Comparison of cyclic fatigue and torsional resistance in reciprocating single-file systems and continuous rotary instrumentation systems

As compared with continuous rotary systems, reciprocating motion is believed to increase the fatigue resistance of NiTi instruments. We compared the cyclic fatigue and torsional resistance of reciprocating single-file systems and continuous rotary instrumentation systems in simulated root canals. Eighty instruments from the ProTaper Universal, WaveOne, MTwo, and Reciproc systems (n = 20) were submitted to dynamic bending testing in stainless-steel simulated curved canals. Axial displacement of the simulated canals was performed with half of the instruments (n = 10), with back-and-forth movements in a range of 1.5 mm. Time until fracture was recorded, and the number of cycles until instrument fracture was calculated. Cyclic fatigue resistance was greater for reciprocating systems than for rotary systems (P < 0.05). Instruments from the Reciproc and WaveOne systems significantly differed only when axial displacement occurred (P < 0.05). Instruments of the ProTaper Universal and MTwo systems did not significantly differ (P > 0.05). Cyclic fatigue and torsional resistance were greater for reciprocating systems than for continuous rotary systems, irrespective of axial displacement.

Complex modal analysis of a slender vertical rotor by finite elements method

In this paper, natural frequencies were analyzed (axial, torsional and flexural) and frequency response of a vertical rotor with a hard disk at the edge through the classical modal and complex analysis. The equation that rules the movement was obtained through the Lagrangian formulation. The model considered the effects of bending, torsion and axial deformation of the shaft, besides the gravitational and gyroscopic effects. The finite element method was used to discretize the structure into hollow cylindrical elements with 12 degrees of freedom. Mass, stiffness and gyroscopic matrices were explained consistently. The classical modal analysis, usually applied to stationary structures, does not consider an important characteristic of rotating machinery which are the methods of forward and backward whirl. Initially, through the traditional modal analysis, axial and torsional natural frequencies were obtained in a static shaft, since they do not suffer the influence of gyroscopic effects. Later research was performed by complex modal analysis. This type of tool, based on the use of complex coordinates to describe the dynamic behavior of rotating shaft, allows the decomposition of the system in two submodes, backward and forward. Thus, it is possible to clearly visualize that the orbit and direction of the precessional motion around the line of the rotating shaft is not deformed. A finite element program was developed using MATLAB (TM) and numerical simulations were performed to validate this model. Natural frequencies and directional frequency forced response (dFRF) were obtained using the complex modal analysis for a simple vertical rotor and also for a typical drill string used in the construction of oil wells.

Avaliação da influência dos parâmetros de processo de soldagem MIG no surgimento de poros em tubos de alumínio

The process of electric arc welding with shielding gas (GMAW) is being increasingly used in various industrial applications. This process occurs by which an electric arc is established between the work piece and a consumable in the form of wire, the arc melts the wire continuously as it is fed to the weld pool. The weld metal is protected from the atmosphere by flowing a gas (or gas mixture) inert or active. This paper presents a study of the welding process GMAW - MIG on aluminum tubes, alloy 6101 - T6, used in the manufacture of armored busbar, intended for driving electric power plants. 5(five) were welded specimens, changing certain welding parameters at each time was monitored welding joint as well as the interpass temperature. Tests were performed bending, tensile and macrographical analysis of body-of-evidence and through its results was possible to reach a better welding condition, which minimizes the appearance of pores, since the porosity has great influence on the mechanical strength and electrical conductivity of welded pipes

Painel particulado composto por casca de eucalipto na camada intermediária

This work was developed to evalute the physical and mechanical properties of a panel of three particle layers from the test specification of NBR 14810-3 (2006), using wood of Eucalyptus sp. and Eucalyptus saligna and Eucalyptus urograndis bark. The mechanical properties were evaluated to obtain the bending modulus of rupture (MOR) and modulus of elasticity (MOE) and Internal bond. The physical properties were obtained thickness sweeling, water absorption, moisture content and board density. Were evaluated four different compositions of panels containing 5, 10, 15 and 20% in the inner layer of bark. The results were compared with the Brazilian standard NBR 14810-2 (2006) and also with studies in the literature. The panels produced were adequate to all the optimal values suggested by the standard only in the composition with 5% skin in the inner layer. The other treatments showed satisfactory results in all tests except for moisture content

Caracterização físico-mecânica de painel de MDP produzido com madeira de Eucalipto e Bracatinga

This work is the production of particleboard of particles reconstituted from MDP (Medium Density Particleboard) adding particles in the inner layer of Mimosa Scarelli, popularly known as bracatinga, the ratios of 0%, 25%, 50%, 75% and 100%. The panel produced is composed of three layers, two external particles with smaller particle size and an inner layer composed of particles of larger particle sizes. Assays were performed based on physical and mechanical NBR 14.810/2006 for the determination of the board density, thickness swelling, water absorption, moisture content, bending strength, shear strength and residual moisture, and testing of particle size not existing in the standard cited. The results were analyzed and compared the results of the commercial boards made from 100% eucalyptus, based on the limits specified by the ABNT NBR 14.810/2006. The values of the tests were close to the normative specifications indicating positively the production of MDP with wood decay.

