente, o tamanho do infarto (p=0,046), mas não remodelação excêntrica (0,705), foi fator preditor da esfericidade. O tamanho do infarto (p=0,015) e o estresse parietal (p=0,011), mas não a esfericidade (p=0,705), foram preditores de remodelação excêntrica. CONCLUSÃO: A esfericidade está associada mas não é fator determinante do estresse parietal, da remodelação excêntrica e da função sistólica ventricular no modelo de infarto experimental em ratos.

Cytokines released from blood monocytes and expressed in mucocutaneous lesions of patients with paracoccidioidomycosis evaluated before and during trimethoprim-sulfamethoxazole treatment

Background Mucocutaneous lesions in paracoccidioidomycosis are granulomatous and result from tissue responses to Paracoccidioides brasiliensis, the aetiological agent.Objectives and methods In this study we investigate the expression of tumour necrosis factor (TNF)-alpha, interleukin (IL)-10 and transforming growth factor (TGF)-beta 1 by immunohistochemistry in skin and mucosa lesions from patients with the chronic form of paracoccidioidomycosis, evaluated before and at day 20 of trimethoprim-sulfamethoxazole treatment. Cytokine production by peripheral blood monocytes was also studied by enzyme immunoassay.Results Intense immunostaining for TNF-alpha was detected in mononuclear cells that infiltrated granulomas in all skin and mucosa lesions before treatment simultaneously with low IL-10 granular deposits in these cells. At day 20 of treatment, there was reduced TNF-alpha and IL-10 deposition. Immunoreactive TGF-beta 1 was observed diffusely in the dermis and generally in the cytoplasm of macrophages and giant cells, before treatment, and as increased TGF-beta 1 deposits in the fibrosis area at day 20 of treatment. Peripheral blood monocytes from patients with paracoccidioidomycosis, evaluated before treatment, produced high endogenous levels of TNF-alpha, TGF-beta 1 and IL-10 in relation to healthy controls. Lipopolysaccharide-stimulated monocytes from patients secreted lower levels of TNF-alpha in both periods of evaluation while no impairment in capacity of IL-10 and TGF-beta production was observed.Conclusions Trimethoprim-sulfamethoxazole therapy was effective in decreasing fungal load in the lesions, allowing patient immune response to control the infection leading to the healing of the lesions.

Influence of glycemic control on fetal lung maturity in gestations affected by diabetes or mild hyperglycemia

Objective. To evaluate the influence of glycemic control on fetal lung maturity in pregnancies affected by diabetes or mild hyperglycemia. Design. Cross-sectional study. Setting. Level III maternity center. Population. A total of 187 pregnant women were submitted to routine amniocentesis for the assessment of fetal lung maturity up to 72 hours before delivery. Methods. Fetal lung maturity thresholds were: Clements-positive at a dilution of 0.5; OD(650) nm >= 0.15; and lamellar body count (LBC) >= 32,000/mu l. The relation of test results with adequate (<= 6.7 mmol/l) or poor (> 6.7 mmol/l) glycemic mean (GM) at term and at preterm was evaluated. Main outcome measure. Delay in fetal lung maturity when glycemic control was poor. Results. Glycemic control was adequate in 146 (78.1%) women. Clements maturity rates were higher at term (91.9%) than at preterm (64.7%) when GM <= 6.7 mmol/l (p < 0.001), but not when control was inadequate. LBC median was higher at term (99.0; 62.0-154.0) than at preterm (66.5; 40.5-108.25) (p = 0.009) when GM <= 6.7 mmol/l, while GM > 6.7 mmol/l did not lead to any difference between these rates at term or preterm. When glycemic control was adequate, OD(650) nm medians at term and at preterm were similar. However, when GM > 6.7 mmol/l, OD(650) nm median at term (0.29; 0.22-0.40) was higher than that observed at preterm (0.15; 0.12-0.18) (p < 0.001). Conclusions. Our results suggest that in term pregnancies routine amniocentesis for the assessment of fetal lung maturity should be abandoned. In preterm pregnancies, or when glycemic control is inadequate it is recommended.

Fator necrosante citotóxico em Escherichia coli isolada de mastite clínica bovina

This report describes the production of cytotoxic necrotizing factor (CNF) by an Escherichia coli strain isolated from clinical bovine mastitis with clinical signs of toxemia The animal had hemorrhages and necrosis of the mammary glands, and died within 24 hours after the onset of clinical signs. In addition to CNF identification, alpha-haemolysin and siderophores production were also characterized in this strain. This report reinforce the association of CNF and alpha-haemolysin production in E. coli virulence associated with clinical cases of severe bovine mastitis.

