Characterization of a wollastonite glass-ceramic material prepared using sugar cane bagasse ash (SCBA) as one of the raw materials

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Study of ceramic block manufacture with the addition of waste from iron ore extraction

This work is intended to study the possibility of adding an amount of waste from iron mining in the ceramic mass. Clay and coal, from Vale do Paraiba, Sao Paulo, Brazil, were used in this research. These raw materials are used in the ceramic block manufacture. Clay and waste were analyzed by X-ray fluorescence and X-ray diffraction, particle size, differential thermal and thermogravimetric analysis. Liquid limit and plasticity index tests were performed in order to determine the amount of waste that which should be used in the ceramic mass. After determining the amount of waste, all samples were uniaxially pressed and sintered at 900 degrees C. Surface roughness measurements, apparent porosity and bulk density technique and three-point flexural tests were also performed to characterize the samples. The results showed that by adding the exact amount of waste, which was determined by the essays, it is possible to manufacture solid bricks.

Evaluation of the shear bond strength of the union between two CoCr-alloys and a dental ceramic

Introduction: Based on the importance of the integrity of the metal/ceramic interface, the purpose of this work was to evaluate the shear bond strength of the metal-ceramic union of two Co-Cr alloys (Wirobond C, Bego; Remanium 2000, Dentaurum) combined with Omega 900 ceramic (Vita Zahnfabrik). Material and Method: Eleven cylindrical matrixes were made for each alloy, and the metallic portion was obtained with the lost wax casting technique with standardized waxing of 4mm of height and of 4mm of diameter. The ceramic was applied according to the manufacturer's recommendations with the aid of a teflon matrix that allowed its dimension to be standardized in the same size as the metallic portion. The specimens were submitted to the shear bond test in an universal testing machine (EMIC), with the aid of a device developed for such intention, and constant speed of 0.5mm/min. Results and Conclusions: The mean resistance was 48.387MPa for Wirobond C alloy, with standard deviation of 17.718, and 55.956MPa for Remanium 2000, with standard deviation of 17.198. No statistically significant difference was observed between the shear strength of the two metal-ceramic alloys.

Study of thermocycling effect on the bond strength between an aluminous ceramic and a resin cement

This study evaluated the effect of thermocycling on the bond strength between Procera AllCeram (Nobel-Biocare) and a resin cement (Panavia F, Kuraray CO). Nine ceramic blocks with dimensions of 5x6x6mm were conditioned at one face with Rocatec System (Espe). After, they were luted with Panavia F to composite resin blocks (Clearfil AP-X, Kuraray CO). The nine groups formed by ceramic, cement and composite resin were split up obtaining 75 samples with dimensions of 12x1x1mm and adhesive surface presenting 1mm2±0.1mm2 of area. The samples were divided into 3 groups (n=25): G1 - 14 days in distilled water at 37ºC; G2 – 6,000 cycles in water (5ºC - 55ºC – 30s); G3 – 12,000 cycles in water (5ºC - 55ºC – 30s). The samples were tested in a universal testing machine (EMIC) at a crosshead speed of 1mm/min. Data were analyzed by ANOVA and Tukey tests. The results indicated that mean values of rupture tension (MPa) of G1 (10.71 ± 3.54) did not differ statistically (p <5%) from G2 (9.01 ± 3.90), however there was statistical difference between G1 and G3 (7.28 ± 3.00). It was concluded that thermocycling significantly reduced the bond strength values when samples were submitted to 12,000 cycles.

The importance of the lifelike esthetic appearance of all-ceramic restorations on anterior teeth

The success of rehabilitation will not depend on just clinical procedures. A proper dental technique (ceramist) is required as well as the respect for some biomimetic principles to obtain the desired final result. This study has the purpose of describing a prosthetic rehabilitation with laminate veneers and all-ceramic crowns of a patient unsatisfied with a previous esthetic treatment because of the negligence of some biomimetic principles. A 45-year-old female patient was admitted to the dental clinic complaining about the lifelike appearance of her all-ceramic restorations. Before the fabrication of new restorations, a mock-up was conducted to verify the patient's satisfaction. A ceramist conducted all the fabrication process so that surface characterizations could be visually verified and the lifelike appearance of natural tooth could be reproduced. After the cementation procedure, the patient reported being satisfied with the lifelike appearance of the new restorations. Based on the clinical findings of the present case report, it can be concluded that the reproduction of the lifelike esthetic appearance of natural teeth and the visualization of the final results before definitive procedures are essential to obtain the clinical success.

