Análise teórica e experimental de uma ventaneira de alto forno, visando seu comportamento térmico e fluidodinâmico

In this work, it was studied the thermal and fluid dynamic behavior from theorical and experimental point of view of a blast furnace tuyere. The tuyere is responsible for the hot air insuflation into the blast furnace. The parameter used in the comparison was the difference between the cooling water inlet and outlet temperatures. There were used forced convection correlations inside circular sections with adequations for non circular sections. Based on operations dates of flux and thermal loads it was possible to model numerically the tuyere, and, since it was obtained the wall temperatures, estimate the conduction and convection resistances and the heat flux through the walls in contact with the water. The total heat fluxes from wall to water were applied to the energy conservation equation where could be estimated the theorical temperature variation. Compared to the real value, the theorical value presented a difference of 0,2 °C. Considering that the boundary conditions around the tuyere are transitories and that your channels have some rugosity irregularities we can consider the estimation method for cooling system coherent with the real operational parameters

Estudo de causas de falhas em selos mecânicos de bombas centrífugas para circulação de óleo térmico

This study is about a heating line that uses thermal oil. It is located in a facility that produces interlayers used in cars windshields. A plastic resin is melted and is sent to a matrix called DIE where the interlayers are produced. The DIE needs to receive heat from the circulation of thermal oil in four different regions of its interior, to ensure the correct thickness of the interlayer. The thermal energy is provided by electric heaters and the flow of thermal oil is impelled by four mechanically sealed centrifugal pumps (one per region). The key point of this study is the fact that these four pumps of the system have reported successive failures in the mechanical seals. Apparently, a poorly designed project has burdened the system intermittently. The pumps operation condition is located in a region of low efficiency, according to the characteristic curves. This fact is the source of the noticeable reduced time between failures. Changes in the configuration of the facility and in the number of pumps will be proposed, aiming to achieve higher operational efficiency. The proposals will be mathematically analyzed according to the Hydraulic Institute criteria. At the same time, we will also keep focus on an in-depth study of a heating system structure, starting with a detailed approach for each component and discussion about its real need and economic viability. At the end of this paper it is shown that the gain in efficiency achieved with the new proposed configuration reflects not only in the reduction of maintenance costs, but also a potential improvement in energy efficiency. It is shown that these two aspects are closely related and together form the basis for the design of a reliable and efficient pumping system

Estudo sobre fornos de tratamento térmico e propostas de cogeração de energia em usina siderurgica não integrada

Steel industry is a sector heavily dependent on energy, both electrical and thermal. Since the receipt of raw materials to the shipment of finished products to customers, through mergers, casting, rolling, heat treatment, inspection, among others, high amounts of energy are demanded, generating very significant costs to the productive chain in its entirety . Therefore, any alternative that favors the reduction in energy consumption or barateie the cost of this is very welcome. Within this context, this paper aims to make a technical and economic analysis of installing a cogeneration plant in the field rolling in a non-integrated steel mill. Two configurations are proposed plants, with one being the use of heat from waste gases from furnaces existing in the area mentioned and another with the use of heat from waste gases from an internal combustion engine. Both proposals are evaluated technically and later is done the economic analysis, calculating the financial return (pay back) in relation to the investment required, operation and maintenance of the plant

Avaliação da influência da taxa de resfriamento posterior ao tratamento térmico nas propriedades mecânicas do aço API 5L X70

In this work a study about the mechanical properties of the API 5L X70 steel, with or without heat treating, has been made, with the intetion of assess the influence of cooling after the austenitization heat treating by air cooling (normalizing) and a rapid cooling with oil (tempering). This steel is known by high strength and ductility values and it is commonly used in the manufacture of oil pipes. The growing energy demand encouraged the study and manufacture of this material. Although this microalloyed dispense subsequent heat treatings, it was proven that its implementation is very advantageous for this type of application, improving hardness and plastic stability. It was also assessed that the faster the cooling rate is, the better will be these properties

