Simulação numérica de fluxo de águas subterrâneas na bacia do Rio Corrente (BA)

The numeric simulation is an important tool applied in understanding the dynamics of groundwater flow. In a hydrogeological model the processes responsible for groundwater flow are described by numerical formulations that allow the simplification, representation and understanding of the dynamics of the Aquifer System. In this work, a steady state groundwater flow simulation of Urucuia Aquifer System (UAS) part of the Corrente river basin was conducted, using the finite element method through software FEFLOW, to understand the dynamics of groundwater flow and quantify the hydrologic balance. The aquifer system Urucuia lodges in the São Francisco hydrogeological province and corresponds to a set of interconnected aquifers that occur in rocks from Urucuia group in the Urucuia sub-basin described by Campos e Dardenne (1997). The system is a porous media one, in a shape of a thick table mountain, consisting essentially of sandstones. The Corrente river basin is located in UAS in Western State of Bahia and it's one of the main units to maintaining permanent flow (Q95) and average natural flow of the São Francisco river. The simulation performed in this work obtained the following results for the modelled region: horizontal hydraulic conductivity of 3 x 10-4 m/s and vertical one 6 x 10-5 m/s; maximum recharge of 345 mm and minimum of 85 mm/a. It was concluded that: (1) regional groundwater flow has eastbound; with an exception of the extreme northeast portion, where the flow has opposite direction; (2) there are smaller water side dividers with an approximate direction EW, that guide the flow of water to the drainage that cut the aquifer; and (3) the UAS at Corrente river basin can be understood as a free regional aquifer system, isotropic and homogeneous. Regionally, the small lithological variations present in the Urucuia group can be neglected and do not exhibit significant influences on the dynamics of ground water flow

Simulação numérica de fluxo de águas subterrâneas do aquífero Rio Claro, na região do campus da UNESP - Rio Claro, SP

The water management in any area is highly important to the success of many business and also of life and the understanding of your relationship with the environment brings better control to its demand. I.e. hydrogeological studies are needed under better understanding of the behavior of an aquifer, so that its management is done so as not to deplete or harm it. The objective of this work is the numerical modeling in transient regime of a portion of the Rio Claro aquifer formation in order to get answers about its hydrogeological parameters, its main flow direction and also its most sensitive parameters. A literature review and conceptual characterization of the aquifer, combined with field campaigns and monitoring of local water level (NA), enabled the subsequent construction of the mathematical model by finite elements method, using the FEFLOW 6.1 ® computational algorithm. The study site includes the campus of UNESP and residential and industrial areas of Rio Claro city. Its area of 9.73 km ² was divided into 318040 triangular elements spread over six layers, totaling a volume of 0.25 km³. The local topography and geological contacts were obtained from previous geological and geophysical studies as well as profiles of campus wells and SIAGAS / CPRM system. The seven monitoring wells on campus were set up as observation points for calibration and checking of the simulation results. Sampling and characterization of Rio Claro sandstones shows up a high hydrological and lithological heterogeneity for the aquifer formation. The simulation results indicate values of hydraulic conductivity between 10-6 and 10-4 m / s, getting the Recharge/Rainfall simulation in transient ratio at 13%. Even with the simplifications imposed on the model, it was able to represent the fluctuations of local NA over a year of monitoring. The result was the exit of 3774770 m³ of water and the consequently NA fall. The model is considered representative for the...

Análise numérica de um sistema integrado coletor solar/armazenador térmico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência à fadiga de infraestruturas de zircônia: influência da estratégia de cimentação

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise de junta aparafusada de biela automotiva

Pós-graduação em Engenharia Mecânica - FEG

Projeto de um tanque de armazenamento atmosférico com teto flutuante para estocagem de gasolina

In this paper are discussed the main project stages of an atmospheric storage tank with floating roof. It emphasizes the calculations of the bottom, the shell and the floating roof, discussing its stages and conditions, based on the technical standards of the project. The storage tanks are static equipment working under low pressure and has an essential importance for the operation of a process plant. This paper has the purpose of obtaining the dimensions and materials of each component of the tank through the calculations and prove them with results obtained by numerical simulation by finite elements with the help of Autodesk Inventor software, consolidating the project

Aplicação da Simulação de Monte Carlo no estudo de testes de fadiga em rodas agrícolas

Due to the increasing demand from clients and the search for better performances in the heavy vehicles industry, a progressive evolution in technology in a general way was needed. This paper uses a scientific method to validate, prior to its manufacture, the project of an agricultural wheel for sugar cane harvesters. Monte Carlo Simulation is used in conjunction with Finite Elements Method, in order to simulate the wheel's behavior in a cornering test, identify possible failure regions and get an estimate for its life under fatigue. To this end, test conditions according to EUWA Standards were simulated and obeyed, relevant to fatigue. Simulation results were interesting, according to industry experts involved in the project and manufacture of the product in question, and have provided important elements for the decision making regarding improvements that could be made on the product project before its execution

Simulação da suspensão tipo duplo A de um veículo off-road através do histórico de excitação do solo

The search for mechanical components validation methods, employed in product development sector, becomes more avid for less expensive solutions. As a result, programs that can simulate forces acting on a given part through finite element method are gaining more space in the market, once this process consumes less capital when compared to currently-employed empirical validation. This article shows the simulation of an off-road prototype suspension through such technique, using ground excitation history coming from field measurements and also by making use of a specific tool for obtaining dynamic loads from the model in question. The results shown at the end is key for future enhancements aiming mass reduction, for example, that may be executed on the prototype suspension system discussed here