Bone Ceramic® at implants installed immediately into extraction sockets in the molar region: an experimental study in dogs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Oxygen mobility in Bi:Sr:Ca:Cu:O ceramic measured using anelastic relaxation methods

Since the discovery of YBaCuO, experiments have shown that its superconducting properties are strongly affected by the oxygen content. More recently, anelastic relaxation measurements in La2CuO4+δ, showed that the decrease in the oxygen content can be related to two events. One is the decrease in mobility between two adjacent CuO planes, and the other is the increase in the number of tilting patterns of the CuO6 octahedra. In the case of the bismuth-based ceramic, it is known that the oxygen content, within some limits, does not affect its superconducting properties. In order to evaluate the mobility and the effect of the oxygen content on this material we have prepared BSCCO ceramic and tested regarding its internal friction and electrical resistivity as a function of the temperature while the oxygen content was being reduced by a sequence of vacuum annelaing at 620 K. The samples were prepared in the Bi:Sr:Ca:Cu = 2212 and 2223 proportion, using powder obtained by the sol-gel route and conventional solid state reaction. The anelastic relaxation measurements were performed using a torsion pendulum operating with frequency about 15-35 Hz between 77 to 700 K. The diffraction pattern of the as sintered and the vacuum annealed material were also presented. The results have shown complex anelastic relaxation structures that were associated to the jump of interstitial oxygen atoms between two adjacent CuO planes. The vacuum annealing showed to be deleterious to the critical temperature of the superconducting ceramic.

Efeito da infiltração de sílica pelo método sol-gel na resistência à flexão de bicamadas de porcelana e Y-TZP

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação dos preparos da superfície cerâmica para a colagem de acessórios ortodônticos

The purpose of this study was to evaluate the effects of two conditioning methods used to enhance the shear strength of orthodontic brackets bonded to porcelain surfaces. A total of 18 feldspathic specimens were used. The specimens were divided randomly into two groups (n = 9): group free silane, the porcelain specimens were etched with hidrofuoric acid 10% (Acid Gel-Maquira) for 4 minutes followed by adhesive-primer (Transbond XT) and the metallic brackets (Morelli Roth Light .022" x .030") were bonded with a light-cured microfilled resin (Transbond XT Light Cure Orthodontic Adhesive); group silane, the porcelain specimens were etched with hidrofuoric acid 10% (Acid Gel-Maquira) for 4 minutes followed by silane (Silano Ângelus) for 1 minute, adhesive-primer (Transbond XT) and the metallic brackets (Morelli Roth Light .022" x .030") were bonded with a light-cured microfilled resin (Transbond XT Light Cure Orthodontic Adhesive). All specimens were stored in solution of artificial saliva at ambient temperature for 24 hours. The debonding was done with shear strength through a universal testing machine (DL 500-Emic) calibrated with a fixed speed of 1mm/minute. Statical analysis was performed using the Student t test. The results indicated that in the free silane group the mean bond strength was 9,97 MPA, significantly lower than the silane group, that was 12,38 MPa (p < 0,05). The both groups were effective for bonding, although the silane group had the highest bond strength values.

Bond strength and Raman analysis of the zirconia-feldspathic porcelain interface

The test groups were experimental zirconia, Zirkonzahn zirconia, and Schuetz zirconia. Blocks of partially sintered zirconia were cut into disks (n=20) and then veneered with a feldspathic porcelain. Half of the specimens from each group (n=10) were incubated in 37°C water for 24 hours, and the other half were thermocycled. All the specimens were then subjected to shear testing. The fractured areas were analyzed with optical stereomicroscopy and classified as adhesive, cohesive, or an adhesive-cohesive failure. Spectral patterns were examined to detect bands related to the zirconia and feldspathic porcelain phases. The shear strength data were submitted to 2-way ANOVA. Results No significant differences in shear bond strength were observed among the 3 groups, regardless of whether or not the specimens were thermocycled. Adhesive failures were the most prevalent types of failure (70%). Raman spectra were clearly distinguished for all the materials, which showed the presence of tetragonal and monoclinic phases. Conclusions The controlled production of the experimental zirconia did not influence the results of the bond strength. Raman analysis suggested a process of interdiffusion by the presence of peaks associated with the zirconia and feldspathic ceramics.

Reação de clones de umezeiro (Prunus mume sieb. et zucc.) e cultivares de pessegueiro a Meloidogyne javanica (treub, 1885) Chitwood, 1949

