Foto seleção de mielomas e hibridomas murinos na produção de anticorpos monoclonais

Pós-graduação em Pesquisa e Desenvolvimento (Biotecnologia Médica) - FMB

Análise de aminas aromáticas em amostras de interesse ambiental por cromatografia líquida de alta eficiência acoplada a detectores de arranjo de diodo, eletroquímico e espectrometria de massas: Thiago Mescoloto Lizier. -

Pós-graduação em Química - IQ

Desenvolvimento de equipamento multifuncional portátil de baixo custo para determinações fotométricas, turbidimétricas, nefelométricas e fluorimétricas

Pós-graduação em Química - IQ

Estudo de controladores aplicados a inversores para UPS com operação ilhada

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Conversor para pulsos elétricos de alta tensão, de curta duração, para processos de geração de ozônio

Pós-graduação em Engenharia Elétrica - FEIS

Sistemas autônomos de iluminacão pública em corrente contínua

Pós-graduação em Engenharia Elétrica - FEIS

Light-curing Time and Aging Effects on the Nanomechanical Properties of Methacrylate- and Silorane-based Restorations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Streptococcus Mutans Photoinactivation by Combination of Short Exposure of a Broad-Spectrum Visible Light and Low Concentrations of Photosensitizers

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Infrared LED irradiation photobiomodulation of oxidative stress in human dental pulp cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Time reduction of light curing: Influence on conversion degree and microhardness of orthodontic composites

Introduction: The aim of this study was to assess the influence of curing time and power on the degree of conversion and surface microhardness of 3 orthodontic composites. Methods: One hundred eighty discs, 6 mm in diameter, were divided into 3 groups of 60 samples according to the composite used-Transbond XT (3M Unitek, Monrovia, Calif), Opal Bond MV (Ultradent, South Jordan, Utah), and Transbond Plus Color Change (3M Unitek)-and each group was further divided into 3 subgroups (n = 20). Five samples were used to measure conversion, and 15 were used to measure microhardness. A light-emitting diode curing unit with multiwavelength emission of broad light was used for curing at 3 power levels (530, 760, and 1520 mW) and 3 times (8.5, 6, and 3 seconds), always totaling 4.56 joules. Five specimens from each subgroup were ground and mixed with potassium bromide to produce 8-mm tablets to be compared with 5 others made similarly with the respective noncured composite. These were placed into a spectrometer, and software was used for analysis. A microhardness tester was used to take Knoop hardness (KHN) measurements in 15 discs of each subgroup. The data were analyzed with 2 analysis of variance tests at 2 levels. Results: Differences were found in the conversion degree of the composites cured at different times and powers (P < 0.01). The composites showed similar degrees of conversion when light cured at 8.5 seconds (80.7%) and 6 seconds (79.0%), but not at 3 seconds (75.0%). The conversion degrees of the composites were different, with group 3 (87.2%) higher than group 2 (83.5%), which was higher than group 1 (64.0%). Differences in microhardness were also found (P < 0.01), with lower microhardness at 8.5 seconds (35.2 KHN), but no difference was observed between 6 seconds (41.6 KHN) and 3 seconds (42.8 KHN). Group 3 had the highest surface microhardness (35.9 KHN) compared with group 2 (33.7 KHN) and group 1 (30.0 KHN). Conclusions: Curing time can be reduced up to 6 seconds by increasing the power, with a slight decrease in the degree of conversion at 3 seconds; the decrease has a positive effect on the surface microhardness.

Healing of normal and osteopenic bone with titanium implant and low-level laser therapy (GaAlAs): a histomorphometric study in rats

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Assessment of the breakdown products of solar/UV induced photolytic degradation of food dye tartrazine

The food dye tartrazine (CI 19140) was exposed to UV irradiation from an artificial source, a mercury vapor lamp, and a natural one, sunlight. It was observed that conditions such as energy dose, irradiation time, pH and initial dye concentration affected its discoloration. There was 100% of color removal, after 30 min of irradiation, when a dye solution 1 x 10(-5) mol L-1 was submitted to an energy dose of 37.8 J cm(-2). Liquid Chromatography coupled to Diode Array Detection and Mass Spectrometry confirmed the cleavage of the chromophore group and the formation of five by-products at low concentration. Although by-products were formed, the Salmonella/microsome mutagenicity assay performed for both, the dye solution at a dose of 5.34 mg/plate and the solutions obtained after exposure to UV irradiation, did not present mutagenic activity for TA98 and TA100 with and without S9. (C) 2014 Elsevier Ltd. All rights reserved.

Effects of low-level laser therapy on the proliferation and apoptosis of gingival fibroblasts treated with zoledronic acid

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

HPLC-DAD method for metabolic fingerprinting of the phenotyping of sugarcane genotypes

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Flavonoid Detection in Hydroethanolic Extract of Pouteria torta (Sapotaceae) Leaves by HPLC-DAD and the Determination of Its Mutagenic Activity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)