280 resultados para desgaste do dressador


Relevância:

10.00% 10.00%

Publicador:

Resumo:

The search for materials with higher properties and characteristics (wear resistance, oxidation, corrosion, etc.) has driven research of various materials. Among the materials that are being studied with such properties and characteristics are super alloys based on nickel which has an important role in the aeronautical, automotive, marine, production of gas turbines and now in space vehicles, rocket engineering , experimental aircraft, nuclear reactors, steam-powered plants, petrochemical and many other applications because besides having all the characteristics and properties mentioned above also have an excellent performance at high temperatures. The super alloy based on nickel studied in this work is the super alloy Pyromet 31v normally used in the manufacture of exhaust valves in common engines and diesel engines of high power by cater requirements such as mechanical strength and corrosion resistance at temperatures of approximately 815 ° C. The objective of this work is to produce results to demonstrate more specific information about the real influence of coatings on cutting tools and cutting fluids in turning and thus promote the optimization of the machining of these alloys. The super alloy Pyromet 31v was processed through turning, being performed with various machining parameters such as cutting speed, feed rate, depth in conditions of Minimum Amount of Fluid (MAF), abundant fluid, cutting tools with coating and without coating in early in his work life and with wear. After turning were obtained several samples of chips and the part generated during the machining process, was measured roughness of the material, subsequently made macrostructural analysis of the tools used order to detect possible wear and microstructural analysis of samples collected being that the latter was used for Optical Microscopy, Scanning Electron Microscopy (SEM) and ... (Complete abstract click electronic access below)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The computed tomography, devised by Godfrey Hounsfield and Allan Cormack, is in its fourth decade of the clinical use and has presented to be a very useful tool in the diagnosis of several pathologies. For this reason, its use is increasing each day, due to technological progress since its creation. Due to be more and more utilized, the equipment must be in good operating conditions, because it is subject to variance and wearing, damage the quality of diagnosis. To evaluate whether the performance of the scanner remains constant along the time and the dose received by the patient is within the desired limits, periodic tests of quality control must be performed. For this subject, the regulation 453 (June 01, 1998) was created, which determines the need of the implementation of a program for quality assurance (PGQ), where, in addition to the tests of quality control, are established the necessary measurements for the proper functioning of the equipment, generating a trustworthy diagnosis, reducing the dose for the patient and the costs. In this document, are presented tests of quality control carried out in hospitals of the city of Sao Paulo carried out together with the Technical Section of Applications by Imaging Diagnostic (STADI) of the Institute of Electrotechnics and Energy of the University of São Paulo (IEE/USP)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Alloy Al-7%Si-0,3Mg (AA356), having an excellent combination of properties such as low solidification shrinkage and good fluidity, good weldability, high wear resistance, high strength to weight particularly in the automotive and aerospace engineering. The refinement of the structure aluminum silicon eutectic alloy is a fairly common practice in the casting, through the treatment knows as modification. You can get the modification for the addition of chemicals and rare earths, these have the ability to modify the structure of the eutectic, but only sodium and strontium produce a strong action modifier when used in low concentrations. The modifying effect of silicon grain turns into a fibrous form branched and enveloped by the metal matrix in the form of a composite structure that has the highest limit of tensile strength, ductility and machinability. This work will be obtained AA356 alloy ingots using two different types of molds: metal mold and sand mold. Macrographs will be made in ingots obtained for observation of the macrostructures obtained in both types of ingots. Will be sampled at strategic locations of the ingots to correlate microstructure and cooling rate. The results showed that the material of the ingot has a strong influence on the resulting micro-andmacrostructure