Redução de empeno em barra trefiladas do aço SAE 9254

In this paper we study the process of manufacture of wire drawn steel bars 9254, from rolled wire rod. These bars are used in the automotive industry for the manufacture of coil springs, which make up the system damping of several vehicles. The wire drawing process consists of the steps of pre-straightening, shot peening, drawing, cutting and polishing. The study aims to search for the configuration of process variables, which present the best result with respect to bending. To this were maintained settings prestraightening and mechanical stripping and varied angles and stringer polish being studied to replace the spinneret with a working angle, for a string with two working angles. To assist in the analysis of the results was the tool used DOE Software Minitab, which assesses the variation in results according to each parameter and the interaction parameters. It was thus possible to determine the best condition for wire drawing

Obtenção de constantes elásticas da madeira de duas espécies de Pinus sp

There are many studies about longitudinal modulus of elasticity of wood, but you can´t say the same of transverse modulus, especially for conifers. The study aimed to characterize and compare the species Pinus elliottii var. elliottii and Pinus elliottii var. elliottii x Pinus cariabeae hondurensis (hybrid), and the longitudinal modulus of elasticity (E) and lateral (G) in bending, to analyze the modulus of elasticity in different spaces and to verify the species studied the ideal range is equal to 21 times the height of the specimen, as prescribed in the normative document NBR 7190/1997, as well as analyzing the relationship G = E/20 defined in the normative document NBR 7190/1997. The wood came from the farm located in Paranapanema, split at the mill São José and the rest of the work was conducted at the Experimental Itapeva Campus - UNESP. Were removed fourteen specimens of each species. The average values of the modulus of elasticity and cross were, respectively, 5828 MPa and 452 MPa for Pinus elliottii var. elliottii and 6407 MPa and 320 MPa for the species of Pinus elliottii var. elliottii x Pinus cariabeae hondurensis (hybrid). The trend lines for the plotted graphs showed an exponential behavior to near linear 21he will equal the constant after this value. We have found the relationship G = E/13, for Pinus elliottii var. elliottii and G = E/20 for hybrid. The results of the modulus and strength for Pinus elliottii var. elliottii and the hybrid were lower than those reported in the literature, showing that this batch inferior quality to apply to structures

Estudo comparativo de dois tipos de painéis de MDP: com adição de papel impregnado e lâminas de bambu

This work is the production of two types of particle boards reconstructed MDP (Medium Density Particleboard), the first with the addition, in the inner layer of particles of impregnated paper, the ratios of 0%, 1%, 5% and 20 %. In the second type of panel MDP was inserted with blades of bamboo species Dendrocalumus giganteus as coatings and structural reinforcement. The MDP panel, used as a basis for both cases has the composition of three layers, two external particles with smaller particle size and an inner layer composed of particles of larger particle sizes. Assays were performed based on physical and mechanical NBR 14.810/2006 for the determination of the board density, thickness swelling, water absorption, moisture content, bending, tension parallel and perpendicular, and testing of particle sizes of the particles did not exists in standard references. The results were analyzed and compared the results of the commercial boards made from 100% eucalyptus, based on the limits specified by the ABNT NBR 14.810/2006. The values of the tests showed similar results indicating normative specifications in a positive way, the possibility of production of MDP with the use of waste paper impregnated. As for the panel with bamboo blades, the tests showed a mechanical performance far superior to MDP market, explaining the study and possible implementation of the bamboo for use where the MDP will suffer greater mechanical stress, such as doors, tops and benches tables

Análise das propriedades físico-mecânicas de painel particulado de eucalipto composto por três camadas com duas variações de pressão

The research aimed to produce sheets of particles with waste processing of Eucalyptus sp bonded with urea-formaldehyde and evaluate the effect of pressure variation in the quality of the boards produced. To do so, the Boards made were divided into two treatments depending on the pressing pressure of 30 to 40 kgf / cm². Once pressings, climatized, the particleboards have been sectioned in test samples, and underwent physical-mechanical tests for determining density, swelling and water absorption, modulus of rupture and elasticity in static bending and internal linking. The particleboards pressed at 40 kgf / cm ² showed the best results

Processamento do compósito de fibra de capim-sapê / epóxi e avaliação da resistência à flexão “t” de Student

