Análise de falhas por fadiga de alto ciclo em eixos de transmissão utilizando o método dos elementos finitos

This work presents a study that aims to validate the fatigue analyses developed on finite element commercial software, ANSYS Workbench. It was based on mechanical tests development of traction and hardness, to verify the mechanical properties of material that the shaft was manufactured (ABNT 1045 steel), it was developed bend test, with purpose to prove the confiability degree of computational analyses, obtaining the maximum stress in a work condition determined with 40 [kgf] of load applied, and at the end, was developed the fatigue test to obtain the number of cycles that the transmission shaft can support in a work condition with 8 [kgf] of load applied. The results obtained during the work present, have to be quite satisfactory with the theoretically expected

Estudo das propriedades mecânicas do aço SAE 1312 modificado ao nióbio

The study of mechanical properties of high-alloy special steels is of great interest of the steel industry due to the great demand by companies that manufacture automotive components of high criticality, and also because of its high commercial value. However, the development of this type of alloy metals demand highly technical knowledge. Among these extremely important kinds of steel, the subject which is the interest of this study is the special steel modified by niobium. The manganese and niobium are the main alloying elements in the composition of these steels, both of them increase the stability of the austenite region, however, manganese increases the hardenability and tensile yield strength, and niobium increases the mechanical strength and promotes refining the grain. The mechanical characterization of steel SAE 1312 modified the niobium was made in order to gain a better understanding of the influence on the mechanical properties caused by aging at different temperatures and for different reductions in the drawing of gauge material. This characterization was made by means of tensile test and hardness. This material showed an increase in yield strength and hardness when gauge with large reductions during the wiredrawing, but when subjected to aging temperatures higher than 300 ° C had a slight loss of these properties

Avaliação do efeito ambiental nas propriedades mecânicas e viscoelásticas de compósitos híbridos de titânio/fibra de carbono/resina epóxi

Hybrid composites combining metal plates and laminates with continuous fiber reinforced polymer, called fiber-metal (CHMF), have been particularly attractive for aerospace applications, due mainly to their high mechanical strength and stiffness associated with low density. These laminates (CHMF) consist of a sandwich structure consisting of layers of polymer composites and metal plates, stacked alternately. This setting allows you to combine the best mechanical performance of polymer composites reinforced with long fibers, to the high toughness of metals. Environmental effects should always be considered in the design of structural components, because these materials in applications are submitted to the effects of moisture in the atmosphere, the large cyclical variations of temperature around 82 ° C to -56 ° C, and high effort mechanical. The specimens of fibermetal composite were prepared at EMBRAER with titanium plates and laminates of carbon fiber/epoxy resin. This study aims to evaluate the effect of different environmental conditions (water immersion, hygrothermal chamber and thermal shock) of laminate hybrid titanium/carbon fiber/epoxy resin. The effects of conditioning were evaluated by interlaminar shear tests - ILSS, tensile, and vibration free

Análise do desempenho físico-mecânico de painéis compensados de Pinus sp. produzidos com adesivos aquosos a base de poliacetato de vinila e de homopolímero vinílico

This study aimed to evaluate the physico-mechanical performance of three PVA adhesive formulations according to the Brazilian standards for plywood testing and to evaluate the results with those presented in the technical literature and specified in normative documents. The study presents the production process of the panels, the obtaining of samples and, finally, the implementation of physico-mechanical characterization tests based on plywood Brazilian standards. For the panels production it was used a gramature of 120 g / m² and applied a pressure of 15 bars and two temperature combinations and pressing time for each adhesive. The commercial adhesives used were PVA 1810, PVA 1060 and Vinyltec 239. The physical tests conducted were thickness swelling, density, moisture content and water absorption. The mechanical tests were static flexion, for the determination of elasticity modulus (MOE) and rupture modulus (MOR), and shear in the glue line. Among the three formulations studied none showed good performance in the presence of water. However, other trials in the adhesive showed better results and closer to the commercially equivalent used, in the case the urea-formaldehyde, was the PVA 1810, that can be applied in non-structural uses and in environments without the presence of moisture