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Como a busca por vitórias se torna cada vez mais difícil no esporte coletivo, qualquer vantagem é vista como um diferencial em cada partida. Além da vantagem física e tática, que seriam os mais tradicionais, os treinadores buscam outros meios como vantagem psicológica ou jogar com o mando de campo, que para muitos não passa de ter a torcida a favor, mas para os jogadores e treinadores a torcida tem papel importante de incentivar e para os adversários os deixar nervosos, também não se esquecendo da vantagem de conhecer e treinar no local do jogo alem de poupar os atletas do desgaste de viagens. Este trabalho visa verificar como o mando de campo interfere nos atletas de futsal, alem de como as variadas torcidas influenciam os jogadores durante a partida e como os atletas vêem seus companheiros de time. Foi realizado uma pesquisa bibliográfica e de campo, pela técnica de questionário fechado, que possibilitou a compreensão do fato em estudo, ampliando nossa visão. No decorrer de nosso estudo constatamos que de maneira geral jogar em casa é fator determinante para o resultado final da partida, o que menos motiva os atletas é a possibilidade do juiz ser influenciado pela torcida local e que o grupo masculino é mais fácil de ser motivado do que o grupo feminino. Com os resultados obtidos o treinador passa a conhecer melhor seus jogadores, podendo assim, talvez, escalar o time melhor em momentos difíceis.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The current competitiveness of the market has generated the need to minimize the cost of production companies in any field of activity, aimed at reducing the cost of production, the cost of purchasing and manufacturing processes interruption of manufacturing processes for possible maintenance. In this sense, companies are seeking methods to improve and streamline their production line. In ceramics industries, cooking the pieces is the portion of the production process that influences the total costs. The oven construction and maintenance represent a large portion embedded in the cost of the final ceramic product. The proposal for a type of oven for baking the parts that takes into account a better burning process, knowledge of the causes of disease and cost analysis of purchasing both of the constituent materials and labor for its construction, can be significant importance to the composition of final product costs or time analysis of ROI. It is proposed a streamlined design of an oven that takes into account the positive characteristics of the furnaces already built and that the experience has endorsed, and also others that are added at the end, lead to a reduction in production cost, the cost income and the number of pathologies arising from wear of the furnace along the lifespan. Therefore, according to the experiences gained over the years in the construction of furnaces and experience of manufacturing of ceramic, it is proposed a project that has an oven improvement over those now being built and that include, among other topics, economy in fuel burning, streamlining the building process

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The consuming of the natural resources in the agricultural sector does not represent only one external factor of the productive process, but also it implies in a bigger cost for the production, justified for this environmental degradation. In view of the necessity of evaluating the sustainment of the agricultural businesses, the use of performance indicators if makes of extreme importance. The measurement of the support through environmentalindicators is one of the most accepted forms of performing the evaluation of one given agricultural activity. In this context, the Base System for Eco-certification of Agricultural Businesses (Eco-cert Rural) developed by the Embrapa Environment at Jaguariúna/SP, has for purpose to present a method of evaluation of the agricultural businesses, not only of the point of view of the ecological performance, as well as considering the social, economic and organizational aspects. Through the analysis of the performance of the activity and the regularization of the disconformities found, it makes possible the eco-certification of the activities in the varied existing protocols, offering technologies designed to the sustainable development of the agricultural businesses. Using Eco-cert.Rural, this work evaluated the contribution of the use of mechanized harvest in sugar cane handling, front to the traditional system of manual harvest, using the fire. In the Sugar Cane Activity General Performance Index, Agrícola Rio Claro scored 2,08 of a maximum of 15. Amongst all the indicators, those wich reached performance worse had been related to the Use of Energy and the Income, by increasing fossil fuel consumptiom, and implying income concentration due to resignations of rural workers. However, the improvements on the environment quality by supressing manual harvest through fire are very significant. Beyond the great reduction in...(Complete abstract click electronic access below)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The Sanding is a complex process involving many variables that affect the quality of the part produced, working mainly in the timber industry in the production of panels (MDF, MDP, HDF, etc...) and furniture. However, these industries use the sanding process empirically, not optimizing it. The aim of this study was to compare the behavior of sandpaper white aluminum oxide (OA-white) and Black silicon carbide (SiC-black), analyzing variables in the process as: strength, power, emission, vibration, wear particle size of sanding, and its consequences on the surface finish of the workpiece. Made the process of plane grinding samples of Pinus elliottii, processed in parallel to the fibers, which were sanded with sandpaper grain OA white and black 3-SiC abrasive conditions (new, moderately eroded and severely eroded) grain sizes in 3 (80, 100, and 120 mesh). 6 replicates was performed for each condition tested. Each trial was captured output variables of the sanding process: strength, power, emission and vibration. With two stages totaling 108 trials. After the sanded samples, it has the same surface quality by raising the surface roughness Ra. Through experiment, it can be concluded that abrasives OA-white tended to have higher strength, power, emissions and less vibration in the sanding process, compared to the SiC-black. However, surface finish exhibited similar to the particle size of 80 to 100 mesh, worn abrasive conditions. However, the particle size of 120 mesh, obtained by the roughness of sandpaper OA-bank was higher compared to SiC-black to all conditions of sandpaper due to its toughness