In recent years a great worldwide interest has arisen for the development of new technologies that enable the use of products with less environmental impact. The replacement of synthetic fiber plants is a possibility very important because this fiber is renewable, biodegradable and few cost and cause less environmental impact. Given the above, this work proposes to develop polymeric composites of epoxy resin and study the behavior of these materials. Both, the epoxy resin used as matrix in the manufacture of sapegrass fiber composite, as tree composites formed by: epoxy/unidirectional sapegrass long fiber, 75% epoxy/25% short fiber, by volume, and 80% epoxy/20% short fiber, by volume, were characterized by bending, and the composites produced with short fibers random were inspected by Optical Microscopy and Acoustics Inspection (C-Scan). For the analysis of the sapegrass fiber morphology, composites 75% epoxy/25% short fiber (sheet chopped) and 80% epoxy/20% short fiber images were obtained by optical microscope and the adhesion between polymer/fiber was visualized. As results, the flexural strength of composites epoxy/unidirectional long fibers, 75% epoxy/25% short fiber and 80% epoxy/20% short fiber were 70.36 MPa, 21.26 MPa, 25.07 MPa, respectively. Being that composite showed that the best results was made up of long fibers, because it had a value of higher flexural strength than other composites analyzed

Avaliação de momentos fletores em estruturas de fundação tipo radier em concreto armado

It aims the comparison of these moments between an analytical plates theory and a computational numerical simulation. It is accented the details of studies about analytical theory as well the process, step by step, of a program that has as an influence the method of finite elements. The theory of plates has an extremely importance when it is talked about slabs and it takes as a base some fundamental hypotheses (that the middle point of the plate is considered flat and under formable) the points that are normal in relation to the middle surface is not considered because of its intensity that is irrelevant in comparison to the rest. The computational programs offer good results when they are applied in a correct way and, it resolves numerous functions in a short period of time. The objective is to highlight the importance of bending moments, its points of maximum and minimum, that has the objective of realize a good reinforcement sizing for a reinforced concrete. Furthermore, it can propitiate an economy in places that is demanded a small quantity of steel, before dimensioned for a load that is distributed in all the surface of the plate, at the same intensity

Projeto mecânico do sistema de transmissão de um veículo Baja

This study aims to determine the best configuration for the new gearbox of the new Baja´s vehicle from Piratas do Vale team, focusing on the gear train, in order to achieve high performance of it. To this end, first some information about the vehicle is gathered to determine the best pair of gears configuration, then calculations about maximum bending stress, fatigue and surface thereof are performed; ; thereafter static simulations are performed using an a appropriated software. Thus this paper shows a satisfactory design of the addressed, besides providing the Baja SAE team consultation material for future use in the project

Desempenho estrutural de vigas em madeira laminada colada armada

The objective of the present work was to evaluate Pinus’ glued laminated timber (glulam) beams and steel reinforced glulam beams, using PU mono-component adhesive in lamination step and epoxy adhesive to bond steel bars. The mechanical performance was verified through bending test, and the adopted method based on homogenized section, to considerate the differences between wood and steel mechanical properties. The homogenization section method proved itself effective in obtaining the stiffness of the parts in MLCA. The stiffness of reinforced beams increased 91% in comparison with glulam beams, differing only 5.5 % from value of stiffness calculated

Fractografia quantitativa e o conceito de tenacidade à fratura para a análise do efeitodo choque térmicos em TiO2

The present study evaluated the use of semicircular bending test (SCB) as an alternative to conventional bending test to examine the effect of thermal shock. Still, studies the behavior of fracture surfaces generated by monofractal behavior analysis, which allows us to evaluate the contributions of the microstructure and the mechanical context in forming reliefs during the crack propagation. The fractal analysis is made from elevation maps obtained by reconstruction method by extension of the focus stacks of digital images acquired in microscope. The specimens used were samples semicircular pressed TiO2 (rutile) with and without heat shock, prepared for testing mode I loading. Were also produced, specimens in the form of bars for Weibull statistical analysis. From the three-point bending test, we found the variation of fracture toughness between the samples after the heat shock and natural condition. The SCB test was feasible for the analysis of thermal shock resistance. The results showed that the value of the fracture toughness decreases as the heat shock treatment

Caracterização do defeito tipo trinca de laminação, ocorrido no processo de laminação de barras de aço

The mechanical forming processes are the main means of transformation. Among all processes, the most used is rolling and broken down into flat and non-flat products. In the flat products are classified plates, and products no plans bars and profiles. Thus laminating products, mostly, are the raw materials for other processes of transformation, as stamping, forging, machining, bending and more. This work has focused on non-flat products, classified as bars and rods, watching a key point in the proceedings that is the product quality. Here is demonstrated through metallographic analysis of steel bars, hot-rolled, the characteristics of surface cracks in these bars