Piezoelectric transducers assessed by the pencil lead break for impedance-based structural health monitoring

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Contribution of electrical parameters on the dynamical behaviour of a nonlinear electromagnetic damper

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural damage detection in an aeronautical panel using analysis of variance

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Active modal damping control of a smart truss structure using a self-organizing fuzzy controller

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

beta-Lactamase-based biosensor for the electrochemical determination of benzylpenicillin in milk

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A synergistic combination of reduced graphene oxide and antimony nanoparticles for estriol hormone detection

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Interferometric measurements of nanometric displacements in a Piezoelectric Flextensional Actuator by using the new J1...J5 method

In this work, nanometric displacement amplitudes of a Piezoelectric Flextensional Actuator (PFA) designed using the topology optimization technique and operating in its linear range are measured by using a homodyne Michelson interferometer. A new improved version of the J1...J4 method for optical phase measurements, named J1...J5 method, is presented, which is of easier implementation than the original one. This is a passive phase detection scheme, unaffected by signal fading, source instabilities and changes in visibility. Experimental results using this improvement were compared with those obtained by using the J1... J4, J1...J6(pos) and J1...J 6(neg) methods, concluding that the dynamic range is increased while maintaining the sensitivity. Analysis based on the 1/f voltage noise and random fading show the new method is more stable to phase drift than all those methods. © 2012 IEEE.

Ultrasound effect in the removal of intraradicular posts cemented with different materials

This study evaluated the effect of ultrasonic vibration on the tensile strength required to remove intraradicular post cemented with different materials. Bovine teeth were selected, and 7 mm of the cervical root canals were prepared to size 5 Largo drill, the posts were cemented with zinc phosphate, Enforce (resin) or Rely X (glass ionomer). The specimens were divided into six groups (n = 10), according to the following procedures: GI-cementation with zinc phosphate associated with traction force; GII-cementation with zinc phosphate associated with ultrasonic activation and traction force; G111-cementation with Enforce associated with traction force; GIV-cementation with Enforce associated with ultrasonic activation and traction force; GV-cementation with Rely X associated with traction force; and GVI-cementation with Rely X associated with ultrasonic activation and traction force. The tensile test was conducted using the electromechanical testing machine, the force was determined by a specialized computer program and ultrasonic activation using the Jet Sonic Four Plus (Gnatus) device in 10P. Concerning to average ranking, GI showed statistically significant difference in comparison with GII and GVI (p < 0.05); there was no statistical difference in GIII and GIV when compared to other groups (p > 0.05). The ultrasound favored the intraradicular post traction regardless of the employed cement in greater or lesser extent. The post removal is a routine practice in the dental office, therefore, new solutions and better alternatives are need to the practitioner. We did not find in the literature many articles referring to this practice. Thus, the results from this study are relevant in the case planning and to promote more treatment options.

Desenvolvimento de um sistema de SHM sem fio e com compensação automática de temperatura

Pós-graduação em Engenharia Elétrica - FEIS

Avaliação do método da quebra do grafite para estimação da sensibilidade de transdutores piezelétricos utilizados na técnica da Impedância Eletromecânica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aplicação do método de impedância eletromecânica na detecção da queima no processo de retificação plana

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento e avaliação de desempenho de um sistema de posicionamento automático para painéis fotovoltaicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aeroelastic Analysis of a Typical Section Using of Shape memory wire actuator

Shape memory alloys (SMAs) provide a compact and effective actuation for a variety of mechanical systems. In this paper, a numerical simulation study of a three degree of-freedom airfoil, subjected to two-dimensional incompressible inviscid flow using a SMA is presented. SMA wire actuators are used to control the flap movement of a wing section. Through the thermo-mechanical constitutive equation of the SMA proposed by Brison, we simulate numerically the behavior of a double SMA wire actuator. Two SMA actuators are used: one to move the flap down and the other to move the flap up. Through the numerical results conducted in the present study, the behavior and characteristics of an SMA actuator with two SMA wires are shown the effectiveness of the SMA actuator. In conclusion, this paper shows the feasibility of using SMA wire actuators for flap movement, with success

Apresentação de métodos para implementação de plataformas colaborativas de Sistemas Automatizados de Produção

Automated Production Systems Development involves aspects concerning the integration of technological components that exist on the market, such as: Programmable Logic Controllers (PLC), robot manipulators, various sensors and actuators, image processing systems, communication networks and collaborative supervisory systems; all integrated into a single application. This paper proposes an automated platform for experimentation, implemented through typical architecture for Automated Production Systems, which integrates the technological components described above, in order to allow researchers and students to carry out practical laboratory activities. These activities will complement the theoretical knowledge acquired by the students in the classroom, thus improving their training and professional skills. A platform designed using this generic structure will allow users to work within an educational environment that reflects most aspects found in Industrial Automated Manufacturing Systems, such as technology integration, communication networks, process control and production management. In addition, this platform offers the possibility complete automated process of control and supervision via remote connection through the internet (WebLab), enabling knowledge sharing between different teaching and research groups.

Leveraging wireless devices for networked control systems in industrial applications

Networked control systems (NCSs) are distributed control system in which sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks(WNCS)which enable interoperability between existing wiredand wireless systems. This paper presents the feasibility analysis of using serial to wireless converter as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the wireless converter capabilities. In addition the control performance of an implemented motor control system using the converter is analyzed. Experimental results led to the conclusion that serial ZigBee device isrecommended against the Bluetooth as it provided better metrics for control applications. However, bothdevices can be used to implement WNCS providing transmission rates and closed control loop times which are acceptable for NCS applications.Moreoverthe use of thewireless device delay in the PID controller discretization can improve the control performance of the system.