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The region encompassed by the cities of Bocaina’s Historic Valley has your formation closely linked to the coffee´s culture, that were installed during the nineteenth century bringing, at first, a great economic and population growth. However, with the time, the incorrect wear land of the area combined with the antislavery movement and the discovery of more fertile soils in western of São Paulo, among other factors, brought serious setbacks for coffee production in the region which ultimately migrate to other areas, causing an economic crisis in the region that endures to this day. Thus, this paper aims to conduct a study that part of an update of the concept of physiology landscape to identify the physical, ecological and social facts that make up the area of this region, to understand the real causes and consequences of the crisis and what potential persist to circumvent it

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Due to the rapid development of some species such as pine and eucalyptus and a growing demand for raw materials, timber, there was a need for detailed studies to better use and higher quality in products derived from wood. In order to contribute to to better utilization of wood ,this study aims to analyze the quality of the wood surface after machining Corymbia citrodora around, with varying feed rates (40, 70, 100 mm/mim), shear rate (1.88, 2.19, 2.51 m/s) and with the use of inserts for turning new and used (cemented carbide). 18 were used bodies and each body was made three different assays for each test were a total of 54 tests three replicates. This study will also addres the analysis of power consumption for each of the tests. With the results obtained through experiments, including the surface roughness of parts and power consumption for each test, we try to evaluate the power consumption in machining with the variations in cutting speed and feed, with two tools carbide

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Shearplate is an optical glass plate having two flat surfaces and a small angle between them. The use of a high quality shear plate is essential to implement shear interferometric technique . The shear interferometry is a technique used to evaluate the light beam collimation. In order to guarantee the shearplate quality , the complete manufacturing process must be thoroughly monitored. In the manufacturing process, the first step consisted of the glass selection. The selected glass has been submitted to the process of cutting, gluing, chamfering, grinding and polishing. Each phase has been strictly monitored. The quality of the final result depends extremely on an appropriate starting condition, which arises from the grinding process, as the polishing process only recovers the brightness of the part, acting on a small scale on the wearing off of the part, as well as not changing the structured obtained in the grinding process. Respecting all stages of the manufacturing process, the quality of the part has evolved to a good result. The best result obtained showed PV distance of 162 nm, slightly less than λ / 4. This result is significant because the dimensions of the piece with respect to the dimensions of the polisher what interferes directly in the results. The closer are the dimensions of piece and the dimensions of the polisher, the greater the difficulty in controlling the propagation of errors