Regiões competitivas agrícolas e vulnerabilidade territorial: o papel do Consórcio Pesquisa Café

This academic work presents the final results of the undergraduate research about new agricultural technical systems developed by “Consórcio Pesquisa Café” (CPC), which main objective was to analyze the impacts of scientific inputs in different coffee producing regions, particularly in South of Minas Gerais. The creation of the CPC meets the demands of a global scientific coffee-growing (SANTOS, 2000) under development in the current period technical-scientific-informational (SANTOS, 2009). On this period, also called globalization, the technoscience, the information and the finances guide the actions of companies and institutions submitted by imperative of competitiveness on international market. The Brazilian’s coffee-growing regions (South of Minas Gerais, Cerrado Mineiro, Espírito Santos Ridge’s, Western Bahia, among others) on search of higher productivities, begin gather technical, informational and communicational densities (SANTOS, 2009). Considering these facts, we detail in this research, the major agricultural technical systems developed by “Consórcio Pesquisa Café” (CPC), expressed in new management techniques, new cultivars and new chemicals, mechanical and biological inputs. In the concluding part of this undergraduate research we analyze how these new technical systems contribute to increased competitiveness and vulnerability of South of Minas Gerais in front of international market

Estudo de falhas por fadiga em caldeiras

In recent years, increasing demand for energy has led to studies to increase the amount of electricity produced. Due to this fact, more and more boilers are becoming important sources of electricity generation. To raise the efficiency of energy generated in the boilers is necessary to raise the steam pressure and temperature to values previously unimaginable. The use of more resistant materials and maintenance practices and most appropriate operation made it possible. The objective of this study is to test the main types of failure in a chemical recovery boiler, in particular due to fatigue in the superheater, because it is a component subjected to high temperatures and thus more subject to different failures. In this manner this study aims to reduce the incidence of unscheduled maintenance shutdowns, increasing the operation time under appropriate conditions. Modeling performed in this study, the failure did not occur, because we considered only the mechanical stress. Under normal conditions, mechanical stress in combination with thermal stresses can cause cracks in the tubes due to cyclical stresses, leading to fatigue failure

Efeito do tratamento alcalino da fibra na resistência mecânica do compósito epóxi/capim-sapê

Due to growing concerns for reducing environmental damage caused by the use of non-renewable raw materials, there is a growing demand for research related to aggregate technology with environmental preservation. Thus, the use of non-renewable materials and less aggressive materials has been gaining attention. About composite materials, the exchange of synthetic fibers by natural fibers, especially vegetable fiber as reinforcement, has been increasing, due to its physical-chemical properties such as mechanical strength, nontoxic, low cost, low density, processing flexibility, non-abrasive to the process equipment, requiring simple surface treatments, etc. This objective was to process composites reinforced with long fibers of sapegrass in epoxy matrix and characterize the composites through mechanical tests. Three groups of composites were prepared according to the treatment received by the reinforcement: without treatment, alkali treatment at concentration of 5% w/v and alkali treatment at 10% w/v concentration. The materials were analyzed by tensile and flexural, and tests also optical microscopy and scanning electron microscopy (SEM). The results were statistically analyzed. As the main result, the alkali treatment of 5% in the sapegrass fibers increases the tensile and flexural strength, as a consequence of the improve adhesion between matrix and reinforcement

Análise microestrutural de tubos API N80 soldados pelo processo HF/ERW para prospecção de petróleo e gás

On the grounds of the great advances achieved over recent years, the process HF/ERW (High-Frequency/Electric Resistance Welding)welded pipe have played an active role in the oil and gas industry for deep water applications, at high and extremely low temperatures, under high pressure and in highly corrosive environments, gradually replacing manufactured pipes by other processes. However, studies have shown that defects in the welded joints are a the leading causes of pipelines failures, which has required the determination of toughness values in this region, in compliance with the strict recommendations of the codes and standards with manufacturers and construction companies, on the oil and gas sector. As part of the validation process required toughness values, this research project focuses on a microstructural analysis in HF / ERW tubes microalloyed, steel grade API 5CT N80, designed to explore oil and gas in deep waters, the subject of strategic relevance to the country because of the recent discoveries in the Santos mega fields: Tupi and Libra (pre-salt). In this scientific work will be presented and discussed the results of mechanical tensile and Charpy, a few CTOD tests curves (showing the trend of toughness values to be obtained), and the microstructures of the base material obtained by optical microscopy, with special emphasis on the formation of non-metallic inclusions in the welded joint