Um amplo projeto de estudos sobre a utilização do umezeiro como porta-enxerto para pessegueiro está sendo desenvolvido na FCAV/UNESP, Câmpus de Jaboticabal-SP, devido, especialmente, às promissoras características para uso como redutor de vigor da copa e sua boa qualidade de frutos. Alguns trabalhos na literatura citam o umezeiro como resistente ao nematóide das galhas, entretanto dispõe-se de poucas informações. Neste trabalho, teve-se por objetivo estudar a reação de clones de umezeiro e cultivares de pessegueiro a Meloidogyne javanica. O experimento foi conduzido em casa de vegetação, com 6 tratamentos (Clones 05; 10 e 15 de umezeiro e as cultivares Okinawa, Aurora-1 e Dourado-1 de pessegueiro) e 9 repetições. As plantas foram mantidas em vasos de cerâmica contendo uma mistura de solo e areia (1:1, v/v), previamente autoclavada a 121ºC e 1kgf.cm-2 por 2 horas. Aos sessenta dias após o plantio, cada planta foi inoculada com 3.000 ovos e juvenis de segundo estádio de Meloidogyne javanica. Aos 100 dias após a inoculação, as plantas foram colhidas para avaliação da massa de matéria fresca do sistema radicular, número de galhas por sistema radicular, número de ovos e juvenis por 10 g de raízes, número de ovos e juvenis por sistema radicular e fator de reprodução. Verificou-se que todos os clones e cultivares de umezeiro e pessegueiro, respectivamente, mostraram-se resistentes a Meloidogyne javanica.

Resistência de clones de umezeiro e cultivares de pessegueiro a Meloidogyne incognita (nemata: Heteroderidae)

O presente estudo teve por objetivo avaliar a reação dos Clones 05; 10 e 15 de umezeiro (Prunus mume Sieb. et Zucc.) e das cultivares Okinawa, Aurora-1 e Dourado-1 de pessegueiro [Prunus persica (L.) Batsch] a Meloidogyne incognita (Kofoid and White) Chitwood, em condições de casa de vegetação. As plantas foram mantidas em vasos de cerâmica contendo uma mistura de solo e areia (1:1, v/v), previamente autoclavada a 121ºC e 1kgf.cm-2 por 2 horas. Aos 60 dias após o plantio, cada planta foi inoculada com 2.000 ovos e juvenis de segundo estádio de Meloidogyne incognita. O experimento foi conduzido em delineamento inteiramente casualizado, com 6 tratamentos (genótipos) e 9 repetições. Transcorridos 116 dias após a inoculação, as plantas foram colhidas para avaliação do sistema radicular. Foi possível verificar que o número de galhas por sistema radicular, o número de ovos e juvenis por 10g de raízes e por sistema radicular foi nulo ou praticamente nulo em todos os clones e nas cultivares estudadas, de forma que os respectivos fatores de reprodução foram todos inferiores a 1. Conclui-se que os Clones 05; 10 e 15 de umezeiro, assim como as cultivares Okinawa, Aurora-1 e Dourado-1 de pessegueiro são resistentes a Meloidogyne incognita.

Reação de clones de umezeiro (Prunus mume Sieb. et Zucc.) e cultivares de pessegueiro [Prunus persica (L.) Batsch] ao nematóide anelado Mesocriconema xenoplax (Nemata: Criconematidae)

Com o objetivo de avaliar a reação de clones de umezeiro (Prunus mume Sieb. et Zucc.) e cultivares de pessegueiro [Prunus persica (L.) Batsch] ao nematóide anelado Mesocriconema xenoplax (Raski) Loof & de Grise, realizou-se o presente estudo em casa de vegetação do Departamento de Fitossanidade da FCAV/UNESP, Câmpus de Jaboticabal-SP. As plantas foram mantidas em vasos de cerâmica com 6 litros de capacidade, contendo uma mistura de solo e areia (1:1, v/v), previamente autoclavada a 121°C e 1kgf.cm-2 por 2 horas. Cada planta foi inoculada com 10mL de uma suspensão de 200 M. xenoplax por mL. Com os resultados obtidos, após 105 dias da inoculação, pode-se concluir que os Clones 05; 10 e 15 de umezeiro e as cultivares Okinawa e Aurora-1 de pessegueiro são suscetíveis a M. xenoplax. A cultivar Aurora-1 apresentou maior Fator de Reprodução (93,06).

EFFECT of DIFFERENT SOLID AMOUNTS IN THE PHYSICAL and MICROSCOPICAL PROPERTIES of SiC POROUS CERAMICS

The presence of pores in ceramics is directly related to the chosen forming process. So, in the starch consolidation method, the ceramics show, after burning, pores with morphology similar to that presented by this organic material. on the other hand, the increase in solid load leads up to alterations in dispersion viscosity, increasing the thermal stresses during drying and sintering processes. In order to verify the solid percentage influence in ceramic final properties, samples were prepared with silicon carbide in different compositions using or not starch as binder agent and pore forming element. The characterization of the ceramic pieces was performed by superficial roughness measurements, porosity besides by optical and scanning electron microscopy. The results showed ceramics with SiC and starch presented physical and microscopic properties slightly higher in relation to those with only ceramic powder in their composition. The presence of organic material, agglomerated and foam during the forming were essential for the final properties of the studied samples.