The putative Leishmania telomerase RNA (leishTER) undergoes trans-splicing and contains a conserved template sequence

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Distribuição espacial da deriva de produtos fitossanitários em pulverizações na cultura da laranja

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Métodos híbridos de pontos interiores/exteriores e de aproximantes de funções em problemas multiobjetivo de despacho econômico e ambiental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Métodos de aplicação e de avaliação do residual de fungicidas no controle de mofo-branco em soja e feijão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aplicações da função logarítmica em sala de aula no ensino médio: uma proposta de solução de problemas pela transposição para a linguagem matemática

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de um pulverizador e volume ultra baixo e de adjuvantes em caldas fitossanitárias na cultura dos citros

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Modelagem matemática e comportamento dinâmico da suspensão passiva de um pulverizador agrícola autopropelido

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Inspeção periódica de pulverizadores nas principais regiões de produção de soja no Brasil

The aim of this study was to evaluate the evolution of calibration and maintenance practices for crop sprayers on soybean production areas in Brazil, in the 2006 and 2007 seasons, based on the Project IPP data. Therefore, the evaluation covered issues related to calibration, maintenance condition and the main components of 103 sprayers distributed in the following states: Rio Grande do Sul (35), Paraná (60), and, Mato Grosso do Sul (8). The evaluations were done at the rate of one sprayer per farm. The most frequent problems were related to the pressure gauge, spray leaks and calibration errors greater than 50% of the desired volume rate. The analysis of the application rate showed a tendency for the farmers to apply volume rates below the desired value. In 2006 the errors of the application rate were significant, with 70.4% for Rio Grande do Sul State, 74.5% for Paraná State and 37.5% for Mato Grosso do Sul State. In 2007 there was a reduction of errors, with averages of 50.0% for Rio Grande do Sul and 66.7% for Paraná. In general terms, the results showed improvements on the use, maintenance and calibration processes for crop sprayers on the areas covered by the Project IPP, with reductions on average indexes for calibration errors, leaks and bad tips, among other issues.

Avaliação do tempo de resposta de um controlador de fluxo com DGPS submetido à variação de velocidade de voo em condições de voo simulado em laboratório

The application of pesticides is one of the most important steps in the agricultural production process. The spray volume can directly affect application success, and this parameter is directly dependent on the displacement speed of the sprayer. In conventional systems, the operator has to maintain a constant speed to ensure uniform application along the tracks. In order to improve over application quality and preserve levels of precision for applied doses; the use of electronic flow control systems allows for automatic adjustment of volume applied over the area when there is a change in velocity during application. The objective of this research was to study the response times of a flow controller with DGPS for aerial application subjected to variations of velocity in laboratory simulated flight conditions. For this purpose, a bench test has been developed including software for simulating DGPS signals, which was used to simulate different flight speeds and conditions. The results showed the average response time from the flow controller to a change in velocity to be between 6 and 20 seconds. Variations in total flow and the controller setting had a significant influence on response time with situations where there was interaction between the factors being evaluated. There was a tendency for better response times using a constant setting for the control algorithm other than that specified by the manufacturer. The flow controller presented an average error rates below 2% in all evaluated operating conditions, providing satisfactory accuracy in determining the output of product in different test situations.

Tecnologias de aplicação de produtos fitossanitários no controle de percevejos pragas na cultura da soja

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Equipamentos de pulverização associados a volumes de calda e avaliados por alvos artificiais em cafeeiro

The aim of this study was to evaluate the quality of spray droplet spectrum on coffee tree, by using different equipments and syrup volumes. The experiment was set up in a coffee farm, Acaiá variety, Campos Gerais city, MG, Brazil. The treatments were three syrup volumes (150, 300 and 600 L/ha). The lower volume was sprayed with the pneumatic sprayer Martignani, Whirlwind B612 Autonom-Trac mode, and the other volume rates using the conventional hydraulic sprayer to coffee tree. It was possible concludes that the spray volume can be reduced in applications on coffee tree using the pneumatic sprayer.

Determinação comparativa do grau de deformação plástica aplicado a componentes obtidos por conformação

The manufacturing process of components of Pressure Vessels has a great importance in the efficiency during the operation and life cycle of the equipment. Taking this into account, the objective of this dissertation was to analyze the methods to determine the strain rate in formed components by measuring the components themselves, and posterior results comparison with the values found in manufacturing standards of Pressure vessels. In this study the whole manufacturing process of a component from a pressure vessel, known as Head or End, was accompanied. Using the methodology obtained from literatures it was possible to execute the relative and logarithmic deformation measurements of these components and compare with the obtained results by means of equations presented in the Standards as AD-Merkblatt and ASME (for pressure vessels). The found results were also compared with the logarithmic methodology, taking into account the deformation of the empirical mesh and the thickness of the components studied. It is possible to conclude from this study that despite the existence of empirical methods of measurement of strain rate in components plastically formed, it is recommended the adoption in all situation of the component manufacturing standard. It can be noticed and explained during the development of this study and through the results found