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The present work aims to study the characteristics of the alloy Al - 7 % Si - 0 , 3Mg ( AA356 ) , more specifically characterize the macrostructure and microstructure and mechanical properties of the alloy ingots AA356 obtained in metal molds and sand molds for power studying the structures through the difference of cooling rates . This alloy is explained by the fact of referring league has excellent combination of properties such as low solidification shrinkage and good fluidity, good weldability , high wear resistance , high strength to weight ratio, has wide application in general engineering , and particularly in the automotive and aerospace engineering . In this work we will verify this difference in properties through two different cooling rates . We monitor the solid solidification temperatures by thermocouples building with them the cooling curve as a tool that will aid us to evaluate the effectiveness of the grain refining because it achieved with some important properties of the alloy as the latent heat of solidification fraction the liquid and solid temperatures, the total solidification time, and identify the presence of inoculants for grain refinement. Thermal analysis will be supported by the study of graphic software “Origin “will be achieved where the cooling curve and its first derivative that is the cooling rate. Made thermal analysis, analysis will be made in macrographs ingots obtained for observation of macrostructures obtained in both types of ingots and also analysis of micrographs where sampling will occur in strategic positions ingots to correlate with the microstructure. Finally will be collecting data from Brinell hardness of ingots and so then correlating the properties of their respective ingots with cooling rate. We found that obtained with cast metal ingots showed superior properties to the ingots obtained with sand mold

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The machining of super alloys resistant to high temperatures such as nickel alloys, inconel 718 specifically, is a very difficult job to obtain improvements in the process, due to the difficulty of machining at high cutting speeds, the use of these alloys in industries showed great developments in recent years, its application in aeronautical industry spread being used in vane turbo, compressor parts, props and set elements. The automotive, chemical, medical and others also took advantage of the great features of inconel 718 and has used the material. The high temperature resistant alloys have high machining difficulty, a fact that is associated with high cutting forces generated during machining which result in high temperatures. High levels of temperatures can cause deterioration of the cutting edge, with subsequent deformation or breakage, wear most common obtained in machining such materials are flank wear the formation of built-up edge for cutting and notch wear. The experimental part of the work consists in machining of nickel-based alloy Inconel 718 heat treated for hardness, using a tool based ceramic silicon nitride Sandvik (Si3N4) in order to compare the best results obtained in the master's thesis of SANTOS (2010) who used a tool ceramics also the basis of silicon nitride which was developed in the doctoral thesis of SOUZA (2005). Assays were performed on a CNC lathe and was noted for each cutting edge results obtained. Tests were made starting from an initial condition of the tool with cutting speed of 200 m/min, feed 0.5 mm and 0.5 mm depth of cut was reduced cutting speed for the subsequent tests with the same conditions of feed and depth of cut. The tool presented wear instant under two 200 m/min and 100 m/min, premature rupture of 50 m/min and finally cut provided with difficulty... (Complete abstract click electronic access below)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The weight of a vehicle has always been considered an extreme important factor, because it interferes in the performance, steering, consume, environmental impact, wear of components, among the others. Because of the new demand, consume reduction aim and gases emission increased the necessity to manufacture lighter vehicles, guaranteeing the complying with the gas emission international law. Besides the legal demand, the low weight will certainly be essential for the competitiveness for the next generation of vehicles. It is with this thinking the composite materials have been introduced in the automobilist industry, because those materials show an excellent relation of strength/weight, providing a reduction of consume and the increase of load capacity. Those factors justify the increase of interest of industry and the necessity of optimization of those materials and of their process. For this research, the field of application will be the Baja SAE Project, a project that is fully developed by engineering students, where they build a prototype single seat, off-road category, for use on hilly slopes with obstacle. This research aims to study two key components of the prototype are made of composite materials, analyzing all the processing. In addition, there is the analysis of the viability of this production parts to a Baja SAE vehicle, in order to increase their performance and reduce their weight without reducing the safety and robustness of the prototype. It was possible to achieve weight reduction of the steering subsystem with manufacturing the flywheel hybrid composite (carbon/glass) and the replacement of SAE 1010 steel by hybrid composite (carbon/aramid) in CVT box. The importance of this study is to obtain a good project for the vehicle of technical and scientific manner, contributing to the know-how to the team and providing a basis for optimization for upcoming projects

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Pós-graduação em Engenharia Mecânica - FEG

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Pós-graduação em Engenharia Mecânica - FEB