Finite element analysis of the influence of geometry and design of zirconia crowns on stress distribution

Purpose: To evaluate the influence of the geometry and design of prosthetic crown preparations on stress distribution in compression tests, using finite element analysis (FEA). Materials and Methods: Six combinations of 3D drawings of all-ceramic crowns (yttria-stabilized zirconia framework and porcelain veneer) were evaluated: F, flat preparation and simplified crown; FC, flat preparation and crown with contact point; FCM, flat preparation and modified crown; A, anatomical preparation and simplified anatomical crown framework; AC, anatomical preparation and crown with contact point; and ACM, anatomical preparation and modified crown. Bonded contact types at all interfaces with the mesh were assigned, and the material properties used were according to the literature. A 200 N vertical load was applied at the center of each model. The maximum principal stresses were quantitatively and qualitatively analyzed. Results: The highest values of tensile stress were observed at the interface between the ceramics in the region under the load application for the simplified models (F and A). Reductions in stress values were observed for the model with the anatomical preparation and modified infrastructure (ACM). The stress distribution in the flat models was similar to that of their respective anatomical models. Conclusions: The modified design of the zirconia coping reduces the stress concentration at the interface with the veneer ceramic, and the simplified preparation can exert a stress distribution similar to that of the anatomical preparation at and near the load point, when load is applied to the center of the crown.

Effect of cryoprotectants on the reconstitution of silica nanoparticles produced by sol-gel technology

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of beta-cyclodextrin on the properties of norfloxacin form A

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Loss of desiccation tolerance in Copaifera langsdorffii Desf. seeds during germination

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Modeling the formation and propagation of desiccation cracks in soils

The problem of desiccation cracks in soils has received increasing attention in the last few years, in both experimental investigations and modeling. Experimental research has been mainly focused on the behavior of slurries subjected to drying in plates of different shapes, sizes and thickness. The main objectives of these studies were to learn about the process of crack formation under controlled environmental conditions, and also to better understand the effect of different factors (e.g. soil type, boundary conditions, soil thickness) on the morphology of the crack network. As for the numerical modeling, different approaches have been suggested lately to describe the behavior of drying cracks in soils. One aspect that it is still difficult to describe properly is the crack pattern observed in desiccated soils. This work presents a novel technique to model the behavior of drying soils. The crack patter observed in desiccation tests on circular plates are simulated with the main objective of predicting the effect of soil thickness on crack pattern. Good agreement between experimental results and model prediction are observed.

Quality of egg yolks after oxycarotenoids supplementation in hens' diets

Oxycarotenoids concentration in layer hens’ feed may be increased whenever the consumer market demands for more pigmented egg yolks. Oxycarotenoids present in Rubrivivax gelatinosus biomass grown in industrial wastewater have already proved their ability on enhancing yolk color. Moreover, there is a current interest on the antioxidant properties that some carotenoids may provide to food and health. So, in this experiment, we investigated the effects of oxycarotenoids supplementation in hens´ diets on yolk composition and stability to rancidity. Hy line hens aging 19 weeks were individually housed in wire cages equipped with feeders and drinkers. After 15 days receiving a corn basal diet nutritionally balanced, they were assigned to four different treatments, with six replicates, that lasted for 28 days: T1 – basal diet (control), T2 – basal diet + 1.5 mg/kg canthaxanthin, T3 – basal diet + 4.5 g/kg freeze dried R. gelatinosus biomass and T4 - basal diet + 4.5 g/kg spray dried R. gelatinosus biomass. Eggs laid on the last 5 days of rearing were collected; the yolks were separated, analyzed for pH and then freeze dried for the further analyses. Proximate composition was determined after drying and the rancidity (TBRAS method) was investigated at 0, 30 and 60 days of storage at room temperature/dark conditions. Yolks that received the oxycarotenoids had the lowest moisture content and the highest protein contents (P < 0.05). Lipids and pH were the same for all treatments (P > 0.05) and ashes only were higher for T2 (P < 0.05). All treatments that received oxycarotenoids had lower TBARS than control group and, among them, oxycarotenoids from spray dried R. gelatinosus biomass were the most effective to prevent rancidity (P < 0.05). So, we concluded that the use of R. gelatinosus biomass in hens feed brings positive effects to the yolk quality, since protein content is increased and conservation is increased due to decreased water content and lipid oxidation.

Monitoramento do tempo de prensagem e do comportamento da temperatura através da espessura de painéis LVL (Laminated veneer lumber)

The aim of this study was to analyze the behavior of the flow of heat (temperature) through the thickness of panels LVL (Laminated veneer lumber) produced with phenol formaldehyde adhesive, in laboratorial and industrial scales. Experimental program was conducted with five LVL panels (three produced in laboratorial scale and two in industrial scale) with different arrangements of a mix of commercial veneers from tropical pinus from the south region of Sao Paulo State, Brazil, bonded using phenol formaldehyde adhesive. The temperature inside the panels during the pressing process was evaluated using thermocouples type T (cooper-constantan), installed mostly in the center of the glue lines and connected to a data acquisition system. The graphics of temperature as a function of the time showed a gradual increase of temperature up to pre-set values, remaining constant from them. The temperature reached at the center of the panels was adequate to promote the curing of the adhesive. These pre-set values were similar to the minimum values presented by other authors and manufacturers of these adhesives that affirm that temperatures above 100ºC at the center of laminated panels bonded with phenolic adhesives are sufficient to ensure proper cure of the resin. The time necessary for curing of the adhesives confirmed the validity of practical expressions provided by adhesive manufacturers.