Estudo e aplicação de diferentes métodos de resolução para problemas dinâmicos não-lineares em presença de atrito

The friction phenomena is present in mechanical systems with two surfaces that are in contact, which can cause serious damage to structures. Your understanding in many dynamic problems became the target of research due to its nonlinear behavior. It is necessary to know and thoroughly study each existing friction model found in the literature and nonlinear methods to define what will be the most appropriate to the problem in question. One of the most famous friction model is the Coulomb Friction, which is considered in the studied problems in the French research center Laboratoire de Mécanique des Structures et des Systèmes Couplés (LMSSC), where this search began. Regarding the resolution methods, the Harmonic Balance Method is generally used. To expand the knowledge about the friction models and the nonlinear methods, a study was carried out to identify and study potential methodologies that can be applied in the existing research lines in LMSSC and then obtain better final results. The identified friction models are divided into static and dynamic. Static models can be Classical Models, Karnopp Model and Armstrong Model. The dynamic models are Dahl Model, Bliman and Sorine Model and LuGre Model. Concerning about nonlinear methods, we study the Temporal Methods and Approximate Methods. The friction models analyzed with the help of Matlab software are verified from studies in the literature demonstrating the effectiveness of the developed programming

Avaliação da influência do formato da porca e da pré-carga em juntas aparafusadas em tração

Many structures and mechanical equipment requires a union member, and the screw is one of the most used, the cost is low, it is versatile and easy to find on the market. The resulting pre-load assembly torque associated with the cyclical external load has great influence, so it will be studied carefully. This study analyzed some of these factors, as the format of nuts, and the washer material when they are incompatible with the bolt material can cause a reduction in life of the joint fatigue

Comportamentos, térmico e mecânico, de compósitos de polipropileno e resíduo da hidrólise enzimática do bagaço de cana de açúcar

Pós-graduação em Engenharia Mecânica - FEG

Estudo comparativo das madeiras de cecropia palmata (imbaúba) e eucalyptus grandis para produção de celulose e papel

Pós-graduação em Ciência Florestal - FCA

Obtenção e caracterização de compósitos nanoestruturados de poli(sulfeto de fenileno) reforçados com nanotubos de carbono

Pós-graduação em Engenharia Mecânica - FEG

Estudo da modificação superficial de fibras de carbono por meio de tratamentos a plasma para o aumento da adesão na interface de compósitos fibra de carbono/PPS

Pós-graduação em Engenharia Mecânica - FEG

Resistência à tração de coroas de NiCr cimentadas sobre munhões de liga de titânio, com 4 diferentes tipos de cimentos

In this work of tensile strength was evaluated the efficacy of 4 cements (S. S. White zinc phoshate, Ketac Cem Easymix glass ionomer, RelyX Luting 2 composite resin/glass ionomer and Panavia 21 TC special acrylic resin) used to fix NiCr crowns to usinated titanium alloy abutments. Were used 40 abutments distributed in groups of 10 elements, to each material. The mechanical essays were developed at a MTS 810 universal machine, adjusted to a 0.5 mm/m velocity. The ANOVA applied to data pointed out the existence of significant differences between groups; the subsequent Tukey´s test (p<0.05) also detected significant differences, except at comparisons of phosphate versus RelyX and phosphate versus Ketac Cem. The better performance was presented by Panavia 21 (1,127.996 N); RelyX (478.197 N) showed itself similar only to phosphate (430.662 N), wich had a performance similar to that of Ketac Cem (227.705 N).