Estudo do comportamento térmico e reológico de amidos na conformação cerâmica de compostos multicamada com alumina, titanato de alumínio e dióxido de titânio

The project aims to develop ceramic compounds with gradients of the mechanical properties, using the molding technique with commercial starches. To understand the process of interaction between starch and ceramic powders, the proposed methodology involves viscometry tests (up to 200 °C). Viscometric assays were carried out with slurries of alumina, titania and aluminum titanate with potato starch, cassava and corn. The specimens were tested for dilatometry, thermomechanical, thermal shock, mechanical and characterization by SEM. The ceramic powders and starches were analyzed using the optical microscope to measure the size of these. It was made of th kinetics of starch gelatinization and titania with the cornstarch in theoptical microscope to observe how the grains of starch behaved in welling

Flat hotel

Projeto de um Flat Hotel na cidade de Presidente Prudente, para atender, principalmente, a demanda de empresários e estudantes que buscam um ambiente versátil e com autonomia maior que a de um hotel convencional, oferecendo espaços para a realização de suas atividades com o conforto de uma residência e a facilidade dos serviços de hotelaria. O desempenho no cumprimento das funções, somado a uma arquitetura de qualidade, nos sentidos práticos e plásticos, são os objetivos principais deste trabalho

Síntese, caracterização e estudo do comportamento térmico dos oxanatos de lantanídeos(III) e de ítrio(III), no estado sólido

Pós-graduação em Química - IQ

Comportamentos, térmico e mecânico, de compósitos de polipropileno e resíduo da hidrólise enzimática do bagaço de cana de açúcar

Pós-graduação em Engenharia Mecânica - FEG

Uso de microarray para determinação da expressão gênica diferencial em oócitos Bos Taurus Indicus e Bos Taurus Taurus submetidos ao estresse térmico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Validação de métodos nociceptivos elétrico, mecânico e térmico para avaliação de dor de equinos tratados com metadona associada à detomidinaou acepromazina

Pós-graduação em Anestesiologia - FMB

Efeito da limpeza pós-condicionamento e do tratamento térmico do silano na resistência de união de um cimento resinoso à cerâmica

Pós-graduação em Odontologia - FOA

Efeito do tratamento térmico em cerâmica feldspáticas silanizada na adesão do cimento resinoso

Pós-graduação em Odontologia Restauradora - ICT

Estudo das alterações das propriedades mecânicas em aço A-516 grau 70 soldado e submetido a tratamento térmico de alívio de tensões

Pressure vessels are equipments that require a great care because of their high cost and human life risk in case of fail, and its fabrication methods are different for each manufacturer. Normally, pressure vessels and its parts are fabricated by welding, which may change local properties of metals. The head of a pressure vessel is a very important structural component and it is fabricated by welding and mechanical conformation. Because its excellent mechanical properties, de steel A-516 Grade 70 is often used in manufacturing of large pressure vessels that are subjected to high pressure and temperature, but was verified that its mechanical resistance is decreased when submitted to a tension relief heat treatment. By experience it was defined that before mechanical conformation of the head of a large pressure vessel, the steel should be submitted to a stress relief heat treatment in order to facilitate the mechanical conformation, but there is no quantitative analysis to prove this method and study its possible risks. In the present work the steel A-516 Grade 70 demonstrated a decrease of its mechanical resistance when submitted to a stress relief heat treatment, but keeping above the minimum limit defined in the literature. By other side its ductility was substantially increased, being possible to deduce that the stress relief heat treatment before mechanical conformation is a viable e recommended technique, but with reservations. With the data acquired during the fabrication e preparation of the specimen and the result of the tests, it was possible to elaborate a welding procedure that provides the same results obtained in this present work

Caracterização química e estudo térmico de lodos provenientes da estação de tratamento de esgotos de Ribeirão Preto, SP, Brasil

Pós-graduação em Química - IQ

Dinâmica não linear e projeto de controle em sistemas de transporte vertical: comportamentos periódicos e caóticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)