Energy and amino acid content in phase 1 nursery diet: piglet performance and body chemical composition

Avaliaram-se os efeitos da densidade de energia metabolizável (EM) e lisina digestível (LIS) sobre o desempenho e a composição corporal de leitões após o desmame. Utilizaram-se 114 animais desmamados aos 7,4 ± 0,80 kg; desses animais, 108 foram alojados na unidade de creche e 6 foram abatidos no dia do desmame para determinação dos dados comparativos da composição química corporal. Seis densidades de nutrientes foram estipuladas a partir de estudo anterior, com base na maior retenção de nitrogênio, mantendo-se as seguintes relações EM:LIS nas dietas experimentais: 3.390:1,291; 3.450:1,409; 3.650:1,411; 3.780:1,461; 3.940:1,507; e 4.109 kcal/kg EM:1,564% LIS. As dietas experimentais foram oferecidas durante 13 dias, quando os leitões atingiram o peso de 12,986 ± 1,449 kg. Avaliaram-se os prováveis efeitos residuais da densidade nutricional no desempenho subseqüente dos leitões. Ao término da fase inicial-1, seis leitões de cada densidade foram abatidos para determinação da composição química nas frações corporais e no corpo vazio. Não houve influência significativa dos níveis nutricionais no desempenho dos leitões ao término da avaliação. Os resultados de conversão alimentar e composição corporal ratificam o nível indicado em estudo anterior, de 4 g LIS/Mcal. O aumento da densidade de energia e lisina confirma a necessidade da correta relação entre ambos para assegurar o melhor desempenho dos leitões na fase inicial de crescimento.

Analysis of the healing process in delayed tooth replantation after root canal filling with calcium hydroxide, Sealapex and Endofill: a microscopic study in rats

The major concern in the therapeutics of tooth replantation refers to the occurrence of root resorption and different approaches have been proposed to prevent or treat these complications. The purpose of this study was to evaluate tissue response to delayed replantation of anterior rat teeth treated endodontically using calcium hydroxide, Sealapex, and Endofill without the placement of gutta-percha cones. Thirty rats had their right upper incisor extracted and maintained in dry storage for 60 min. After removal of the dental papilla, enamel organ, pulp tissue, and periodontal ligament remnants, the teeth were immersed in 2% sodium fluoride phosphate acidulated, pH 5.5, for 10 min. The root canals were dried with absorbent paper points and the teeth were assigned to three groups (n = 10) according to the filling material. Group I - calcium hydroxide and propyleneglycol paste, Group II - Sealapex, and Group III - Endofill. The sockets were irrigated with saline and the teeth were replanted. Replacement resorption, inflammatory resorption and ankylosis were observed in all groups. Although the occurrence of inflammatory resorption was less frequent in Group I, there were no statistically significant differences among the groups. It may be concluded that compared to the paste, filling the root canals with Sealapex and Endofill sealers without the placement of gutta-percha cones did not provide better results.

Finite Element Analysis to Compare Complete Denture and Implant-Retained Overdentures With Different Attachment Systems

This finite element analysis compared stress distribution on complete dentures and implant-retained overdentures with different attachment systems. Four models of edentulous mandible were constructed: group A (control), complete denture; group B, overdenture retained by 2 splinted implants with bar-clip system; group C, overdenture retained by 2 unsplinted implants with o'ring system; and group D, overdenture retained by 2 splinted implants with bar-clip and 2 distally placed o'ring system. Evaluation was performed on Ansys software, with 100-N vertical load applied on central incisive teeth. The lowest maximum general stress value (in megapascal) was observed in group A (64.305) followed by groups C (119.006), D (258.650), and B (349.873). The same trend occurred it) supporting tissues with the highest stress value for cortical bone. Unsplinted implants associated with the o'ring attachment system showed the lowest maximum stress values among all overdenture groups. Furthermore, o'ring system also improved stress distribution when associated with bar-clip system.

Influence of Different Ceramics on Resin Cement Knoop Hardness Number

This study evaluated: 1) the effect of different ceramics on light attenuation that could affect microhardness, measured as the Knoop Hardness Number (KHN), of a resin cement immediately and 24 hours after polymerization and 2) the effect of different activation modes (direct light-activation, light activation through ceramics and chemical activation) on the KHN of a resin cement.Resin cement Rely X ARC (3M ESPE) specimens 5.0 mm in diameter and 1.0 nun thick were made in a Teflon mold covered with a polyester film. The cement was directly light activated for 40 seconds with an XL 2500 curing unit (3M ESPE) with 650 mW/cm(2), light activated through ceramic discs of Duceram Plus (DeguDent), Cergogold (DeguDent), IPS Empress (Ivoclar), IPS Empress 2 (Ivoclar), Procera. (NobelBiocare), In Ceram Alumina (Vita) and Cercon (DeguDent), having a 1.2 mm thickness or chemically activated without light application. The resin cement specimens were flattened, and KHN was obtained using an HMV 2 microhardness tester (Shimadzu) with a load of 50 g applied for 15 seconds 100 pin from the irradiated surface immediately and after storage at 37 degrees C for 24 hours. Ten measurements were made for each specimen, with three specimens for each group at each time. The data were submitted to ANOVA and Tukey's test (p=0.05). The KHN of the resin cement was not only affected by the mode of activation, but also by the post-activation testing time. The mean KHN of the resin cement for chemical activation and through all ceramics showed statistically significant lower values compared to direct activation immediately and at 24 hours. The KHN for 24 hours post-activation was always superior to the immediate post-activation test except with direct activation. The most opaque ceramics resulted in the lowest KHN values.

Microwave Denture Disinfection Versus Nystatin in Treating Patients with Well-Controlled Type 2 Diabetes and Denture Stomatitis: A Randomized Clinical Trial

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)